• Structural Engineering and Mechanics
• /
• 제68권5호
• /
• pp.603-619
• /
• 2018

In this research, an effective computational technique is carried out for nonlinear and post-buckling analyses of cracked imperfect composite plates. The laminated plates are assumed to be moderately thick so that the analysis can be carried out based on the first-order shear deformation theory. Geometric non-linearity is introduced in the way of von-Karman assumptions for the strain-displacement equations. The Ritz technique is applied using Legendre polynomials for the primary variable approximations. The crack is modeled by partitioning the entire domain of the plates into several sub-plates and therefore the plate decomposition technique is implemented in this research. The penalty technique is used for imposing the interface continuity between the sub-plates. Different out-of-plane essential boundary conditions such as clamp, simply support or free conditions will be assumed in this research by defining the relevant displacement functions. For in-plane boundary conditions, lateral expansions of the unloaded edges are completely free while the loaded edges are assumed to move straight but restricted to move laterally. With the formulation presented here, the plates can be subjected to biaxial compressive loads, therefore a sensitivity analysis is performed with respect to the applied load direction, along the parallel or perpendicular to the crack axis. The integrals of potential energy are numerically computed using Gauss-Lobatto quadrature formulas to get adequate accuracy. Then, the obtained non-linear system of equations is solved by the Newton-Raphson method. Finally, the results are presented to show the influence of crack length, various locations of crack, load direction, boundary conditions and different values of initial imperfection on nonlinear and post-buckling behavior of laminates.

• Journal of Mechanical Science and Technology
• /
• 제15권10호
• /
• pp.1386-1397
• /
• 2001

In this paper, the plane elasticity equations are used to investigate the in-plane normal (mode I) and shear (mode II) behavior of a crack perpendicular to and terminating at the interface in bonded media with a graded interfacial zone. The interfacial Bone is treated as a nonhomogeneous interlayer with the continuously varying elastic modulus between the two dissimilar, homogeneous semi-infinite constituents. For each of the individual loading modes, based on the Fourier integral transform technique, a singular integral equation with a Cauchy kernel is derived in a separate but parallel manner. In the numerical results, the values of corresponding modes of stress intensity factors are illustrated for various combinations of material and geometric parameters of the bonded media in conjunction with the effect of the material nonhomogeneity within the graded interfacial zone.

• 터널과지하공간
• /
• 제2권2호
• /
• pp.251-264
• /
• 1992

In this study, the size effect in measuring the fracture toughness of rock was investigated using the ISRM Suggested Method for Fracture toughness using Chevron Bend Specimens. Total 58 specimens were prepared with 4 different diameters, 29, 42, 54, 68mm and center cut-chevron notch. In addition to this, to evaluated the effect of anisotropy of Jecheon granite, which is the sample for this study, core drilling direction was adjusted perpendicular(short transverse) and parallel(arrester) to the rift plane in the sample and the measured fracture toughness for each direction were compared. Important results obtained from this study are as follows. Level ll test condition is more adequate than l, because of low data scattering and precision and corrected fracture toughness of Jechoen granite measured and 2.2MPa{{{{ SQRT { m} }}}} for arrester direction with minimum initial crack length 0.7cm. From the relationship between core diameter and initial crack length presented in the ISRM testing method, the specimen diameter should be bigger than 47mm. The fracture toughnesses measured for arrester and short transverse directon show 10% difference. This is to the anisotropy of Jecheon granite possessing rift plane.

• International Journal of Concrete Structures and Materials
• /
• 제18권3E호
• /
• pp.207-211
• /
• 2006

This paper presents an experimental study on the repair performance of sprayed engineered cementitious composites(ECC) serving as a repair material. Sprayable ECC, which exhibit tensile strain-hardening behavior in the hardened state and maintain sprayable properties in the fresh state, have been developed by using a parallel control of micromechanical design and rheological process design. The effectiveness of sprayable ECC in providing durable repaired structures was assessed by spraying the ECC and testing them for the assessment. The experimental results revealed that, when sprayed ECC were used as a repair material, both load carrying capacity and ductility represented by the deformation capacity at peak load of the repaired flexural beams were obviously increased compared to those of commercial prepackaged mortar(PM) repaired beams. The significant enhancement in the energy absorption capacity and tight crack width control of the ECC repair system treated with wet-mix spraying process suggests that sprayed ECC can be effective in extending the service life of rehabilitated infrastructures.

• 한국강구조학회 논문집
• /
• 제14권6호
• /
• pp.773-782
• /
• 2002

본 연구에서는 향후 사용빈도가 증가할 것으로 예상되는 SM570, POSTEN60 및 POSTEN80 강재를 대상으로 용접선 방향이 피로균열성장속도에 미치는 영향, 용접방법 및 강도등급에 따른 피로균열성장특성, 그리고 각 재질별(모재부, 열영향부, 용접금속부) 피로균열 성장특성을 정량적으로 평가하기 위해서 CT시험편을 제작해서 일련의 피로시험을 실시하였다. 피로시험결과 노치가 용접선과 평행한 시험체의 경우 노치선단에 존재하는 압축잔류응력의 영향으로 노치가 용접선과 직각인 시험체의 경우보다 피로균열성장속도의 지연현상이 현저해지는 것을 알 수 있었다. 그리고 용접 방법에 따른 피로균열성장특성은 강재의 강도등급에 관계없이 FCAW가 SAW에 비해서 피로균열성장속도의 분산이 적게 나타나고 있으며, 또한 높은 응력확대계수범위 영역에서 피로균열성장속도의 수렴현상이 나타나는 것을 알 수 있었다. 한편 본 피로시험결과와 기존의 연구결과를 비교하면 피로균열성장영역에서의 피로균열성장속도는 유사한 경향을 나타내고 있으므로 본 연구에서 대상으로 한 강재는 피로안전성을 충분히 확보하고 있음을 알 수 있었다.

• Structural Engineering and Mechanics
• /
• 제68권4호
• /
• pp.497-505
• /
• 2018

Three points bending flexural test was modeled numerically to study the crack propagation in the pre-cracked beams. The pre-existing edge cracks in the beam models were considered to investigate the crack propagation and coalescence paths within the modeled samples. The effects of particle size on the single edge-notched round bar in bending test were considered too. The results show that Failure pattern is constant by increasing the ball diameter. Tensile cracks are dominant mode of failure. These crack initiates from notch tip, propagate parallel to loading axis and coalescence with upper model boundary. Number of cracks increase by decreasing the ball diameter. Also, tensile fracture toughness was decreased with increasing the particle size. In the present study, the influences of particles sizes on the cracks propagations and coalescences in the brittle materials such as rocks and concretes are numerically analyzed by using a three dimensional particle flow code (PFC3D). These analyses improve the understanding of the stability of rocks and concretes structures such as rock slopes, tunnel constructions and underground openings.

• 한국재료학회지
• /
• 제12권6호
• /
• pp.508-512
• /
• 2002

$2000{\AA}-SiO_2/Si(100)$ and $560{\AA}-Si_3N_4/Si(100)$ wafers, which are 10 cm in diameter, were directly bonded using a rapid thermal annealing method. We fixed the anneal time of 30 second and varied the anneal temperatures from 600 to $1200^{\circ}C$. The bond strength of bonded wafer pairs at given anneal temperature were evaluated by a razor blade crack opening method and a four-point bonding method, respectively. The results clearly slow that the four-point bending method is more suitable for evaluating the small bond strength of 80~430 mJ/$\m^2$ compared to the razor blade crack opening method, which shows no anneal temperature dependence in small bond strength.

• 한국음향학회지
• /
• 제16권1호
• /
• pp.5-9
• /
• 1997

스터드 볼트에 존재하는 작은 결함은 초기에 발견되지 않으면 작은 결함이라도 결함 크기가 급진전되어 전체적인 파손에 이른다. 그러나 이러한 나삿니의 응력부식결함이나 부식 찌꺼기와 같은 것은 가동중검사에서 일반적인 초음파 검사로써는 검출이 어렵다. 본 연구에서는 디지탈신호처리에 의한 결함 검출 방법을 보인다. 초음파가 나삿니에 평행하게 입사된다면 연속적인 나삿니로부터 발생되는 신호는 거의 일정한 시간 간격을 가지고 있다. 이러한 연속적인 나삿니신호는 예측 간격에 의해 처음 신호를 기초로 다음 신호를 추측할 수 있는 데 여기서 최적 연산자를 사용해 예측되는 연속적인 나삿니신호를 제거하여 결함 신호를 검출할 수 있다.

• Smart Structures and Systems
• /
• 제22권6호
• /
• pp.663-673
• /
• 2018

In this study, the effect of particle size on the cracks propagation and coalescence or cracking pattern of the edge notched disc specimens are investigated. Firstly, calibration of PFC3D was performed using Brazilian experimental test output. Then micro parameters were used to build edge notched disc specimen. The horizontal wall of the assembly is let to move downward with a standard low speed of 0.016 m/s. The numerical results show that the tensile cracks are dominant failure pattern for the modeled discs. These tensile cracks initiate from the pre-existing notch tip and propagate parallel to the loading direction then interact with the upper boundary of the modeled specimen. As the size of the balls (ball diameter) decrease the number of tensile cracks increase. The tensile fracture toughness of the samples also decreases as the particle size increases. Understanding the crack propagation and crack coalescence phenomena in brittle materials such as concretes and rocks is of paramount importance in the stability analyses for engineering structures such as rock slopes, underground structures and tunneling.

• 대한금속재료학회지
• /
• 제49권2호
• /
• pp.112-120
• /
• 2011

The out-of-phase thermo-mechanical fatigue (OP TMF) in a <001> oriented single crystal nickel-based superalloy CMSX-4 has been studied. OP TMF life was less than a half of low cycle fatigue(LCF) life in spite of a small hysteresis loop area of OP TMF compared to that of LCF. The failure was caused by the initiation of a crack at the oxide-layered surface followed by its planar growth along the <100> ${\gamma}$ channel in both LCF and OP TMF. However, deformation twins appeared near the major crack of OP TMF. The multiple groups of parallel twin plates on {111} planes provided a preferential path for crack propagation, which caused a significant decrease in OP TMF life. Additionally, the analysis on the surface crack morphology revealed that the tensile strain at the minimum temperature of OP TMF was found to accelerate the crack propagation.