• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.182-187
• /
• 2014

As the regulations for Particulate Matter (PM) and Particle Number (PN) emissions from Gasoline Direct Injection (GDI) Vehicle stringent recently, a lot of studies have been made on the emission characteristics of PM and PN. In this study, PM and PN emission characteristics were compared to GDI and Multi Port Injection (MPI) Vehicles using the Condensation Particle Counter (CPC) measurement equipment. And driving mode is divided into normal driving mode (CVS-75, NEDC, NIER 6, NIER 9) and a constant speed driving mode (10 km/h, 35 km/h, 80 km/h, 110 km/h) to evaluate the characteristics in the various operating conditions. In the results, most of the driving mode, PM and PN were emitted from GDI Vehicle more than MPI Vehicle. However, in the constant speed mode of 110 km/h, PM and PN from MPI Vehicle were also a lot of emission. It is determined to cause a difficulty in the fuel injection control of the MPI Vehicle.

• Journal of ILASS-Korea
• /
• v.19 no.3
• /
• pp.142-148
• /
• 2014

In this study, characteristics of gaseous pollutants and particulate matter were investigated on the condition of DPF regeneration and normal DPF condition. THC, CO, $CO_2$, NOx, and $CH_4$ were analyzed by MEXA-7200H and CVS-7100 respectively. Particulate Matter (PM) was measured by difference in weight of Membrane filter. Particle Number (PN) was measured by CPC analyzer. And Sulfate, Nitrate, Organic were measured by Aerosol Mass Spectrometer (AMS). As a result, gaseous pollutants and particulate matter were detected in higher concentration during DPF regeneration than normal DPF condition. And the PN increased by 94%, the fuel consumption was reduced by 29% on DPF generation process. Sulfate, Nitrate and Organic were undetectable level during normal DPF condition. But the highest concentration of Sulfate, Nitrate and Organic were measured as $100{\mu}g/m^3$, $20{\mu}g/m^3$ and $15{\mu}g/m^3$ respectively on DPF regeneration condition. VOCs concentrations (Benzene, Toluene, Ethylbenzene, Xylene) were analyzed by using PTR-MS. Benzene and Toluene emission have little or no change depending on DPF regeneration. But the Ethylbenzene and Xylene have comparatively low emissions on DPF regeneration.

• Journal of ILASS-Korea
• /
• v.17 no.4
• /
• pp.185-191
• /
• 2012

Particulate matters (PM) that is generated by most diesel engine is regulated by the mass concentration measured by the conventional method it had been. Recently, Europe PMP (Particle Measurement Program) decided to start the regulation of vehicle's nano-sized particle number (PN) from the year of 2011 because of nano-particle's higher degree of harm to the human body. So firstly, the standard level of PN emission is introduced in the Euro 5/6 emissions regulation with a limit of $6{\times}10^{11}$ per km for light duty vehicle. Also KPMP(Korea Particle Measurement Program) was organized to copy quickly international technical trend. In this paper, it was investigated the nano-sized PN measurement characteristics for different particle generators between spray type and soot type. And the difference ratio between particle generators, the characteristic of PN concentration, counting efficiency and linearity was analyzed. Then, we make conclusions as followed. When particle diameter is increased, counting efficiency of two generators is decreased. Also Secondary calibration method is more higher 3% than Primary calibration method. Finally, SOF which is included in soot particles is not totally removed so it have great influence on test result of counting efficiency and linearity.

• Journal of the Korean Institute of Gas
• /
• v.20 no.6
• /
• pp.9-15
• /
• 2016

Liquefied petroleum gas (LPG) and compressed natural gas (CNG) are often used as fuel for vehicles because they are clean alternative gas fuels. CNG, as a low-carbon fuel, can contribute to the reduction of greenhouse gas emissions. LPG is often used as fuel for taxis because the performance is almost the same as that of gasoline but the price is lower. In the present study, the exhaust gas and the particle number (PN) of particulate matter, which is a recent environmental issue, were compared between LPG and CNG for the same vehicle. A chassis dynamometer was used to conduct the test according to the Federal Test Procedure (FTP)-75 and Worldwide harmonized Light-duty vehicle Test Procedure (WLTC) modes. The PN values of discharged particles having sizes of 5 nm or larger and 23 nm or larger were measured using two condensation particle counters (CPC). The ratio of carbon dioxide was high in the exhaust gas from the LPG vehicle; the ratio of methane was high in the exhaust gas from the CNG vehicle. The PN values of the emitted particles from the two fuels were similar. The PN values of particles having sizes of 23 nm or smaller were high in the high-speed WLTC mode.

• Clean Technology
• /
• v.26 no.1
• /
• pp.22-29
• /
• 2020

Recently, as the fine dust is increased and the emission regulations of diesel engines have been tightened, interest in diesel soot filtration devices has rapidly increased. There is specifically a demand for the technological development of higher diesel exhaust gas after-treatment device efficiency. As part of this, many studies were conducted to increase exhaust gas treatment efficiency by improving the flow uniformity of the exhaust gas in the diesel particulate filter (DPF) and reducing the pressure drop between the inlet and the outlet of DPF. In this study, the effects of pressure drop by the flow rate and temperature of exhaust gas, DPF I/O ratio, Ash, and PM amount in diesel reduction device were simulated via a 12" diameter DPF and diesel oxidation catalyst (DOC) using ANSYS Fluent. As the flow rate and temperature decreased, the pressure drop decreased, whereas the PM amount affected the pressure drop more than the ash amount and the pressure drop was lower in anisotropic DPF than isotropic DPF. In the case of DPF flow uniformity, it was constant regardless of the various variables of DPF. In ESC and ETC conditions, the filtration efficiency for PM was similar regardless of anisotropic and isotropic DPF, but the filtration efficiency for PN (particle number) was higher in anisotropic DPF than isotropic DPF.

• Journal of ILASS-Korea
• /
• v.24 no.1
• /
• pp.21-26
• /
• 2019

In Korea, Medium-duty trucks are classified into GVW (Gross Vehicle Weight) 3.5~10tons. MDTs are mostly used for logistics or delivery between regions. There have been studied on diesel fuel vehicles for SUVs(Sports Utility Vehicle) or light-duty trucks. But MDTs have been not studied. Therefore, this study have been used MDTs for characteristic exhaust emission. Test was carried out using the certification test mode (NEDC, New European Driving cycle) and the NIER mode in chassis dynamometer of the MDTs. And emission gas was analyzed for PN (Particulate Number), PN size distribution and aldehydes, VOCs (Volatile Organic Compounds), PAHs (Polycyclic Aromatic Hydrocarbons). This paper concluded that EURO-IV trucks produced more MSATs than EURO V trucks. Depending on the engine temperature, more MSATs were generated in cold temperature than in the hot start operation. However, the driving speed, the opposite results was obtained.

• Journal of ILASS-Korea
• /
• v.27 no.2
• /
• pp.94-100
• /
• 2022

Even in non-road UTV (Utility Terrain Vehicle), spark ignition engines are often used to reduce emissions. In this study, gasoline and LPG (Liquified Petroleum Gas) fuels were applied to UTV engines, and the exhaust gas and combustion stability were compared through engine tests. A 0.8-liter two-cylinder SI engine was used in the experiment. Experiments were conducted while changing the IVO (Intake Valve Open) and EVC (Exhaust Valve Close) at 1500 rpm 14 N·m, 40 N·m, and 3000 rpm 17 N·m, 44 N·m conditions. As a result of the experiment, when the valve overlap increased according to the change of IVO and EVC, combustion stability decreased and THC emission increased, but NOx decreased. Comparing the LPG engine with the gasoline engine, the amount of CO₂ and PN (Particulate Number) generation decreased in the LPG engine, and the combustion stability was good.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.4
• /
• pp.351-358
• /
• 2015

In the recent times, the use of gasoline direct injection (GDI) engines has been regarded as a means of enhancing conformance to emission regulations and improving fuel efficiency. GDI engines have been widely adopted in the recent years for their better engine performance and fuel economy compared to those of conventional MPI gasoline engines. However, they present some disadvantages related to the mass and quantity of particulate matter generated during their use. This study investigated the nanoparticle characteristics of the particulate matter exhausted from a GDI engine vehicle installed with different types of gasoline particulate filters, after subjecting it to ultra-lean burn driving conditions. Three metal foam and metal fiber filters were used for each experimental condition. The number concentrations of particles were analyzed for understanding their behavior, and the reduction characteristics were obtained for each type of filter.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.77-83
• /
• 2014

As the interest on the air pollution is gradually risen up at home and abroad, their vehicle emission regulations have been reinforcing by steps. PM regulation was also reinforced 4times for the last 13years and has been applied to SI vehicles after EURO 5. Additionally, knowing that small particles of PM can easily penetrate deep into lungs PM number was added on the regulation from EURO5+ and is applied to CI vehicles. Also, PN regulation is going to be applied to SI vehicles. But, because the regulation is appled to only a general test mode of each countries that is performed at $25{\pm}5^{\circ}C$, it is unclear whether the regulation can work on the other ambient temperature conditions or not. In this paper, to know that exhaust emission characteristics at the special conditions CI vehicles(CRDi w, w/o DPF) were tested using 5-cycle mode, NEDC mode at 5-ambient temperatures (35, 25, 0, -7 and -15) and the exhaust emission test results were discussed. The results show that the vehicle with DPF emits much low PM(and PM number) on all of the test mode. However, NOx of the other mode was emitted higher than regulation mode. Also. NOx was sharply increased according to decreasing Ambient Temperature.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.159-169
• /
• 2016

In this study, the effects of MTBE contents as oxygenates in gasoline on exhaust emissions and fuel economy in MPI and GDi vehicles have been investigated. Various oxygen contents have been selected such as 0, 1.0, 2.3 and 2.7 wt%. FTP-75 and HWFET modes as fuel economy test methods which are widely used in Republic of Korea and US were applied to investigate exhaust emissions from the test vehicles. Emissions of CO, NMHC and NOx did not show significant correlation with oxygen contents in gasoline fuels, although having slight difference with these contents. In addition, CO2 emissions were not significantly changed with respect to oxygen content. But in case of warm-up and FTP-75 and HWFET modes including high speed regimes, CO2 emissions showed inverse correlation with oxygen contents. Particulate number concentration was inversely proportional to the oxygen contents, having the minimum value at the condition of 2.3 wt%. In case of fuel economy through carbon balance method, the highest value has been obtained at 2.3 wt% and there was positive correlation with oxygen contents and fuel economy.