• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2656-2658
• /
• 1999

This paper presents a control scheme for a three-phase PWM converter system without any voltage sensors. Two input currents and one load current are measured. In a general PWM converter system, the required AC input and DC output voltage values in order to control the converter are estimated using the differential equations of the converter from the measured input currents and load current values in the switch modes of the converter circuit. The PI controller is used as DC voltage controller and sinusoidal tracking controller which tracks directly AC input current is used as input current controller. The Proposed method is verified by simulations. This paper describes the estimation method and configuration of the controller, and discusses steady state and transient performances of the converter

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2534-2536
• /
• 1999

This paper suggested a new sensorless driving strategy for brushless de motor which can improve the conventional degradation of highspeed operating performances, lowspeed operating performances and starting performances caused by applying general single pwm switching frequency. By varying PWM switching frequency during operating time, the proposed method can get some desired upper performances. For confirming the validity of the proposed method, the sensorless driving system is implemented with an rPM module and 87c196MC micro controller.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.8
• /
• pp.1544-1550
• /
• 2009

In this paper, a new single phase voltage sag/swell compensator using direct power conversion is proposed. A new compensator consists of input/output filter, series transformer and direct ac-ac converter, which is a single-phase back-to-back PWM converter without dc-link capacitors. Advantages of the proposed compensator include: simple power circuit by eliminating dc link electrolytic capacitors and thereby, improved reliability and increased life time of the entire compensator; simple PWM strategy or compensating voltage sag/swell at the same time and reduced switching losses in the ac-ac converter. Further, the proposed scheme is able to adopt simple switch commutation method without requiring complex four-step commutation method that is commonly employed in the direct power conversion. Simulation and experimental results are shown to demonstrate the advantages of the new compensator and PWM strategy. A 220V, 3kVA single-phase compensator based on the digital signal processor controller is built and tested.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.77-85
• /
• 2009

With the advent of power semiconductor switching devices, power electronics relating to high frequency electromagnetic eddy current based induction heating technology have become more suitable and acceptable. This paper presents high-frequency induction heating cooking appliance circuit based on the zero current switching-PWM single ended push-pull(ZCS-PWM SEPP) resonant inverter added AC-DC converter. This inverter uses pulse-width-modulation(PWM) control method with active auxiliary quasi-resonant lossless inductor snubbers and a switched capacitor. To improved the transient performance, the PI controller is applied for this system. For the systematic parameter optimization of the PI controller, the gradient-based optimization algorithm is applied. The performance of optimized parameters is evaluated using simulation and experimental test. These results show that the proposed systematic optimal tuning method improve the transient performances of this system.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.2
• /
• pp.69-74
• /
• 2004

In general the surge pressure generated in hydraulic systems causes noise, vibration and odd effect to the system. To reduce the surge pressure, high frequency PWM control of 20KHz was attempted. To estimate the braking noise caused by surge, a vehicle equipped with on-board ABS hydraulic modulator has been experimented with respect to the various breaking condition. Thorough this experiments, it was found that breaking noise has been reduced using high frequency PWM control method compare with low frequency method. To evaluate high frequency control m practice, including verification of general functionality, EMI tests was experimented. Its was found that it is necessary to have the solution to electromagnetic interference(EMI) generated by switching elements.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.2
• /
• pp.117-125
• /
• 2016

In this paper, the inverter switch losses of BLDC motor for three types of PWM methods and power devices were analyzed. When the BLDC motor is driven at low currents, the inverter switch losses for MOSFET are low because MOSFET operates like resistance. However, the inverter switch losses for IGBT are higher than MOSFET due to its large turn-off losses. Moreover, synchronous rectification switching method is adaptable because MOSFET has 2-channel. So, MOSFET can be driven with more low impedance and losses. For low power inverter with MOSFET, the power losses of unified PWM are lower than that of unipolar and bipolar PWM. Proposed method and losses analysis results are verified by examination and simulation using Matlab/Simulink.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.3
• /
• pp.252-258
• /
• 2010

If the speed measurement of resolver and the generation of PWM signals are implemented with single microcontroller, it is easy to reduce the system cost and to avoid the switching noise of inverters. To avoid the switching noise and to improve the accuracy of measurement, PWM switching and A/D sampling of the resolver should be synchronized. Phase angle of the resolver excitation signal is increased in stepwise manner, then, the output signal of the resolver is measured in each step. From the measured data, the optimal phase angle of resolver excitation signal is estimated using the least square approximation method.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.8
• /
• pp.529-535
• /
• 2000

In this paper, a current control system of a single phase PWM AC/DC converter using a reduced-order Luenberger observer without source voltage sensors is proposed. The sinusoidal input current and unity input power factor are realised based on the estimated source voltage performed by the reduced-order Luenberger observer using actual currents and DC link voltage. The poles of the reduced-order Luenberger observer are placed in the left half plane of s-plane by the pole-placement method in order to acquire the stability of the observer. The magnitude and the phase of the estimated source voltage are used to accomplish the unity power factor. The proposed method is implemented by DSP(Digital Signal Processor). Experimental Results verify that the reduced-order observer estimates the source voltage without the estimation error and the control system accomplishes the unity power factor, and constant DC link voltage.

• Journal of Power Electronics
• /
• v.9 no.1
• /
• pp.124-131
• /
• 2009

This paper presents a PWM dc-ac converter regulation using a Single Input Fuzzy PI Controller (SIFPIC). The SIFPIC is derived from the signed distanced method, which is a simplification of a conventional fuzzy controller. The simplification results in a one-dimensional rule table, that allows its control surface to be approximated by a piecewise linear relationship. The controller multi-loop structure is comprised of an outer voltage and an inner current feedback loop. To verify the performance of the SIFPIC, a low power PWM dc-ac converter prototype is constructed and the proposed control algorithm is implemented. The experimental results show that the SIFPIC performance is comparable to a conventional Fuzzy PI controller, but with a much reduced computation time.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1211-1213
• /
• 2003

A pulse width modulation(PWM) method for single-phase Sepic-type rectifier is introduced in this paper. The characteristics of the proposed PWM system are high performance high power factor with low input current harmonic distortion. The proposed control method is based on the average-current-mode using the dedicated integrated circuit UC3854 this technique it is possible to implement a very simple control circuit for unitary power-factor in CCM operation and also to provide over-current protection.