• 한국환경농학회지
• /
• 제20권4호
• /
• pp.269-276
• /
• 2001

Sulfamoylurea계 제초재의 일종인 cyclosulfamuron의 수도재배환경중 잔류특성을 평가하고자 2개 지역의 포장 및 실험실조건에서 토양 중 잔류성, 토양/토양수 및 수직적 잔류량 분포, 그리고 수확물인 현미 및 볏짚 중 잔류수준을 조사하였다. 경산 및 영천토양 중 잔류특성은 1차 분해반응의 양상을 보였으며 그 반감기는 포장과 실험실조건에서 각각 $17{\sim}30$일 및 $14{\sim}16$일로 나타났다. 입제살포 후 유효성분의 토양/토양수간 분포비율은 시간이 경과할수록 토양으로의 분포비율이 높아졌으며 토양 및 토양수에서의 반감기는 각각 19일과 10일이었다. 감수심 5 cm/일 조건으로 10일간 수행한 용탈 실험에서 cyclosulfamuron은 토심 $0{\sim}4\;cm$에 주로 분포하였으며 토양중 수직이동성은 상당히 제한적이었다. 포장조건에서 입제 및 액상수화제를 수확전 $120{\sim}150$일 전에 $1{\sim}2$회 처리하고 수확한 현미 중 잔류량은 제형, 살포시기 및 회수에 관계없이 모두 0.01 mg/kg 미만이었으며 볏짚중 잔류량은 $<0.02{\sim}0.05$ mg/kg 범위였다. Cyclosulfamuron의 토양 및 토양수 중 비교적 빠른 소실속도와 낮은 이동성을 고려할 때 약제살포에 따른 잔류분이 다른 환경계로의 전이되거나 후작물에 대한 2차 약해를 유발할 가능성은 매우 낮은 것으로 평가된다. 또한 수확물 중 낮은 잔류수준과 독성학적 특성을 감안할 때 수확물 중 잔류분으로 인한 만성독성학적 부작용은 무시하여도 좋다고 판단된다.

• 한국축산시설환경학회지
• /
• 제8권2호
• /
• pp.99-106
• /
• 2002

This study was conducted to improve utilization efficiency of slurry and choose a suitable type of tractor power which can be attached by manure spreader in the paddy field. In the paddy field, the pulling force for the spreader was measured by using a measurement system installed between tractors with and without the spreader. The soil moisture contents at the 0${\sim}$10cm and 10${\sim}$20cm depth of test soil(SiCL) were 28.45% d.b. and 23.47% d.b., respectively in average while Cone Index at l0cm and 15cm depth were 14.5kPa and 16.2kPa, respectively. It was impossible to measure the soil moisture contents and Cone Index below 20cm depth of the soil because the hardness of the soil increased greatly. Thereafter, hard pan of the sampled soil was found at 15${\sim}$20cm depth. While the required power only for the dragged tractor was found to be 3.44kW in the test field, the required pulling powers of tractor considering the pumping were 8.48${\sim}$12.48kW, 12.19${\sim}$16.19kW, 16.96${\sim}$20.96kW, respectively for 2 tons, 3 tons, and 4 tons of tank capacity. As the tank capacity increased, the sinkage of soil were also increased to 7cm, l0cm, and 12cm, respectively for the tractors with 2 tons, 3 tons and 4 tons of tank capacity. Considering about 60% of pulling efficiency of tractor, a tractor which had lower than 25.74kW of pulling power was suitable to pull the spreader and spread the slurry simultaneously for manure spreader with 2 tons of tank capacity. 29.42kW${\sim}$36.78kW of pulling power was found to be optimum for the tractor with 3 tons of tank capacity while over 40.45kW for 4 tons of tank capacity.

• 한국농공학회지
• /
• 제21권2호
• /
• pp.28-36
• /
• 1979

One of most important problems in the Monsoon Asia today is the production of rice paddy to meet the needs of the ever increasing population. Diversemeans are being employed to meet this demand, both by increasing productivity of existing farm land and by bringing further areas into cultivation. The primary step in either field is to ensure that there is sufficient moisture in the soil to suit the paddy, and at the same this means that excess moisture has to be drained off the land, while in others irrigat ion has to be employed to bring sufficient water to an area. In view of the fact that the project comprises a huge amount of earthwork, it can be carried out by extensive use of construction machinery in order to shorten the period. As farm ditch has a comparatively small section with shallow cutting depth, inaddition, there is lack of access road in the field, the excavation equipment with bulldozer or tracter-shovel (backhoe) type are not applicable because there are mostly adapted for the excavation of deep and wide section. Mini-backhoe with its bucket width not larger than 0. 3m, and width of blade not larger than 1. 00m seems to be more adaptable. About 80% of excavation of ditch section will be done by the machinery while the other 20% of excavation together with the finishing of the section are supposed to be done by man-power. The embankment of ditch section can be compacted by the crawler of backhoe when it is moving along the ditch for excavation. However, Lowland paddy field in the Monsoon Asia are made particulary in rain season, therefore, heavy machinery is not easy excavation for ditch. It is very important to know exact ground support power of the working site and select machines with corresponding ground pressure. Ground support power is variable subject to quality and water content of soil and therefore selection of machines should be made duly considering ground condition of the site at the time of construction works. Farm ditches dug and compacted by mannual labar are of poor quality and subject to destruction after one or two years of operation. On the other hand, excavation and compaction by bulldozer is not practical for ditches. Backboe is suitable for slope land, but this is required cycle time of bucket excavation and dumped out. If a small-scale farm ditch trencher adaptable to lowland paddy field is invented, such a machine could greatly accelerate the massive construction work envisaged in many countries and thus significantly speed up the most difficult part of irrigation development and management in Monsoon Asia.

• 대한원격탐사학회지
• /
• 제22권6호
• /
• pp.553-563
• /
• 2006

본 연구의 목적은 MODIS 다중시기영상과 선형분광혼합화소분석(Linear Spectral Mixture Analysis : LSMA)을 이용하여 한반도의 토지피복도를 작성하는 것이다. 다양한 공간해상도와 광역적인 촬영스케일의 MODIS 영상에 LSMA를 이용하여 토지피복분류기 정확도의 향상과 한반도 생물계절적인 특성을 분석하고자 하였다. LSMA는 하나의 화소를 단일의 지표물로 가정하여 영상을 처리하는 기존의 기법과 달리 대상지의 토지피복 특성을 가장 잘 반영하는 순수한 물체의 화소값(Endmember)을 선택하여 자연환경요소들의 하나하나를 분리하는 기법이다. 본 연구에서 MODIS 다중시기 영상에 LSMA를 적용한 결과 남, 북한의 농경지 및 산림지역에 대한 서로 다른 생물계절적인 특성을 파악 할 수 있었으며, 이러한 결과 영상을 ISODATA 무감독분류기법을 통해서 대분류와 중분류하였다. 대분류에서는 79.94%의 전체 정확도를 보였으며, 농업지역은 85.45%, 산림지역은 88.12%로 다른 분류군들에 비해서 가장 높은 정확도를 보였다. 중분류에서는 산림지역과, 농업지역을 더욱 세분화하여 분류하였다. 전체정확도는 82.09%였으며, 활엽수림 86.96%, 논 85.38%로 분류군중 가장 높은 정확도를 나타냈다.

• 한국물환경학회지
• /
• 제24권3호
• /
• pp.333-339
• /
• 2008

This study was carried out to assay the relationships between empirical factors and water quality in 23 agricultural reservoirs. Based on the trophic state index (TSI) deviation analysis, phosphorus in type II and III was the primary limiting factor on algal growth. BOD, COD, TP and chl.a concentration in type III reservoirs showed higher concentration than those of other types, while SS and TN concentration was no noticeable difference among three types. Characteristics of type III reservoirs showed large reservoir surface and drainage area, large surface area to volume (SAV) ratio, small drainage area to reservoir area (DA/RA) ratio, relatively old age, large paddy field and upland field to drainage area ratio (Mean 17.4%) and high generation and discharge loads compared to other types of reservoirs. In type I and II reservoirs, trends of BOD, TN, TP concentration in water column, were similar to those of the discharge load of pollutants. Although type II reservoirs generally showed low phosphorus discharge loads compared to type I reservoirs, TP and chl.a concentration in water column was greater than that of type I. Characteristics of type II reservoirs showed relatively large SAV ratio and old age compared to type I reservoirs and was similar to those of type III including eutrophic reservoirs.

• Journal of Biosystems Engineering
• /
• 제3권1호
• /
• pp.47-63
• /
• 1978

This study was conducted to obtain a basic information necessary to assess present rice milling technology in Korea The profiles for milling plants was analyzed by survey work.For the private custom-work mills, which process about 80 percent of domestic rice consumption ,their actual milling test for the identical samples as used for filed mills was conducted. Two rice varieties Japonica and Tongil-type were associated with the experiments. The results are summarized as follows: 1. Analyses for private custom-work mills showed their general aspects as; about 91 percent of the mills belonged to an individual owner ship ; more than 93 percent of the mills was established earlier than 1950 ; about 80 percent of the mills was powered with electric motor; mills having less than two employees were about 75 percent; about 45 percent of the mills provided for warehouse in storing customers cereal grains. 2. The polishers installed in 1,255mills within the surveyed area (7 counties) have been supplied by 44 different domestic manufacturers ;in but about 60 percent of which was supplied by 6major manufacturers. The polishers could be classified into two categories in terms of principles of their polishing actions ;jet-pearler and friction types. About 51 percent of the mills was equipped with the former which has been recognized as giving greater milling recovery than the friction types. 3. Reason for owners of private mills to supplement new machines was due mainly to pgrading their mills to meet the requirements that established by the Government. However, about 60 percent of the mill owners intended to replace with new pearler by their own needs to meet with new high yielding varieties. 4. Processing systems of each previate rice mills surveyed could be classified into three categories, depending upon whether the systems posessed such components as precleaner and paddy separator or not. Only 36.7 percent of mills was installed with both precleanr ad paddy seperrator, 5.0 percent of mills did have neither percleaner nor paddy seperator, and rest of them equipped only one of the two. Hence,it is needed for about 63% of rice miils to be supplemented with these basic facilities to meet with the requirements for the standaized system. 5. Actual milling capacity measured at each field rice mills was shown a wide variation, having range from about 190 to 1,210 kg/hr. The percentages of mills classified according to daily milling capacity based on this hourly capacity were 24.3% for the capacity less than 3 M/T a day; 20.0% for 3-4 M/T; 15.6% for 4-5 M/T; 6.7% for 5-6 M/T; 22.3% for 6-7 M/T; and 11.0% for more than 7 M/T a day. 6. Actual amount of rice processed was about 310 M/T a year in average. About 42% of total milled rice was processed during October to Decembear, which formed a peak demand period for rice mills. The amount of rice milled during January to May was relatively small, but it had still a large amount compared to that during June to September. 7. Utilization rate of milling facility, i. e., percentage of the actual amount of milled rice to the capacity of rice mills, was about 18% on the year round average, about 41% in the peak demand season, and about 10% during June to September. Average number of operating days for mills surveyed was about 250 days a year, and about 21 days a month. 8. Moisture contents of paddy at the time of field mill tests were ranged 14.5% to 19.5% for both Japonica and Tong-i] varieties, majority of paddy grains having moisture level much higher than 1530. To aviod potential reduction of milling recovery while milling and deterioration of milled rice while storage due to these high grain mJisture contents, it may be very important for farmers holding rice to dry by an artificial drying method. 9. Milling recovery of JapJnica varieties in rice mills was 75.0% in average and it was widely ranged from 69.0% to 78.0 % according to mills. Potential increase in milJing recovery of Japonica variety with improvement of mill facilities was estimated to about 1.9%. On the other hand, milling recovery of Tong-il varieties in the field mill tests was 69.8% in average and it ranged from 62% to 77 %, which is much wider than that of Japonica varieties. It is noticed that the average milling recovery of Tong-il variety of 69.8% was much less than that of the Japonica-type. It was estimated th3.t up to about 5.0% of milling recovery for Tong-il variety could be improved by improving the present lo'.ver graded milling technology. 10. Head rice recoveries, as a factor of representing the quality of commercial goods, of Japonica and Tong-il varieties were 65.9% and 53.8% in average, and they were widely ranged from 52% to 73% and from 44% to 65% , respectively. It was assessed that head rice recovery of Japonica varieties can be improved up 3.3% and that of Tong-il varieties by 7.0% by improving mill components and systems.

• 헤리티지:역사와 과학
• /
• 제33권
• /
• pp.36-67
• /
• 2000

Square-shaped moated burial precincts(方形周溝墓) can be classified into type I that has bridges only at the comers, type II that has bridges at the comers and sides, type III that has bridges only at the sides, type IV that is surrounded by the moat without bridges, type V that has its sides less than those of type I ~ V by 1 or 2, and type VI that has the round-shaped ground. But the time differences among the types are not known yet. For the burial appliances of square-shaped moated burial precincts, there are stone coffins, pit burials and jar burials. The major burial appliances situated in the mound are stone coffins and pit burials, and jar burials are subsidiary appliances that were buried at the shoulder part of the mound or at precincts. According to the case of Gwanchang-ri KM423, grave mounds, which arc closely related with the burial appliances, were built by heaping up the earth in and around the precinct as low as only enough to protect the burial appliances. Considering the relics unearthed in the burial compartment of KM437, the time when square-shaped moated burial precincts were formed is estimated to be the age when Songguk-ri type earthenware and clay stripes earthenware co-existed. It was the early Iron Age when ironware began to sp read in this country. Emerging first in that age, square-shaped moated burial precincts were presumably formed until around the end of BC or the beginning of AD, when KM404 and KM423, which were unearthed with plain earthenware, grey earthenware and ironware, were formed. When analyzing the form of small-sized graveyards in precincts, the unearthed relics and the locations, the people who formed square-shaped moated burial precincts were considered as those who had a culture comprising clay stripes earthenware, which appears newly in the Songguk-ri type earthenware of native, and ironware, and a settled agricultural society based on paddy fields and labor forces of family units.

• 한국환경농학회지
• /
• 제37권1호
• /
• pp.15-20
• /
• 2018

상승온도 처리에 따른 논토양 탄소의 변동과 벼 생육을 조사한 결과를 요약하면 다음과 같다. 소형 상부개방형 챔버를 이용하여 대기온도 보다 $0.4^{\circ}C$, $0.5^{\circ}C$, $0.9^{\circ}C$ 상승온도 환경을 조성하여 상승온도를 처리할 수 있었다. 사각챔버의 내부온도는 대기보다 평균온도와 최고온도가 높고 최저온도는 낮은 특징을 나타내었다. 상승온도 처리구의 포트 내 표면수의 TOC 농도는 대조구 보다 상승온도 처리구에서 높았고 시간이 경과함에 따라 점차 낮아졌다. 벼 재배후 토양의 TOC 함량은 대조구 보다 상승온도 처리구에서 낮았다. 상승온도 처리로 벼 식물체의 탄소함량은 감소하고 질소함량은 증가하여 C/N 율은 감소하는 경향을 나타내었다. 상승온도 처리로 대조구 보다 벼의 줄기 길이와 줄기무게가 유의하게 증가하였으나 이삭수와 벼 낱알 무게는 유의한 차이를 나타내지 않았다.

• 농업과학연구
• /
• 제10권1호
• /
• pp.61-73
• /
• 1983

경지(耕地)의 이용율(利用率)을 높이면서 식량작물(食糧作物)의 증산(增産)을 위하여 현행작부체계(現行作付體系)를 개선(改善)할 기초자료(基礎資料)를 얻고자 충남지방(忠南地方)을 도시근교(都市近郊)(대덕(大德) 천원군(天原郡)), 평야지역(平野地域)(논산(論山) 당률군(唐律郡)), 해안지역(海岸地域)(서산(瑞山) 보령군(保寧郡)), 및 산간지역(山間地域)(공주(公州) 청양군(靑陽郡))으로 구분(區分)하여 각(各) 지역별(地域別)로 10호(戶)의 농가(農家)를 선정(選定) 계(計)400호(戶)의 농가(農家)에 대(對)하여 1982년(年)에 재배(栽培)한 전답(田沓)의 작부양식(作付樣式)과 그 이용(利用) 상황(狀況)을 조사분석(調査分析)하였는데 그 결과(結果)를 다음과 같이 요약(要約)한다. 1) 밭의 평균이용율(平均利用率)은 161.9%이었는데 평야지역(平野地域)은 188.9%로 그 이용율(利用率)이 가장 높았고 도시근교(都市近郊)는 152.0%로 가장 낮았다. 2) 밭에서 재배(栽培)된 작목수(作目數)는 32종(種)이었는데 밭의 총식부면적중(總植付面積中) 콩의 재배면적(栽培面積) 비율(比率)이 18.8%로서 가장 높았고 다음은 보리가 15.4%, 고추는 13.1% 그리고 배추가 10.1% 등이었으나 도시근교(都市近郊)에서는 고추, 평야지역(平野地域)과 해안지역(海岸地域)에서는 콩, 산간지역(山間地域)에서는 보리의 재배면적비율(栽培面積比率)이 가장 높았다. 3) 논의 평균이용율(平均利用率)은 115.6%이었는데 도시근교(都市近郊)는 140.0%로 그 이용율(利用率)이 가장 높았고 해안지역(海岸地域)은 108.2%로서 가장 낮았다. 4) 논에서 재배(栽培)된 작목수(作目數)는 12종(種)이었는데 수도(水稻)를 제외(除外)하면 보리의 재배면적(栽培面積)이 가장 넓어서 총식부면적(總植付面積)의 5.0%를 차지하고 있으며 다음은 딸기가 4.0%이었으나 도시근교(都市近郊)에서는 딸기, 기타지역(其他地域)에서는 보리의 재배면적(栽培面積)이 가장 넓었다. 5) 밭의 작부유형(作付類型)은 1년(年)1작형(作型)과 1년(年)2작형(作型)으로 나타났는데 1년(年)2작형(作型)은 다시 작물간(作物間)의 조합(組合)에 따라서 38형(型)으로 분류(分類)되며 기중(其中) 대맥(大麥)+대두형(大豆型)의 재배면적(栽培面積)은 1년(年)2작면적(作面積)의 35.0%를 차지하고 있으나 도시근교(都市近郊)에서는 이 형(型)의 재배면적(栽培面積)이 좁은 반면(反面) 채소류간(菜蔬類間)의 조합면적(組合面積)이 넓었다. 6) 논의 1년(年)2작형(作型)은 다시 6개형(個型)으로 나뉘는데 수도(水稻)+맥류형(麥類型)의 재배면적(栽培面積)이 1년(年)2작면적(作面積)의 42.8%로 가장 높은 비율(比率)을 차지하고 있으나 도시근교(都市近郊)에서는 이 형(型)의 재배면적(栽培面積)이 좁고 수도(水稻)+과채류(果菜類)의 재배면적(栽培面積)이 가장 넓었다. 한편 답이작면적(沓裏作面積)은 1년(年)2작면적(作面積)의 76.3%로서 답전작면적(沓前作面積)보다 현저히 넓었다. 7) 밭의 작부조합(作付組合)에 있어서는 동과(同科) 또는 근록작물(近綠作物)로서 윤작특성(輪作特性)이 근사(近似)한 작물간(作物間)의 불합리(不合理)한 재배조합면적(栽培組合面積)이 19.09ha에 달(達)했다. 8) 밭에서의 식량작물(食糧作物) 재배면적(栽培面積)은 88.92ha인데 반(反)하여 채소류(菜蔬類)는 93.70ha, 그러고 공운작물(工芸作物)이 21.80ha로서 식량작물(食糧作物)의 재배면적(栽培面積)이 채소류(菜蔬類)의 재배면적(栽培面積)보다 좁았다. 9) 1910년(年)부터 1980년(年)까지 연구보고(硏究報告)된 보문중(報文中) 1134건(件)을 분석(分析)한 결과(結果) 우리나라에서의 작부(作付) 체계(體系)에 관(關)한 연구(硏究)는 답이작중심(沓裏作中心)으로 이루어졌고 연구(硏究) 목적(目的)은 14개(個)로 분류(分類)할수 있었는데 파종기(播種期), 파종량(播種量), 시비량(施肥量), 이식기(移植期), 작휴법(作畦法), 파종방법(播種方法) 및 품종선발(品種選拔) 시험(試驗) 등이 대부분(大部分)이었다.

• 한국잡초학회지
• /
• 제7권2호
• /
• pp.208-219
• /
• 1987

최근(最近)에 수도용(水稻用) 제초제(除草劑)로 개발(開發)된 수종(數種)의 신제초제(新除草劑)들의 못자리 및 본답(本畓)의 잡초방제효과(雜草防除效果)와 이들의 작용성(作用性)을 구명(究明)하기 위해 1986년(年) 영남작물시험장(嶺南作物試驗場)에서 일련(一連)의 실험(實驗)을 실시(實施)하였던 결과(結果)는 다음과 같다. 1. 최근(最近) 개발(開發)된 수도용(水稻用) 제초제(除草劑) 중(中)에서 상면진압(床面鎭壓)못자리에서도 벼에 대(對)한 약해(藥害)가 거의 없으면서 제초효과(除草效果)가 우수(優秀)하였던 제초제(除草劑)는 pyrazolate 또는 pyrazoxyfen의 파종전(播種前) 처리(處理)와 quinclorac의 파종후(播種後)10일(日) 처리(盧理)하였다. 2. 이앙답(移秧畓)에서 일년생( 一年生) 및 다년생(多年生) 잡초(雜草)에 대(對)한 살초효과(殺草效果)가 높으면서 벼에 대(對)한 약해(藥害)가 겨의 없었던 처리(處理)는 NC-311와 butachlor 또는 quinclorac와의 혼합처리(混合處理)였는데 이들 혼합처리(混合處理)는 피의 엽기(葉期)가 2.5 엽기(葉期)까지도 90% 이상(以上)의 살초효과(殺草效果)를 보였으며 NC-311 + quinclorac의 혼합방법(混合方法)이 NC-311 + butachlor의 혼합방법(混合方法)보다 높은 살초력(殺草力)을 유지(維持)하였고 살초력(殺草力)을 유대(維待)하였고 살초력(殺草力) 지속기간(持續期間)도 길었다. 3. pyrazolate와 sulfonyl urea계(系) 제초제(除草劑)인 DPX-5384, CGA 142464, NC-311은 벼에 대(對)한 안전성(安全性)이 대단(大端)히 높았는데 지상부(地上部) 생육(生育)보다는 지하부(地下部) 생육억제영향(生育抑制影響)이 높은 경향(傾向)이었고, 이들 제초제(除草劑)에 대(對)한 품종간(品種間) 반응(反應)에 있어서도 일본형(日本型) 품종(品種)인 낙동(洛東)벼가 통일형(統一型) 품종(品種)보다 민감(敏感)한 반응(反應)을 보였다. 4. 이들 제초제(除草劑)의 흡수부위(吸收部位) 영향에 있어서는 벼의 경우 흡수부위(吸收部位)에 관계(關係)없이 大端(대단)히 안전(安全)하지만 피에 대(對)해서는 sulfonyl urea계(系)의 경우는 유아부(幼芽部) 흡수(吸收)가, pyrazolate와 Quinclorac의 경우는 유근부(幼根部) 흡수(吸收)가 주흡수(主吸收) 경로(經路)가 되었으며 피에 대(對)한 살초효과(殺草效果)는 Quinclorac이가장 탁월(卓越)하였다.