• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.05a
• /
• pp.120-121
• /
• 1993

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2005.05a
• /
• pp.165-165
• /
• 2005

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.36T no.3
• /
• pp.7-12
• /
• 1999

In this paper, dielectric and strain properties of (1-f-y)PMN-yPT-xST ceramics investigated with the amount of $\textrm{SrTiO}^3$(ST). The $\textrm{SrTiO}^3$ content is ranged within 1~6㏖%. Another compositions with excess MgO also investigated. As the amount of ST is increased, dielectric constant has a maximum value at 5㏖% composition. The Curie temperature is decreased linearly with increasing the amount of ST. Coercive field and ramnant polarization has a maximum value at l㏖% composition. As for the effects of excess MgO, the dielectric constant has been increased by the addition of excess MgO up to 3㏖% to a 0.8PMN-0.12PT-0.04ST specimen. But the strain has been decreased by the addition of excess MgO.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.330-330
• /
• 2008

$Fe_2O_3$ added Pb$(Ni_{1/3}Nb_{2/3})O_3-PbTiO_3-PbZrO_3 $ (PNN-PT-PZ) ceramics were produced in order to use them as a bimoph acturator for energy harvesting. Especially, the 0.25 wt% $Fe_2O_3$ added 0.4PNN-0.357PT-0.243PZ, having the composition of morphotropic phase boundary, showed good piezoelectric properties of $d_{33}$ of 810 pC/N, $k_p$ of 77% and $Q_m$ of 55 along with a high Curie temperature of $210^{\circ}C$. A bimorph actuator, composed of the two piezoelectric layers bonded together with a phosphorous bronze layer as a central metallic electrode, was successfully fabricated. The bimorph actuator, vibrated with a 1.3 mm amplitude at 68 Hz, produced high electric power of approximately 60 mW.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.10
• /
• pp.815-820
• /
• 2001

The piezoelectric properties of the PT-PZ-PNN system ceramics were investigated depending on the variati on of the grain size. The grain size was varied by sintering temperature, and additive. The effect of the grain size on the electrical, dielectric, and piezoelectric properties was studied with respect to the feasibility of the application for the piezoelectric transformer. Grain size increased as the PMW contents increased. The smaller the particle size used, the smaller the grain size obtained. Specimens are densily sintered. Dielectric and piezoelectric properties are not always improved in proportion to the grain sizes. When he particle size are fine and the grain size are increased properly with the optimum additives, the piezoelectric preperties have good values. the specimen sintered at 1200$\^{C}$ with PMW 2 mol% and MnO$\_$2/ 0.5wt% contents exhibited good piezoelectric properties for a piezoelectric transformer.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1521-1523
• /
• 2001

In this paper, High quality factor and fine dielectric loss was resulted on specimen added 0.5wt% $MnO_2$ after compared and analyzed dielectric and piezoelectric properties following that added each 0 $\sim$ 0.9wt% of $Fe_2O_3$, $Nb_2O_5$, and $MnO_2$ on dopant at PSN-PT in two material disposition ceramics with research still is not completed to material investigation to increase high power piezoelectric actuator device efficiency. And, a measuring method and the experimental results of the temperature rise under the high vibrational velocity are also described.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1113-1115
• /
• 1993

Piezoelectric Actuator samples were fabricated using PMN-PT-PZ ceramics with Barium substitution, and the strain properties of them were investigated. The tartest Piezoelectric coefficient and electromechanical coupling coefficient were observed at the sintering temperature $1250^{\circ}C$, Barium 5mol%. In the case of Multilayered specimens, they showed considerable strain and small hysteresis than single round type.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1030-1036
• /
• 1994

The ceramics in the system 0.5[Pb(Ni1/3Nb2/3)O3]-0.5[0.65PbTiO3-0.35PbZrO3] were prepared by conventional solid state reaction method, double calcined method (columbite precursor method) and flux method using NaCl-KCl. Amount of pyrochlore phase for the calcined powders, sintering charateristrics, dielectric and piezoelectric properties were then investigated. Sintering temperature was 1000~120$0^{\circ}C$ and in case of flux method, the amount of flux to oxide was 1 : 1 mole ratio. The dielectric and piezoelectric properties of ceramics prepared by double calcined method and flux method were found to be better than those by conventional method. It was also possible to lower sintering temperature and reduce the amount of pyrochlore phase either by double calcined method or flux method. But with increasing sintering temperature, the difference in characteristrics due to diffrent fabrication method gradually.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.4
• /
• pp.620-626
• /
• 1994

As the electrostrictive actuator for optic control, PZN-BT-PT ceramics were investigated for the influences of sintering conditions on the structural, electrostrictive properties and the optical properties of Fabry-perot Interferometer using eletrostrictive ceramics. The specimen SS15T, sintered 1hr at 1150$^{\circ}C$, is sutible for eletrostrictive actuator because its piezoelectric constants(dS131T) and strain(XS131T) at dc 10kV/cm had the higest value of 175${\times}$10S0-12TC/N, -255${\times}$10S0-6TΔl/l respectively. As the dc electric field increased, the interference effect of Fabry-Perot Interferometer was increased. The most intense interference fringe and the maximum power of 160${\mu}$W were observed at dc 6kV/cm. Thus it was considered that specimen SS15T could be used as the electrostrictive actuator for optic control.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.183.2-183
• /
• 2003