• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.453-458
• /
• 2001

Analysis of radiation heating system for producing 60" size PDP panels was carried out using $RADCAD^{TM}$ software. Optimum arrangement of infrared heating elements was found to obtain uniform temperature distribution in PDP panel during heating. Heating capacity of each heater was determined to obtain an appropriate maximum panel temperature. Parametric study to find the effect of design parameters such as the thermophysical and optical properties of glass and cooling system was carried out. As a reference system, about 35 kW heating capacity was chosen to obtain about 800 K maximum panel temperature after 30 minute heating. The maximum temperature difference in panel was below 20 K. The maximum/minimum and its difference in the panel were very sensitive to the variation of the emissivity of glass and cooling block.

• Information Display
• /
• v.4 no.2
• /
• pp.3-6
• /
• 2003

This paper describes a MacMic System developed for Flat Panel Display. The MacMic System usually is used for testing of Mother Glass of TFT and Color Filter. They are normally consisted of microscopy system, illumination system and panel stage system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.972-977
• /
• 2000

One of the major differences of Korean residential building compared with other countries is a rigid diaphragm of a floor due to the panel heating system. An increment of a gravity floor load might cause vibration problem when the composite floor system is introduced to the panel heating system. Since the noise criteria of a residential building is lower than that of an office building, the development of a noise absorbing system should be preceded. The response evaluation was performed for the finished floor, that is with panel heating and noise absorbing system. The natural frequency was obtained both from an experimental study and an analytical study. An appropriate vibration condition of a floor with panel heating and noise absorbing systems was evaluated from this study.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.12
• /
• pp.1194-1202
• /
• 2011

A touch panel system has been one of the most widely used input devices. In this study, a touch panel embedded system using accelerometers is considered in order to make commercial white-boards or plates into touch panels. Three accelerometers are located at different positions on such a white board, so that touch points on the board can be identified using the sensors. For the identification of touch points, a TDOA (Time Difference of Arrivals) technique is applied in the algorithm which was implemented in a DSP board (TI 6713 DSK), which can provide a precise touch location by using the cross-correlation function of measured signals from the three accelerometers. Experiment results show that the touch panel system with accelerometers could provide the exact touch location. Thus a novel approach using such accelerometers could be applied to a new touch panel system.

• Journal of Power System Engineering
• /
• v.12 no.4
• /
• pp.46-51
• /
• 2008

Honeycomb panel has a constructive advantage because it is constructed with a honeycomb core, so it has relatively higher strength ratio to weight. Therefore honeycomb panel has been used as the light weight panels in the high-speed railway technology and high-speed ship like as cruise yachts. Also it has been used in the aircraft and aerospace industry as a structural panel because light weight structure is indispensible in that field of industry. Recently, the honeycomb panel is embossed in the viewpoints of high oil prices as the lightweight panel of the transport machine, however the sound insulation capacity of the honeycomb panel is poorer than those of uniform and another sandwich panels. In this paper a method to improving the sound absorption coefficient of a honeycomb panel Is studied by using the Helmholtz resonator. The sound absorption coefficients for some kinds of honeycomb cores are demonstrated by the normal incident absorption coefficient method.

• Information Display
• /
• v.5 no.1
• /
• pp.5-12
• /
• 2004

디스플레이 시스템의 경량화, 저전력화, 박형, 저가격화를 가능하게 하는 System On Panel에 대한 중요성 및 관심이 모바일 디스플레이 환경을 중심으로 증가하고 있다. 디스플레이 패널에 내장할 수 있는 프로세서 및 다양한 모듈의 향후 전망을 위하여 집적측면의 Poly-Si TFT 공정 이슈 및 현재 프로세서집적 연구동향, 기존의 디스플레이 관련 프로세서의 아키텍쳐에 대한 소개 및 현재 System On Panel의 상황을 분석하여, 향후 System On Panel을 위한 디스플레이 시스템의 구현 방안 및 다양한 개발 방향을 소개한다.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.11
• /
• pp.45-53
• /
• 2016

A precast panel wall system resists against the horizontal earth pressure by increasing the shear strength of ground by reinforcement connected to the panel. The application of precast panel wall system is growing to lately minimize the earth work and environmental damage caused by large cut slope and to use the limited land effectively. The ground adhered panel wall system is the construction method that has the panel engraved with natural rock shape to improve the landscape. This system is developed to complete Top-Down method, and it is possible to have vertical cut, and to adhere to in-situ ground, improve construction ability by minimizing the ground relaxation and exclusion the trench and backfill process. In this study the field tests were performed to verify the construction ability about the vertical cut and complete Top-Down process and the construction behavior of ground adhered panel wall system was analyzed by large scale loading test and measurement results during loading test.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.11
• /
• pp.2313-2320
• /
• 2011

The management of a panel block shop in a shipyard is a complex process that entails the largest amount of work and in which many decisions are involved. Shipbuilders have considered the process as a bottleneck since every panel for every ship and offshore hull structure must be processed through the shop. In order to maximize process productivity, simulation-based ship production execution system(SPEXS) is proposed for panel block operations utilising discrete-event simulation and simulated annealing. An application of panel block assembly shop, called SPEX-Panel supports production planners by general dispatching rules and metaheuristics to make better scheduling decisions on the shop floor. In addition, the system will help increase productivity in the yard with continuous improvement.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.969-971
• /
• 2002

In this paper, we study the performances of optical system design using the 1 panel LCD without color filter for projection color television. We analyze the optical efficiency compare this system with 1 panel LCD system using the color filter, and work out a constraint condition of 1 panel LCD without color filter for optical design. We design a high brightness 1 panel optical system using a complex reflection mirror and suggest a method of the optical system design.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.499-502
• /
• 2004

The temperature distribution of a glass plate heated in the infrared heating chamber has been investigated. Temperature of the glass panel is measured using a set of thermocouples and the optical pyrometer. Temperatures measured by thermocouples have good agreement with those by the pyrometer. The temperature uniformity of the panel is improved with wall reflectivity, which is one of the important factors to uniformly heat the panel