• 한국산학기술학회논문지
• /
• 제19권6호
• /
• pp.147-153
• /
• 2018

이중유화법을 통하여 BSA 수용액을 봉입하는 PLGA 마이크로캡슐 입자를 제조하였다. 마이크로캡슐 입자 외부의 수용액 상에서는 입자 표면의 경화를 위하여 유화제를 금속염으로 대체하였다. 제조한 마이크로캡슐 입자에 대하여서 모폴로지, 입자직경 BSA 봉입효율 및 in-vitro 방출실험을 수행하였다. 전자현미경(SEM) 촬영을 통하여 마이크로캡슐 입자는 매끄러운 표면의 특성을 지녔으며 $1-7{\mu}m$ 범위의 직경을 갖는 것이 확인되었다. 마이크로캡슐 입자의 모폴로지는 주로 일차 유화액 내 내부 수용액 대비 고분자 용액의 부피 비 그리고 입자 외부 수용액에서의 금속염의 농도에 직접적인 영향을 받았다. 또한 이러한 요소는 단백질 봉입효율과 in-vitro 방출에도 일부 영향을 미쳤다. 본 실험에서 제조한 마이크로캡슐 입자는 in-vitro 방출 실험에서 초기에 높은 유속의 방출 현상을 보였다. 그렇지만 본 연구에서 제조한 마이크로캡슐 입자는 다른 연구의 결과에 비해 긴 기간 동안의 방출을 보였다. 이상의 결과를 통해 2가의 금속염이 마이크로캡슐 입자의 제조에서 유화제를 대체할 수 있는 좋은 방편이 될 수 있다는 결론을 내릴 수 있었다.

• Membrane and Water Treatment
• /
• 제7권2호
• /
• pp.101-113
• /
• 2016

In this study, to improve the water flux of porous hydrophobic membranes, various water-soluble polymers including neutral, cationic and anionic polymers were adsorbed using 'salting-out' method. The adsorbed hydrophobic membrane surfaces were characterized mainly via the measurements of contact angles and scanning electron microscopy (SEM) images. To enhance the durability of the modified membranes, the water-soluble polymers such poly(vinyl alcohol) (PVA) were crosslinked with glutaraldehyde (GA) and found to be resistant for more than 2 months in vigorously stirred water. The water flux was much more increased when the ionic polymers used as the coating materials rather than the neutral polymer and in this case, about 70% of $0.31L/m^2{\cdot}h$ (LMH) to 0.50 LMH was increased when 300 mg/L of polyacrylamide (PAAm) was used as the coating agents. Among the cationic coating polymers such as poly(styrene sulfonic acid-co-maleic acid) (PSSA_MA), poly(acrylic acid-comaleic acid) (PAM) and poly(acrylic acid) (PAA), PSSA_MA was found to be the best in terms of contact angle and water flux. In the case of PSSA_MA, the water flux was enhanced about 80%. The low concentration of the coating solution was better to hydrophilize while the high concentration inclined to block the pores on the membrane surfaces. The best coating condition was found: (1) coating concentration 150 to 300 mg/L, (2) ionic strength 0.15, (3) coating time 20 min.

• 멤브레인
• /
• 제9권3호
• /
• pp.163-169
• /
• 1999

투과증발 공정을 이용한 알코올/물 혼합물의 분리 시 투과성분/투과성분, 투과성분/막간의 상호인력이 전체적인 투과거동에 어떠한 영향을 미치는지 연구하였다. 사용한 막은 poly(vinyl alcohol)을 glutaraldehyde 로 가교한 막을 사용하였다. 일련의 알코올은 분자량 크기 순서대로 methanol, ethanol, 1-propanol, 1-butanol을 사용하였으며, 조성은 70~97 wt% , 온도는 30, 40, 5$0^{\circ}C$로 변화시키면서 실험하였다. 투과속도는 알코올 함량이 높은 영역에서는 methanol 수용액이 가장 높았으며 ethanol, 1-propanol, 1-butanol 수용액 순으로 감소하였다. 그러나 물의 함량이 어느 정도 높아지면 이런 현상은 완전히 역전되어 1-butanol 수용액의 투과속도가 가장 높으며 1-propanol, ethanol, methanol 수용액 순으로 투과속도 크기를 보였다. 이러한 현상을 공급액의 조성에 따른 막과 투과성분간의 상호인력, 투과성분과 투과성분간의 상호인력 등의 영향의 관점에서 분석하였다.

• 한국전기전자재료학회논문지
• /
• 제32권4호
• /
• pp.333-340
• /
• 2019

The effects of compaction methods on the sintering density, microstructures, and mechanical properties were investigated in ${\alpha}-alumina$ ceramics. ${\alpha}-Alumina$ powders were granulated with a 10% aqueous solution of polyvinyl alcohol (PVA). Uniaxially pressed (UAP) and cold isostatic-pressed (CIP) samples were prepared by pressing uniaxially at a pressure of 1 ton for 1 min, and isostatically at 200 MPa for 15 min, respectively. Subsequently, both types of samples were sintered at $1,200^{\circ}C$, $1,300^{\circ}C$, $1,400^{\circ}C$, $1,450^{\circ}C$, $1,500^{\circ}C$, $1,550^{\circ}C$, and $1,600^{\circ}C$ at a rate of $5^{\circ}C/min$ for 2 h. The CIP samples were better than the UAP samples for all properties measured, such as the sintering density, Vicker's hardness, and toughness. The CIP sample sintered at $1,400^{\circ}C$ showed the maximum Vicker's hardness and toughness; this may be attributed to the competing effects of a decrease in porosity and the growth of grains with increasing sintering temperature.

• 대한치과보철학회지
• /
• 제35권1호
• /
• pp.221-243
• /
• 1997

The objective of this study was to characterize the mechanical properties of $Y_{2}O_{3}$-containing glass infiltrated ceramic core material, which was made by pressureless powder packing method. A pure alumina powder with a grain size of about $4{\mu}m$ was packed without pressure is silicon mold to form a bar shaped sample, and applied PVA solution as a binder. Samples were sinterd at $1350^{\circ}C$ for 1 hour. After cooling, $Y_{2}O_{3}$-containing glass($SiO_{2},\;Y_{2}O_{3},\;B_{2}O_{3},\;Al_{2}O_{3}$, ect) was infiltrated to the sinterd samples at $1300^{\circ}C$ for 2 hours and cooled. Six different proportions $Y_{2}O_{3}$ of were used to know the effect of the mismatch of the thermal expansion coefficient between alumina powder and glass. The samples were ground to $3{\times}3{\times}30$ mm size and polished with $1{\mu}m$ diamond paste. Flexural strength, fracture toughness, hardness and other physical properties were obtained, and the fractured surface was examined with SEM and EPMA. Ten samples of each group were tested and compared with In-Ceram(tm) core materials of same size made in dental laboratory. The results were as follows : 1. The flexural strengths of group 1 and 3 were significantly not different with that of In-Ceram, but other experimental groups were lower than In-Ceram. 2. The shrinkage rate of samples was 0.42% after first firing, and 0.45% after glass infiltration. Total shrinkage rate was 0.87%. 3. After first firing, porosity rate of experimental groups was 50%, compared with 22.25% of In-Ceram. After glass infiltration, porosity rate of experimental groups was 2%, and 1% in In-Ceram. 4. There was no statistical difference in hardness between two materials tested, but in fracture toughness, group 2 and 3 were higher than In-Ceram. 5. The thermal expansion coefficients of experimental groups were varied to $4.51-5.35{\times}10^{-6}/^{\circ}C$ according to glass composition, also the flexural strengths of samples were varied. 6. In a view of SEM, many microparticles about $0.5{\mu}m$ diameter and $4{\mu}m$ diameter were observed in In-Ceram. But in experimental group, the size of most particles was about $4{\mu}m$, and a little microparticles was observed. The results obtained in this study showed that the mismatch of the thermal expansion coefficients between alumina powder and infiltrated glass affect the flexural strength of alumin/glass composite. The $Y_{2}O_{3}$-containing glass infiltrated ceramic core made by powder packing method will takes less time and cost with sufficient flexural strength similar to all ceramic crown made with slip casting technique.

• 대한화학회지
• /
• 제19권4호
• /
• pp.269-279
• /
• 1975

合成한 pllyglyceryl phthalate, bisphenol A-epichlorohydrin 축중합물과 polyvinyl alcohol의 naphthoquinone-1,2-diazide-5-sulfonyl esters(PGND, BEND 및 PVAND)의 感光特性을 지배하는 諸因子를 이들에 대한 光照射前後의 溶解度 차이에 의하여 檢討하였다. 유리 또는 石英支持薄板上에 塗布한 各試料를 各種條件下에서 露光하고 알카리 水溶液에 침지시킨 다음 塗布된 필림의 殘膜收率(W/W0)을 計算하였다. 필름의 感光度와 직접적인 관계가 있는 殘膜收率은 母體樹脂의 重合度, 增感劑의 種類 및 添加濃度에 따라 영향이 있었다. 母體樹脂의 重合度가 크면 클수록 感光性이 더 우수하였으며, 增感劑의 添加濃度는 5%일때가 가장 좋은 效果를 나타내었다. PGND, BEND 및 PVAND에 대해 본실험에서 사용한 各種 增感制 중에서 가장 效果的인 것은 benzanthrone, 5-nitroacenaphthene, picramide이였다. 이들 樹脂와 增感劑를 添加한 경우의 固相에 있어서의 紫外線吸收스펙트럼과 感色性 寫眞을 각각 비교 검토하여 그 增感과 分光感度的 特性을 糾明하였다. PGND, BEND 및 PVAND는 使用한 增感制에 의하여 光學增感하였으며 增感效果가 현저한 것일수록 그 感光波長城이 長波長쪽으로 伸張하였다. 未增感, 增感試料에 있어서 分光吸收 極大 波長城과 分光感光極大波長城이 거의 一致하고 있는 점으로 보아 試料 樹脂들에 의해서 吸收된 波長城의 光은 그 分野에 有效하게 使用되고 있음을 확인하였다

• Asian-Australasian Journal of Animal Sciences
• /
• 제17권5호
• /
• pp.612-616
• /
• 2004

This study was carried out to compare the semen characteristics, frozen-thawed sperm viability and testosterone concentration and in vitro fertilization (IVF) and development of in vitro matured pig oocytes between two Yorkshire boars. Semen and blood samples were collected once per week from October to November 2002 from two adult Yorkshire boars at 18 months of age with 170 kg body weight. Sperm were deep frozen in 5 ml maxi-straws with lactose-egg yolk and N-acetyl-D-glucosamine (LEN) diluent and stored in liquid nitrogen. Blood samples were obtained at 10 a.m. by inserting a 21 gauge, hypodermic needle attached to 10 ml syringe into surface veins in the ear. The concentration of testosterone was determined by Competitive Enzyme Immunoassay. Ovaries were collected from prepubertal gilts at a local slaughter house. Cumulus oocyte complexes were aspirated from antral follicles (3 to 6 mm in diameter). The medium used for oocyte maturation was modified TCM 199. After about 22 h of culture, oocytes were cultured without cysteamine and hormones for 22 h at $38.5^{\circ}C$, 5% $CO_2$ in air. For IVF, one frozen 5 ml straw was thawed at $52^{\circ}C$in 40 sec and was diluted with 20 ml Beltsville thawing solution at room temperature. Sperm were washed 2 times in mTLP-PVA and inseminated without preincubation after thawing. Oocytes were inseminated with $2{\times}10^7$/ml sperm concentration. Oocytes were coincubated for 6 h in 500 ${\mu}$l mTBM fertilization medium. At 6 h after IVF, oocytes were transferred into 500 ${\mu}$l NCSU-23 culture medium for further culture of 48 and 144 h. There were no significant differences in the semen volume, motility, normal acrosome morphology and sperm concentration of raw semen between A and B of Yorkshire boar. However, motility and normal acrosome of boar A were higher than those of boar B at 0.5, 2, 3, 4, 5 and 6 h incubations of frozen-thawed sperm. Testosterone concentration (3.75 ng/ml) of boar A was higher than that (2.34 ng/ml) of boar B. The rate of blastocyst formation (15.1%) of boar A was higher than that (10.4%) of boar B. In conclusion, serum testosterone concentration of boar showed very important role for the frozen-thawed sperm viability and the blastocyst formation of pig oocytes matured in vitro.

• 분석과학
• /
• 제19권6호
• /
• pp.482-489
• /
• 2006

Pediococcus에서 추출된 lactate oxidase(LOD)를 poly(vinyl alcohol)(PVA)에 고정화하여 2전극계로 구성된 lactate 바이오센서를 제조하였다. Lactate는 LOD 효소와의 반응에서 생성되는 $H_2O_2$를 전기화학적으로 금(Au)위에 형성시킨 Pt-black 층에서 산화시켜 정량 할 수 있었다. Pt-black으로 만들어진 센서는 과산화수소에 대해서 낮은 전위(+300 mV vs. Ag/AgCl)에서 큰 산화전류를 보여주었으며, ascorbic acid, acetaminophen, uric acid 등과 같이 산화되기 쉬운 산화 종들의 영향을 감소시켜주었다. 외부보호막으로는 다양한 종류의 친수성 폴리우레탄을 사용하였다. 센서는 in vitro 방식으로 흐름계와 비흐름계 모두에서 성능을 평가하였다. 제작된 센서는 0.05 M NaCl을 포함하는 0.05 M 인산염 완충용액(pH 7.6)에서 성능을 시험하였으며, 0.1 mM에서 9.0 mM의 lactate 농도구간에서 직선적 감응성을 나타내었다. 최적화된 센서는 $4^{\circ}C$ 완충용액에 보관하였으며, 25일 이상 감응도(sensitivity)가 거의 변화하지 않았다.