• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.5
• /
• pp.169-179
• /
• 2019

During the initial design stage of apartment complex, the photovoltaic(PV) system has been considered as an alternative of renewable energy system and planned to install at the rooftop floor level in general. The electric power generation characteristics can be influenced by the block layout, building orientation and roof top structure because of azimuth angle, tilt angle, and partial shading. This study aims to investigate power generation characteristics of photovoltaic system in apartment buildings by considering the partial shading conditions due to the block layout, building orientation and roof-top structures. For the photovoltaic module arrangement planning in rooftop floor level, shading areas were firstly analyzed due to the adjacent building structure. And the annual and seasonal power generation of PV system were analyzed through the PVsyst simulation results. The results show that shading period at the roof top surface can be increased due to the parapet and water tank. Initial design power capacity can be decreased by considering the daily insolation period and distance between PV modules through the shading simulation. As the number of PV modules decreases, the annual power generation can be decreased. However annual power generation per unit area of PV modules can be increased and performance ratio can be increased above 80%. Also the power generation of PV system can be critically affected by building orientation and the performance ratio can be drastically decreased in east-oriented buildings due to the shading problems caused by adjacent structures at roof top level such as parapet and water tank.

• Proceedings of the KIEE Conference
• /
• 2008.11a
• /
• pp.503-505
• /
• 2008

Photovoltaic(PV) resource connected in the power system can be affect to the power quality. To analyze the power quality, this paper simulate the variation of power factor by PV resource connected to the low voltage system. The power factor calculator and full-bridge inverter of PV system are modeled by EMTP/MODELS. Simulation results according to the PV capacity and load are presented.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.103-104
• /
• 2015

Solar energy has proven to be a potential clean energy source to help offset the large consumption of fossil. Nowadays, many research projects aim to enhance photovoltaic (PV) system performance and functionality. This research focuses on integrating self-monitor capability into dc-dc converters that control PV panels to detect a fault in series-connected PV cells, called hot spotting. A detection method using ac parameter characterization is proposed and its operation is examined through simulation.

• Current Photovoltaic Research
• /
• v.5 no.3
• /
• pp.89-94
• /
• 2017

We have examined the issues on the measurement of bifacial photovoltaic(PV) devices that should be considered in order to ensure a measurement accuracy beyond a certain level and the comparability between the bifacial PV devices. Based on the results of various experiments and previous studies, solutions for these measurement issues are suggested. The most significant technical issues in the performance measurement of the bifacial PV devices are 1) elimination of the effect due to the light reflection on the sample holder surface and 2) the measurement of the expected power generation gain in outdoor operation. The effect due to the light reflection on the sample holder surface can be eliminated by using an anti-reflective sample holder. In case of a reflective sample holder, if the bifacial device have a linear characteristic with respect to the irradiance of incident light, it has been confirmed (through some previous studies and additional experiment) that exact measurement results can be obtained by the correction of the measurement data. In addition, it was also confirmed that the expected power generation gain in the outdoor operation can be obtained by three different methods along with the basic concepts of the bifaciality coefficient, the albedo, and the effective front irradiance.

• Current Photovoltaic Research
• /
• v.9 no.2
• /
• pp.45-50
• /
• 2021

Agrovoltaic system is a concept that combines agriculture and photovoltaic (PV) system by applying a PV system to the upper part of farmland. In this study, we developed a folding drive system for an agrophotovoltaic (agroPV) module (150 Wp/4×9 cell) exclusively for pear farming with 10 kW capacity. The system was installed in 2018, and the growth characteristics and quantity of pears under the agroPV folding system have been investigated for 2 years. We found that thare is no differences of the characteristics of pears grown under the agroPV system compared to the pears grown without the system (control) except the percutaneous color L of pear. However, the weight and sugar content of the pear grown under the agroPV system were decreased by 4.5% and 1.3°Bx compared to that of the control, respectively. We assume that this is mainly due to the influenced of the delay in flowering as upper PV module block some of sunlight. However, interestingly, when we deleyed the pear harvesting by 2 weeks, the weight of pears increased by 8.5% and they became nearly the sample as the control pears harvested 2 week earlier. In addition, we also found that the agroPV modules decrease the fall rate of pear when the typoon struck, also it mitigates cold damage by 38% during April by protecting from frost. In conclusion, it can be said that the agroPV system help to protect target crops from the environmental conditions and the quality of the crops are similar to the that of control.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.4
• /
• pp.480-485
• /
• 2012

Use of photovoltaic (PV) power generation system will become more widespread in the future due to anticipated cost reduction in PV technology. As the capacity of PV systems increases, a variation of power system frequency may prevent the stable output of PV system. However, the standard for the frequency protection of distributed generation in Korea Electric Power Corporation (KEPCO)'s rule does not include the setting of frequency protection. Therefore, this paper analyzes the correlation between the frequency protection requirements and the stability of grid-connected PV system for the adjustable operating setting of frequency protection. The distribution system interconnected with 3 MW PV system is modeled by Matlab/Simulink. The various values of frequency are simulated. For studied cases, the stability of PV system is analyzed. It is concluded that the setting of frequency protection is necessary to consider the stability of PV system.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1306-1307
• /
• 2011

Recently, the small scale photovoltaic (PV) electronic devices are drawing attention as the upcoming PV generation system. The PV system is commonly used in small scale PV applications such as LED lighting and cell phone. This paper proposes photovoltaic output sensorless (POS) maximum power point tracking (MPPT) control for a small scale charging system of PV-nickel metal hydride battery using field-programmable gate array (FPGA) controller. A converter is connected to a small scale PV cell and battery, and performs the POS MPPT at the battery terminal current instead of being at the PV cell output voltage and current. The FPGA controller and converter operate based on POS MPPT method. The experimental results show that the nickel metal hydride battery is charged by the maximum PV output power.

• Current Photovoltaic Research
• /
• v.2 no.3
• /
• pp.140-145
• /
• 2014

The globally used PV qualification tests and reports the pass/fail only. Therefore, the reliability of new PV materials and parts can't be compared quantitatively with the reliability of the PV parts and materials in the market. Global PV materials and parts companies test and compare their materials, parts, and modules using the failure-to-test (FTT). However, it takes a long accelerated stress test (AST) until failure. It also needs to test the new and existing materials and parts. Therefore, it requires excessive equipment time and cost. In order to reduce the time and cost, a new reliability enhancement methodology has been developed. It tests the PV materials, parts, and modules in the global market and stores them in the PV reliability database. It reduces the time and cost of the comparison and enhancement of PV reliability. An example of the reliability enhancement of the PV encapsulant, EVA is presented.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.1
• /
• pp.80-84
• /
• 2012

Recently, the small scale photovoltaic (PV) electronic devices are drawing attention as the upcoming PV generation system. The PV system is commonly used in small scale PV applications such as LED lighting and cell phone. This paper proposes photovoltaic output sensorless (POS) maximum power point tracking (MPPT) control for a small scale charging system of PV-nickel metal hydride battery using field-programmable gate array (FPGA) controller. A converter is connected to a small scale PV cell and battery, and performs the POS MPPT at the battery terminal current instead of being at the PV cell output voltage and current. The FPGA controller and converter operate based on POS MPPT method. The experimental results show that the nickel metal hydride battery is charged by the maximum PV output power.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2148-2153
• /
• 2007

The electricity conversion-efficiency of solar cell for commercial application is about 6-15%. More than 85% of the incoming solar energy is either reflected or absorbed as heat energy. Consequently, the working temperature of the photovoltaic cells increases considerably after prolonged operations and the cell's efficiency drops significantly. PV/T refers to the integration of a PV module and a solar thermal collector in a single piece of equipment. By cooling the PV module with a fluid steam like air or water, the electricity yield can be improved. At the same time, the heat pick-up by the fluid can be to support space heating or service hot-water systems. In this study, a pulsating heat pipe solar heat collector was combined with single-crystal silicon photovoltaic cell in hybrid energy-generating unit that simultaneously produced low temperature heat and heat and electricity. This experiment was investigating thermal and electrical efficiency for evaluation of a PV/T system.