• Fibers and Polymers
• /
• v.5 no.3
• /
• pp.239-244
• /
• 2004

Solution-cast films of polymethylmethacrylate (PMMA) and polyurethane (PU) containing polymeric styryl dye up to 5 % by weight were prepared to investigate their acid-sensitivity and mechanical and thermal properties. Original red samples due to styryl dye turned out yellow very rapidly as they were exposed to acid vapor of hydrochloric acid or p-toluenesulfonic acid. According to UV/VIS spectroscopic measurements, characteristic peak intensities near 430 nm and 520 nm increased or decreased relatively with exposed amounts of acid, respectively. Both PMMA and PU samples showed uniform color distribution due to a good miscibility between polymer and dye which can be evidenced by measurements of glass transition temperature. No significant difference in acid-sensitivity was found between PU and PMMA except relative absorbance. However, dependence of their mechanical properties on dye content was somewhat different with PU or PMMA. In case of PMMA, modulus and breaking stress increased up to about 50 % with increasing dye content, whereas those of PU samples showed only slight increase. It was ascribed to whether the matrix polymer was in the glassy or rubbery state.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.6
• /
• pp.87-92
• /
• 2013

This paper focuses on analyzing the effects of primary user (PU) signal arrival on the local spectrum sensing performance. The probability for signal arrival at a sample in the sensing time is uniformly distributed in the sensing time. We first analyze the main factor that causes the degradation in the detection results in the conventional energy detection (CED) under the uniformly random arrival of the PU-signal. Thus we propose an approach in order to enhance the detection performance, in which an estimator which detects the arrival of the PU signal cooperates with a composite energy detection. The mathematical analysis and numerical simulation has validated the outperformance of the proposed approach compared to the CED.

• Journal of Communications and Networks
• /
• v.15 no.5
• /
• pp.514-526
• /
• 2013

With a long sensing period, the inter-frame spectrum sensing in IEEE 802.22 standard is vulnerable to the effect of the traffic of the primary user (PU). In this article, we address the two degrading factors that affect the inter-frame sensing performance with respect to the random arrival/leaving of the PU traffic. They are the noise-only samples under the random arrival traffic, and the PU-signal-contained samples under the random leaving traffic. We propose the model in which the intra-frame sensing cooperates with the inter-frame one, and the inter-frame sensing uses the time-of-arrival (ToA), and time-of-leave (ToL) detectors to reduce the two degrading factors in the inter-frame sensing time. These ToA and ToL detectors are used to search for the sample which contains either the ToA or ToL of the PU traffic, respectively, which allows the partial cancelation of the unnecessary samples. At the final stage, the remaining samples are input into a primary user detector, which is based on the energy detection scheme, to determine the status of PU traffic in the inter-frame sensing time. The analysis and the simulation results show that the proposed scheme enhances the spectrum-sensing performance compared to the conventional counter-part.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.104-107
• /
• 2004

In this work, the blend of diglycidylether of bisphenol A (DGEBA) and modified polyurethane (PU) was prepared and characterized in the cure behaviors and mechanical interfacial properties. The N-benzylpyrazinium hexafluoroantimonate was used as a cationic initiator for cure, and the content of PU was varied within 0-20 phr. The cure behaviors and mechanical interfacial properties were studied by DSC, near­IR, and the critical stress intensity actor $(K_{IC})$ measurements. Also thermal stabilities were carried out by TMA and TGA analyses. As a result, the cure activation energy $(E_a)$ and the conversion $(\alpha)$ were slightly increased with increasing the PU content, and a maximum value was found at 10 phr PU. The mechanical interfacial properties measured from $K_{IC}$ showed a similar behaviors with the results of conversion. These results were probably due to the increase of the hydrogen bonding between the hydroxyl groups of DGEBA and isocyanate groups in PU.

• Elastomers and Composites
• /
• v.31 no.2
• /
• pp.104-110
• /
• 1996

The polyurethane was synthesized by the reaction of polycaprolactone diol(Mw 2000), 4,4'-diphenylmethane diisocyanate and 1,4-butanediol as the chain extender. Also, the modified polyurethane polymers based on liquid polybutadiene as a part of soft segment and dimethylolpropionic acid as a chain extender, giving polyurethane with various polarity, were synthesized. The thermal, mechanical, adhesion properties and water contact angles of the polyurethanes were examined. From the result of the water contact angle, the polarity of the acid modified PU containing 6% acid content was unchanged but mechanical and adhesion properties were improved. The water contact angles on polybutadiene modified PU films were increased with increasing polybutadiene content. The mechanical properties of the polybutadiene modified PU were higher than that of acid modified PU. However, the mechanical properties were reduced as polybutadiene content increased. The result is presumably due to phase separation between hard segment and soft segment. The peel strength of the polyurethane introduced with 5wt% polybutadiene was improved about 150% than that of unmodified PU. The same as the mechanical properties, the more polybutadiene was introduced, the lower peel strength was obtained.

• Journal of Biomedical Engineering Research
• /
• v.20 no.6
• /
• pp.547-553
• /
• 1999

생체재료로 사용되는 polyurethane(PU) 표면에 항혈전성 lumbrokinase(LK)를 고정함으로써 생체적합성을 향상시키고자하였다. 먼저 LK를 PU 표면에 고정하기 위한 가교제로서 4-azidoaniline hydrochloride와 poly(acrylic acid)를 이용하여 4-azidophenyl 작용기가 amido 결합으로 치환된 수용성, 광반응성 poly(acrylic acid)(PPa-II)를 합성하였다. H-nuclear magnetic reasonance spectrum(500MHz H-NMR)의 6-7 peak와 infrared spectrum (FT-IR) 의 2125.48 cm peak으로부터 PPA-II의 합성을 지원하였다. EH한 4-azidophenyl 작용기가 poly(acrylid acid) 잔기에 치환된 정도는 UV/VIS adpectrophotometric spectrum을 확인한 결과 11~14%임을 알 수있었다. 0.5 1및 5% PPA-II를 각각 광반응하여 얻은 PU는 39.5, 161.8 및 181.5 nmole/$\textrm{cm}^2$의 농도로 표면에 carvoxyl 작용기가 유도되었음을 알 수있었다. 0.05M KH2PO4 (pH 4.5) 용액에서 1-ethyl-3-(3-(dimethylamino)propyl)carbodiimide(EDC)를 촉매로 사용하여 LK를 PU표면에 amido 공유결합으로 고정하였으며, 이것은 지속적인 fibrinolytic 활성도를 보였다. PPA-II를 이용한 표면 개질 방법은 수용성 반응조건에서 이루어진다는 점과 광반응을 이용함으로써 특정부위에서의 표면개질이 가능하다는 점에서 그 응용가치가 크며 아울러 PU의 생체적합성을 향상시킬 수 있는 방법으로서 판단된다.

• Journal of Korean Society for Quality Management
• /
• v.45 no.4
• /
• pp.769-780
• /
• 2017

Purpose: The aim of this study is to conduct a survey of dimethylformamide(DMF) content in polyurethane(PU)-based consumer products and provide the information for the PU manufacturer and company to prepare a countermeasure for improving the quality competitiveness. Methods: This study selected PU-based consumer products(toddler shoes, children's bag, children's play mat, safety gloves), which is closely used in everyday life, and analyzed the residual DMF content in the consumer products. Results: In this study, it was confirmed that the average DMF content of toddler shoes, children's bag, children's play mat and safety gloves are 38 ppm, 119 ppm, 396 ppm and 826 ppm, respectively. In addition, most of the samples were found to meet the internationally accepted standard of 1,000 ppm and the DMF contents were reduced from at least 63 % to 85 % with a single washing process. Conclusion: The domestic PU manufacturers should seek ways to reduce the DMF through their production facility applications and introducing new materials such as water-soluble PU, and preparing the process development for their quality competitiveness.

• Applied Chemistry for Engineering
• /
• v.3 no.4
• /
• pp.614-619
• /
• 1992

Two types of polyurethane(PU) ionomer dispersion having different type of soft segment, viz. Poly (tetramethylene adipate) glycol(PTAd), and polypropylene glycol(PPG) were emulsion blended. Viscosity of emulsion blend, mechanical, and surface properties of the emulsion cast films were determined as a function of blend composition. Mechanical properties showed a large scatter of data or negative deviation from the additivity rule, and this was attributed to the incompatibility of soft segments. Contact angle measurement indicated that air facing surface of emulsion cast film contained more of PPG PU, due probably to its smaller particle diameter compared to PTAd PU.

• Journal of Korean Medicine Rehabilitation
• /
• v.21 no.3
• /
• pp.71-78
• /
• 2011

Objectives : The purpose of this study is to report the combination effect of Chuna manipulation and warm needle acupuncture for a case of obstinate chronic tinnitus. Methods : We applied Danmuji Anchu Tracton technique, lateral pterygoid Chuna and warm needle acupuncture at SI19 once a day for 2 weeks. Visual analogue scale(VAS) was used for the intensity of tinnitus and tinnitus handicap inventory(THI) was evaluated. Results : VAS was improved from 6 to 2 in right ear, 4 to 1 in left ear after the treatment. THI was also improved from 54 to 34 after the treatmemt. Conclusions : The combined therapy of Chuna manipulation and warm needle acupuncture can be used for chronic tinnitus.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.07a
• /
• pp.81-85
• /
• 2003

PU block polymers are constituted by sequences of constitutional units CU which are : a diisocyanate T, a polyol or a polyamine V, an extensor E .Due to the CU different solubility parameters ,hard and soft micro domains are formed;they can aggregate into different phases. A linear PU can be described by two parameters R=T/N and $R_{E}$=(R-1)V/E.A stoichiometric model is proposed which gives the general formula of all the possible PU: X((TV)$_{k}$(TE)$_{n}$)$_{m}$X , where k and m can be calculated from the experimental molecular weights respectively of pre polymer and polymer and n= R-1.Physical properties depend on PU composition and on nature of CU. I.R. analysis is useful for discovering the hydrogen bonds location : DSC gives informations on the presence of the different phases .PALS analysis shows that nano cavities become tighter on increasing n. A series of particular Pus ,obtained from :TDI, a low molecular weight polyol, a cyclic extensor, at different R and RE was prepared and analysed. These PU are amorphous, monophasic and appear to be good candidates for membranes.nes.nes.