• Geomechanics and Engineering
• /
• v.22 no.5
• /
• pp.449-460
• /
• 2020

The double-lane arrangement model is frequently used in underground coal mines because it is beneficial to improve the mining efficiency of the working face. When the double-lane arrangement is used, the service time of the reserved roadway increases by twice, which causes several difficulties for the maintenance of the roadway. Given the severe non-uniform deformation of the reserved roadway in the Buertai Coal Mine, the stress distribution law in the mining area, the failure characteristics of roadway and the control effect of support resistance (SR) were systematically studied through on-site monitoring, FLAC 3D numerical simulation, mechanical model analysis. The research shows that the deformation and failure of the reserved roadway mainly manifested as asymmetrical roof sag and floor heave in the region behind the working face, and the roof dripping phenomenon occurred in the severe roof sag area. After the coal is mined out, the stress adjustment around goaf will happen to some extent. For example, the magnitude, direction, and confining pressure ratio of the principal stress at different positions will change. Under the influence of high-stress rotation, the plastic zone of the weak surrounding rock is expanded asymmetrically, which finally leads to the asymmetric failure of roadway. The existing roadway support has a limited effect on the control of the stress field and plastic zone, i.e., the anchor cable reinforcement cannot fully control the roadway deformation under given conditions. Based on obtained results, using roadway grouting and advanced hydraulic support during the secondary mining of the panel 22205 is proposed to ensure roadway safety. This study provides a reference for the stability control of roadway with similar geological conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.50-55
• /
• 2018

Earthquakes are almost impossible to predict and take place in a short time. In addition, there is little time to take aggressive action when an earthquake occurs. Therefore, there are more casualties and property damage than with other natural disasters. Recently, earthquakes have been occurring all over the world. As the number of earthquakes increase, studies on the safety of structures are being carried out. On the other hand, there are few studies on the electric facilities, which are relatively non - structural factors. Currently, electrical equipment in Korea is often not designed for earthquake safety and is quite vulnerable to damage when an earthquake occurs. Therefore, in this study, modeling was conducted through ABAQUS similar to an actual cabinet panel and 3D dynamic nonlinear analysis was performed using a natural seismic. According to seismic zone I and normal ground rock conditions of the power transmission and transmission facility seismic design practical guide, the maximum response acceleration of the performance level was 0.157g. In this study, however, it was not safe to reach the limit state of 30% of the analytical result at 0.1g for the general cabinet panel. From the results, the seismic fragility curve was derived and analyzed. The derived seismic fragility curve is presented as a quantitative basis for determining the limit state of the cabinet panel and can be utilized as basic data in related research.

• Journal of Korea Multimedia Society
• /
• v.11 no.2
• /
• pp.175-181
• /
• 2008

A 2 dimensional quality function for quantifying the quality of images observed at viewing regions in contact-type multiview 3 dimensional imaging systems is devised and its effectiveness is verified experimentally. The function allows calculating the locations of viewing regions for patched images of any number of different view images. The images observed at the calculated regions reveal that different parts of the display panel of the system project different view images and match with the function's prediction.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.317-323
• /
• 2000

The purpose of this study is to compare the seismic resistant capacity inherent in ductile moment resisting frames using two different joint modeling. The difference between these two models is the capability for considering the panel zone deformation. For this purpose, 5 story steel moment frame is designed in compliance to the Korean seismic design provisions and the steel structure design standard. Nonlinear Static Procedure(NSP) and Nonlinear Dynamic Procedure(NDP) of this structure are carried out using two different joint models. Based on the results of NSP and NDP, the sensitivity of the response to analytical modeling is appraised. Also, it is proposed that for the highrise steel structures, the joint deformation should be accounted properly by the analytical model.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.21-24
• /
• 2005

In this study, new methods of PC panel connection using 'ㄷ'type steel connection is proposed for highly seismic zone. A study was carry out to investigate the connection behavior subjected to cyclic inelastic loading. Three planar type and two T type PC wall will be tested. The variables will be examined were the shear reinforcement existence of top and bottom walls. The specimens will be tested only reverse cyclic loading in accordance with a prescribed displacement history. To transfer the shear strength shear key set up between top and bottom wall. Failure mode, behavior, ductility and energy dissipation capacity of the specimens constructed by new connections wll be compared with those of monolithic walls and Han's(Han, Jun Hee, Seoul National University) model.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.3
• /
• pp.23-34
• /
• 2000

반복하중을 지지하는 4개의 2/3 크리 접합부 실험을 통하여 콘크리트 기둥 및 강재 보로 구성된 골조에 대한 외부 모멘트 접합부의 이력거동을 조사하였다. 주요 실험 변수는 접합부에 배치된 후프근의 수, 콘크리트만의 전단강도 발현응ㄹ 유도한 접합부 상세, 강재 보 플랜지 상, 하부에 스터드 형태의 전단키를 사용한 상세 등이다. 실험 시 관측된 균열양상, 파괴형상 및 다양한 계측결과에 근거하여 접합부 상세에 따른 각 시험체의 거동이 자세히 기술되었으며, 항복 후 보유강도, 강성저하 정도 및 에너지 소산능력 등이 분석되었다. 실험결과에 의하면, 이들 중 패널 및 인접 기둥 영역에 각각 2개의 후프근을 갖는 시험체 (CF3) 가 가장 우수한 이력응답을 나타냈으며, 이러한 형태의 접합부 상헤는 우리나와 같은 약진 지역에 적합할 것으로 판단되었다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.03a
• /
• pp.36-39
• /
• 1998

To predict strain distributions and weld line movements in the forming processes of tailored blank sheets, the 2-dimensional finite element formulation is developed. The welding zone is modelled with the several, narrow finite elements. The material properties of weld elements are calculated from those of base metals, based on the experimental evaluation. To verify the finite element formulation developed, the forming process of an autobody door inner panel section is simulated. FEM predictions are compared and showed good agreements with experimental measurements.

• Journal of Korean Society of Steel Construction
• /
• v.8 no.4 s.29
• /
• pp.105-113
• /
• 1996

본 연구에서는 철골모멘트골조의 패널존변형을 명시적으로 고려한 탄성층 간변위의 근사해석 방법을 제안하였다. 본 방법은 고전적 포탈법의 가정 및 D 치법에 기반한 해석적 접근법이다. 즉 포탈법의 가정에 따라 횡력을 받는 골조를 보-기둥 부분 골조로 분해한 후 대표적 내부 부분골조의 보, 기둥 및 패널존에서 기인하는 모든 횡변위 성분을 해석적으로 계산한다. 이때에 필요한 모든 내력(가령 패널존 전단변형 산정을 위한 보의 불균형모멘트)의 결정에 D 치법을 이용한다. 구조바닥의 강막작용을 고려하면 위의 과정을 통하여 산출된 대표적 내부 부분골조의 횡변위는 전체 골조의 횡변위와 거의 동일할 것으로 기대할 수 있다. 본 방법의 타당성 여부는 반강절 접합요소를 사용한 해석적 엄밀해와 비교하여 검증하였으며 만족스런 결과를 주는 것을 확인하였다. 본 연구의 방법에 의해 컴퓨터해석에 의하지 않고도 철골모멘트골조의 탄성층간변위를 실용성있는 정확도로서 신속하게 산정할 수 있으므로 본 연구의 결과는 예비적 횡강성 평가에 유용하게 사용될 수 있다. 또한 본 방법의 적용과정에서 해석자는 철골모멘트골조의 횡변위 기동에 관한 물리적 감각을 증진시킬 수 있을 것으로 사료된다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.3
• /
• pp.205-210
• /
• 2000

The objective of this study is to investigate the structural behavior of steel beam-high strength concrete column joints subjected to reversed cyclic loadings. The variables of the experimental study is amount of steel plates at the beam-to-column joint panel zone. Three specimens were prepared and tested under constant uniaxial load($0.2f_{ck}A_g$) to reinforced high strength concrete column, and the reversed cyclic loads were applied to end of steel beams, The failure modes, hysteresis loop, stiffness degradations and energy dissipation capacities were analyzed and compared for test variables.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.10a
• /
• pp.222-229
• /
• 2000

The purpose of this study is to evaluate and make a comparison between the Ordinary Moment Resisting Frames using different analytical joint model for the Nonlinear response. For this purpose, 3-story structure was designed according to NEHRP 1994 Guidelines. And the center-line dimension model and model considering panel zone were used as analytical model for the structure. Nonlinear Static Procedure and Nonlinear Dynamic Procedure were used to evaluate seismic capacities and demands. The limitation in FEMA 273 was used as the variable number to predicte seismic demands of OMRFs. This analytical studies were performed with DRAIN-2DX modified by Shan Shi. Using the above results, the performance evaluation and seismic demands of OMRFs shall be performed. Finally NSP and NDP shall be compared.