• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.79-85
• /
• 1997

In order to improve the surface characteristics of polymethylmethacrylate(PMMA), oxide thin film coatings were applied using the sol-gel dip-coating technique. The $Si(OC_2H_5)_4$, tetra-ethyl-ortho-silicate(TEOS) was used as a starting material for $SiO_2$ coating. The hardness of the alkoxy-derived oxide-coated PMMA was increased from 190 MPa for non-coated PMMA with increasing film thickness. By optimizing the heating conditions and the hydrolysis conditions, a maximum apparent hardness obtained In the present study was achieved 310 MPa using the withdrawal velocity of 5cm/min and heat treatment at $90^{\circ}C$ for 5 hours, which is about 1.6 times larger than that of uncoated PMMA.

• Laser Solutions
• /
• v.10 no.1
• /
• pp.19-27
• /
• 2007

Previous studies demonstrated that laser ablation under transparent liquid can result in ablation enhancement and particle removal from the surface. Although the ablation enhancement by liquid is already known for semiconductor and metal, the phenomena of polymer ablation have not been studied. In this work, tile liquid-assisted excimer laser ablation process is examined for polymer materials, such as polyethylene terephthalate (PET), polymethyl methacrylate (PMMA) with emphasis on ablation enhancement and surface topography. In the case of PET and PMMA, the effect of liquid is analyzed both for thin water film and bulk water. The results show that application of liquid increases the ablation rate of PMMA while that of PET remains unchanged even in the liquid-assisted process. However, the surface roughness is generally deteriorated in the liquid-assisted process. The surface topography is found to be strongly dependent on the method of liquid application, i.e., thin film or bulk liquid.

• Korean Journal of Optics and Photonics
• /
• v.7 no.4
• /
• pp.357-362
• /
• 1996

The thickness and the spectrum of the complex refractive index in the region 1.5~4.5 eV, of an MNA/PMMA thin film fabricated by spin casting are determined. The film thickness and the refractive index in its transparent region is calculated by modeling the spectroscopic ellipsometry data. The extinction coefficient spectrum is obtained from the absorption spectrum in its non-transparent region. The best fit oscillator parameters of the classical Lorentz oscillator and a quantum mechanical oscillator are found. The complex refractive index spectrum by these oscillators are compared. The present technique can be applied to get the thickness and the complex refractive index of unknown polymer films and thus it will be useful in optical characterization of those films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.3
• /
• pp.135-140
• /
• 2016

In this study, we developed the solution-processed PMMA-$HfO_x$ hybrid ReRAM devices to overcome the respective drawbacks of organic and inorganic materials. The performances of PMMA-$HfO_x$ hybrid ReRAM were compared to those of PMMA- and $HfO_x$-based ReRAMs. Bipolar resistive switching behavior was observed from these ReRAMs. The PMMA-$HfO_x$ hybrid ReRAMs showed a larger operation voltage margin and memory window than PMMA-based and $HfO_x$-based ReRAMs. The reliability and electrical instability of ReRAMs were remarkably improved by blending the $HfO_x$ into PMMA. An Ohmic conduction path was commonly generated in the LRS (low resistance state). In HRS (high resistance state), the PMMA-based ReRAM showed SCLC (space charge limited conduction). the PMMA-$HfO_x$ hybrid ReRAM and $HfO_x$-based ReRAM revealed the Pool-Frenkel conduction. As a result of flexibility test, serious defects were generated in $HfO_x$ film deposited on PI (polyimide) substrate. On the other hand, the PMMA and PMMA-$HfO_x$ films showed an excellent flexibility without defect generation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.347-350
• /
• 2000

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for Li polymer battery. The temperature dependence of conductivity, impedance spectroscopy and electrochemical properties of PMMA/PVDF electrolytes as a function of a mixed ratio were reported for PMMA/PVDF based polymer electrolyte films, which were prepared by thermal gellification method of preweighed PMMA/PVDF, plasticizer and Li salt. The ion conductivity of PMMA/PVDF electrolytes was 10$\^$-3/S/cm, which may be applicable to a constituent of lithium secondary battery. 5PMMA20PVDFLiC1O$_4$PC$\sub$8/EC$\sub$8/ electrolyte remains stable up to 5V vs. Li/Li$\^$+/. Steady state current method and AC impedance were used for the determination of transference numbers in PMMA/PVDF electrolyte film. The transference number of 5PMMA20PVDFLiC1O$_4$PC$\sub$8/EC$\sub$8/ electrolyte is 0.55.

• Tribology and Lubricants
• /
• v.21 no.4
• /
• pp.177-184
• /
• 2005

The molecular dynamics simulation of nanoimprint lithography (NIL) using $SiO_2$ stamp and amorphous poly-(methylmethacrylate) (PNMA) film is performed to study pattern transfer in NIL. Force fields including bond, angle, torsion, van der Waals and electrostatic potential are used to describe the intermolecular and intramolecular force of PMMA molecules and $SiO_2$ stamp. Nose-Hoover thermostat is used to control the system temperature and cell multipole method is adopted to treat long range interactions. The deformation of PMMA film is observed during pattern transfer in the NIL process. For the detail analysis of deformation characteristics, the distributions of density and stress in PMHA film are calculated. The adhesion and friction forces are obtained by dividing the PMMA film into subregions and calculating the interacting force between subregion and stamp. Their effects on the pattern transfer are also discussed as varying the indentation depth and speed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1390-1393
• /
• 2006

The transmittance of bare glass was enhanced up to about 20% by coating it with a PMMA (Poly Methyl Meta Acrylate) film mixed with silica gel. This lowrefractive- index film greatly reduces total reflection inevitable for bare glass, and thus will be useful for increasing the coupling-out efficiency of OLED.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.29-32
• /
• 2003

Multi -walled carbon nanotube(MWNT)/poly(methyl methacrylate) composites were fabricate d through film casting. Manufacturing process was established using a ultrasonic cleaner and a homogenizer. Acetone was used as a solvent to melt PMMA and mix with MWNT. The ultrasonic cleaner performed an important role in producing MWNT/MMA nanocomposites. Ultrasonic energy was utilized to disperse MWNT in acetone. Also, melting PMMA in acetone and mixing MWNT and PMMA were achieved using the homogenizer. It was confirmed that the nanohlbes were well dispersed in PMMA according to SEM images.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1509-1514
• /
• 2008

To fabricate microsized poly(methyl methacrylate)(PMMA) beads of uniform size and density on poly(ethylene terephthalate) (PET) fis, we introduce an electro spraying technique that uses a target electrode applied with an ac electric fid. Using the apparatus and various material properties, we could obtain uniform size PMMA beads which were deposited on the thin PET film. The optical properties, transmittance and light diffusivity of the fis electro sprayed with the PMMA were characterized. The results show that the sprayed beads appear to act as a good optical diffuser, like microlenses. To understand the effect of process variables, applied field conditions and rheological properties, the morphological pictures of the deposited particles were investigated through the optical and scanning electron microscope.

• Journal of the Korean Vacuum Society
• /
• v.18 no.5
• /
• pp.372-376
• /
• 2009

In the modern semiconductor industry, lithography process is used to construct specific patterns. However, due to the decreasing of line width, these days, more and more researchers are interested in PMMA(Poly Methyl Methacrylate) lithography by using e-beam instead of the prior method, PR(Photoresist) lithography by using UV(Ultra-Violet). Additionally, the patterns constructed by lithography are collapsed during the process of cleansing remnants and the resistance against the breakdown of the patterns is known to be proportional to the elastic modulus of pattern-constructing materials. In this research, we measured the change of hardness and elastic modulus of PMMA film surface according to the change of time spent to soft-bake the PMMA film. During the measurement, we controlled the tip pressure from $25{\mu}N$ to $8,500{\mu}N$ having intervals that are $134.52{\mu}N$. For these measurements, we used the Triboindenter from Hysitron to gauge the hardness and elastic modulus and the tip we used was Berkovich diamond Tip.