• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.224-227
• /
• 1997

This study discuss two subjects : maximization of transmission capability and regulation of voltages along line within the permissible bounds. Series and parallel line compensation methods have been applied for those purposes using capacitors and reactors. In this paper, the effect of series and shunt line compensation for symmetrical line is analyzed. The results obtained in this paper can be applied 765kV class EHV transmission system.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.201-203
• /
• 2005

A new 3-phase line-interactive UPS(Uninterruptible Power Supply) system with parallel-series active power-line conditioning capability using AC line reactor and two four-leg PWM VSCs(Voltage Source Converters) was introduced recently, In this paper, the strategy of voltage control in suggested UPS system is explained. The objective of proposed voltage controllers in parallel(shunt) and series PWM VSC is to guarantee satisfactory characteristics in steady state and transient state.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.202-207
• /
• 2002

This paper deals with a novel shunted actuator, which has a capability to suppress multi-mode vibration amplitudes by using a pair of piezoceramic patches. In order to describe the characteristic behaviors of shunted dampers connected with a series and a parallel resistor-negative capacitive branch circuit, the stiffness ratio and loss factor with respect to the non-dimensional frequency are considered. To obtain a guideline model of a piezo/beam system connected with a series and a parallel resistor-negative capacitor branch circuit, the governing equations of motion is derived through Hamiltons principle and a piezo sensor equation as well as a shunt damping matrix is developed. The theoretical analysis shows that the shunted actuator developed in this study can significantly reduce multiple-mode vibration amplitudes simultaneously over the whole structural frequency range.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 E
• /
• pp.1647-1649
• /
• 1998

This paper describes the power frequency voltage and its countermeasure when a 765 kV transmission line is directly connected to a 345 kV line and operated at 345 kV voltage. The summary of this result is as follows : The western route of 765 kV transmission line doesn't need any countermeasure to reduce the power frequency voltage at the receiving end. The eastern route of 765 kV transmission needs 100 Mvar(3 phase) capacity of shunt reactor at the receiving end to reduce the power frequency voltage. The use of shunt reactors in the 765 kV transmission lines has unexpected problems, one of which is induction of high voltages on a de-energized circuit of two parallel lines. This paper examined the problem of resonance on two parallel transmission circuits in one routes.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1219-1221
• /
• 2005

We improved quench properties of a superconducting fault current limiter(SFCL) components based on YBCO thin films. This consists of three components with nearly identical properties and one with slightly difference properties. The units were connected in series and first of parallel to increase the current and voltage ratings. It have caused significantly imbalanced power distribution. The imbalance remarkably improved by connecting a shunt reactor to the SFCL component in parallel.

• 한국초전도ㆍ저온공학회논문지
• /
• 제8권4호
• /
• pp.22-25
• /
• 2006

This paper deals with the computation of the current limiting behavior of high-temperature superconducting (HTS) modules for the superconducting fault current limiter (SFCL). The SFCL module consists of a monofilar type BSCCO-2212 tube and a shunt coil made of copper or brass. The shunt coil is connected to the monofilar superconducting tube in parallel. Through analysis of the quench behavior of the monofilar component with shunt coils, it is achieved to drive an equivalent circuit equation from the experimental circuit structure. In order to analyze the quench behavior of the SFCL module, we derived a partial differential equation technique. Inductance of the monofilar component and the impedance of the shunt coil are calculated by Bio-Savart and Ohm's formula, respectively. We computed the quench behavior using the calculated values, and compared the results with experimental results for the quench characteristics of a component. The results of computation and test agreed well each other, and it was concluded that the analytic result could be applied effectively to design of the distribution-level SFCL system.

• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.1311-1318
• /
• 2015

This paper introduces a novel topology and an effective control strategy for a shunt hybrid power filter (SHPF) to simultaneously compensate harmonic currents and reactive power. The proposed SHPF topology is composed of an LC passive filter tuned to the 7^th harmonic frequency and a small-rated active filter connected in parallel with the inductor L_pf of the LC passive filter. Together with the SHPF topology, we also propose a control strategy, which consists of a proportional-integral (PI) controller for DC-link voltage regulation and a PI plus repetitive current controller, in order to compensate both the harmonic current and the reactive power without the need for additional hardware. Thanks to the effectiveness of the proposed control scheme, the supply current is sufficiently compensated to be sinusoidal and in-phase with the supply voltage, regardless of the distorted and phase lagging of the load current. The effectiveness of the proposed SHPF topology and control strategy is verified by simulated and experimental results.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권11호
• /
• pp.737-741
• /
• 2000

We fabricated resistive superconducting fault current limiters (SFCL) based on YBCO thin films grown on 2-inch diameter $Al_2O_3$ substrates. Two SFCLs with nearly identical properties were connected in series to investigate simultaneous quench. There was a slight difference in the rate of voltage increase between two SFCL units when they were operated independently. This difference resulted in significantly imbalanced power dissipation between the units. This imbalance was removed by connecting a shunt resister to an SFCL in parallel. The appropriate values of shunt resistance were 80 ${\Omega}$ at 75 $V_rms$ and 110 ${\Omega}$ at 120 $V_rms$, respectively. Increased power input at high voltages also reduced the initial imbalance in power dissipation, but with increase in film temperature to higher than 200 K.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.343-347
• /
• 1999

YBCO film을 이용한 meander 형태의 저항형 한류기에서 고장이 발생하였을 때 초기의 과도상태에서 볼수 있는 첨두전류를 억제하기 위하여 shunt 저항을 병렬로 취부한 경우의 전기적특성을 살펴보았다. 인가전압을 16.5 V$_{peak}$로 가하고 R$_0$는 1 ${\omega}$,R$_L$을 7.7 ${\omega}$으로 하고 shunt 저항을 5 ${\omega}$으로 하였을 때 약 12.2 A$_{peak}$의 전류값에서 최초quench가 발생하였으며 초전도 한류소자에 quench 발생으로 인한 저항이 발생함과 동시에 I$_1$으로 흐르던 사고전류의 일부가 shunt 저항이있는 I$_2$으로 서서히 분로하여 첨두전류가 거의 발생하지 않았다. 이때 초전도 한류기를 적용하지 않은 경우 최대 사고전류는 약 16.5 A$_{peak}$이었으며 초전도 한류기를 적용한 경우는 최대 한류전류값이 9 A$_{peak}$에서 4주기후에는 5.8 A$_{peak}$이었다. 인가전압 V$_0$=113 V$_{peak}$이고 표준저항 R$_0$는 1${\omega}$, 그리고 R$_L$을 7.7 ${\omega}$으로 하고 shunt 저항을 5 ${\omega}$으로 하였을 때 사고각 0 $^{\circ}$에서 사고전류값이 최고 23.0 A$_{peak}$까지 상승하고 이후 일정한 값을 유지하였다. 일반적으로 사고발생 직후에는 전류변화율에 의하여 전류값의 급격한 상승을 보이지만 shunt 저항이 전류분류의 역할을 수행하여 첨두전류는 거의 발생하지 않았다. 또한 상온의 gold층의 저항을 감안했을 때 사고발생후 약 36msec 후에 상온에 도달하였으며 shunt 저항이 없는 경우의 11 msec에 비하여 약 3배이상 길어졌다. 사고각 45 $^{\circ}$와 90 $^{\circ}$인 경우는 반복실험에 의한 시편의 특성저하(degradation)에 의하여 정상상태에서 초전도체에 흐르는 전류가 약간 발생하였다. 계통의 신뢰성이 중요한 요소로 작용하는 실제운전에서는 시편의 특성저하에 의한 quench전류의 감소를 감안하여 적절한 운전조건을 도출하여야 한다. 이상에서 앞으로는 장기간의 실제운전 조건을 고려하여 시편의 특성저하(degradation)와 가혹조건에 대한 전기적 특성에 대한 연구를 병행하고자 한다.

• 한국산학기술학회논문지
• /
• 제7권6호
• /
• pp.1072-1077
• /
• 2006

본 논문은 AC 라인 리액터와 2개의 4레그 PWM 전압형 컨버터를 사용하여 병렬 및 직렬 능동필터 기능을 가지는 새로운 3상 Line-Interactive UPS 시스템을 제안하고 전압제어 방식을 설명한다. 제안하는 UPS 시스템의 병렬 및 직렬 PWM 전압형 컨버터에서 전압제어의 목적은 정상상태 및 과도상태에서 만족스러운 동작 특성을 보장하는 것이다.