• 상하수도학회지
• /
• 제25권5호
• /
• pp.767-775
• /
• 2011

In this study we verified if the electro-coagulation process can treat properly the nitrate and fluoride that are not removed well in the conventional small water treatment plants which usually employ chlorination and filtration only. As we gave a change of electrode material and gap-distance between electrodes, removal efficiency of the nitrate and fluoride was determined by electro-coagulation process which were equipped with aluminum and stainless steel (SUS304) electrodes. In addition, electrode durability was investigated by determination of electrodes mass change during the repetitive experiments. Removal efficiency was great when aluminum was used as an anode material. Nitrate removals increased as electric density and number of electrodes increased, but fluoride removal was less sensitive to both parameters than nitrate. After 10 minutes of contact time with the current density from $1{\times}10^{-3}$ to $3{\times}10^{-3}A/cm^{2}$, nitrate and fluoride concentration ranged from 9.2 to 1.2mg/L and from 0.02 to 0.01mg/L, which satisfied the regulation limits. Regardless of the repeating number of experiments, removal efficiency of both ions were almost similar and the change of electrode mass ranged within ${\pm}$0.5%, indicating that the loss of the electrode mass is not so much great under the limited circumstances.

• 한국식품저장유통학회지
• /
• 제3권2호
• /
• pp.121-129
• /
• 1996

Plum highlighted as a health food is needed to diversify the processed products because labor storage is big problem since the fruit was producted massively in June. The Plum was extracted by the pressing type extractor after washing, drying and removing the seed by seed separator. The crude extract was concentrated with stainless steel vessel at different temperature and stirring speed. This study was obtained as follows. The sugar content of fresh plum concentrated extract was 55.3~58.3$^{\circ}$Brix, and of the freezing plum concentrated extract was 75.5~70.3$^{\circ}$Brix. In color difference, the freezing plum concentrated extract was more deep black than fresh plum. In change patten of pH, it was decreased as concentration was proceed. The final pH was 2.3~2.2 in fresh plum, and 1.8~2.2 in freezing plum. The total acid content of fresh plum concentrated extract and the freezing plum was 45.4~47.8, 60.3~60.9%, respectively. The content of evaporation at 85$\pm$5$^{\circ}C$ was constant irrespective of stirring speed. The yield of extraction of fresh plum was higher than freezing plum. According to this results, the use of stainless vessel, 50rpm, which gave a highly qualified plum concentrated extract.

• Steel and Composite Structures
• /
• 제12권1호
• /
• pp.53-72
• /
• 2012

In this study, the physically-based failure models for matrix and fibers in compression and tension loading are introduced. For the 3D stress based fiber kinking model a modification is proposed for calculation of the fiber misalignment angle. All of these models are implemented into the finite element code by using the advantage of damage variable and the numerical results are discussed. To investigate the matrix failure model, purely in-plane transverse compression experiments are carried out on the specimens made by Glass/Epoxy to obtain the fracture surface angle and then a comparison is made with the calculated numerical results. Furthermore, shear failure of $({\pm}45)_s$ model is investigated and the obtained numerical results are discussed and compared with available experimental results. Some experiments are also carried out on the woven laminated composites to investigate the fracture pattern in the matrix failure mode and shown that the presented matrix failure model can be used for the woven composites. Finally, the obtained numerical results for stress based fiber kinking model and improved ones (strain based model) are discussed and compared with each other and with the available results. The results show that these models can predict the kink band angle approximately.

• 한국태양에너지학회 논문집
• /
• 제21권1호
• /
• pp.61-69
• /
• 2001

The heat transfer characteristics of horizontal and vertical mantle heat storage tanks are studied in order to replace the tank-coil heat exchanger for application in thermosyphon solar water heaters. In this study, 5 mantle storage tanks with different geometric shape are manufactured into stainless steel and each tank is tested. For the test, The inlet flow rate of the heat transfer fluid is maintained 1.2 lpm consistently. The heat transfer fluid temperature through the mantle is $70{\pm}1^{\circ}C$. The temperatures of 26 points included the ambient temperature are measured at every one minute. The measured data are used to calculate the overall heat transfer coefficient(UA) using the LMTD(Log Mean Temperature Difference) method and it is used on the analysis of the heat transfer characteristics to search for optimum arrangement.

• International Journal of Advanced Culture Technology
• /
• 제8권2호
• /
• pp.246-251
• /
• 2020

Dimethyl Ether(DME) engine use a highly efficient alternative fuel having a great quantity of oxygen and has a advantage no polluting PM gas. The existing DME fuel cam material is a highly expensive carbide alloy, and it is difficult to take a price advantage. Therefore the study of replacing body area with inexpensive steel material excluding piston shoe and contact area which demands high characteristics is needed. The development of WC-Ni base carbide alloy optimal bonding composition technique was accomplished in this study. To check out the influence of bonding temperature and time, bonding characteristics of sintering temperature was experimented. The hardness of specimen and bonding rate were measured using ultrasound equipment. The bonding state of each condition was excellent, and the thickness of mid-layer, temperature and maintaining time were measured. The mid-layer thickness according to bonding temperature and maintaining time were observed with optical microscope. We analyzed the micro-structural analysis, formation of bonding specimen, wafer fabrication and fuel cam abrasion test. Throughout this study, we confirmed that the fuel cam for DME engine which demands high durability against velocity and pressure is excellent.

• Steel and Composite Structures
• /
• 제32권5호
• /
• pp.633-642
• /
• 2019

In this work, lightweight sandwich plates consisting of a functionally graded porous (FGP) core and two laminated composite face sheets resting on elastic foundation have been proposed. Three different profiles are considered for the distributions of porosities along core thickness. The main aim of this paper is the investigation of the buckling behavior of the proposed porous sandwich plates (PSPs) by reporting their critical mechanical loads and their corresponding mode shapes. A finite element method (FEM) based on first order shear deformation theories (FSDT) is developed to discretize governing equations for the buckling behavior of the proposed sandwich plates. The effects of porosity dispersion and volume, the numbers and angles of laminated layers, sandwich plate geometrical dimensions, elastic foundation coefficients, loading and boundary conditions are studied. The results show that the use of FGP core can offer a PSP with half weight core and only 5% reduction in critical buckling loads. Moreover, stacking sequences with only ${\pm}45$ orientation fibers offer the highest values of buckling loads.

• Asian-Australasian Journal of Animal Sciences
• /
• 제20권10호
• /
• pp.1580-1586
• /
• 2007

The objective of this study was to compare the bioefficacy of L-lysine sulfate relative to L-lysine${\cdot}$HCl for 10 to 20 kg pigs. Two experiments were conducted to determine the bioefficacy of the two sources of lysine using daily gain, feed conversion, plasma urea nitrogen and nitrogen retention as the response criteria. In experiment 1, 168 crossbred barrows ($Landrace{\times}Large$ White), weaned at $28{\pm}3$ d ($9.07{\pm}0.78$kg body weight), were allotted to one of seven dietary treatments in a $2{\times}3$ (two lysine $sources{\times}three $ lysine levels) factorial arrangement of treatments with an added negative control treatment group. The basal diet was based on corn, peanut meal and soybean meal and provided 0.67% lysine. The basal diet was supplemented with 0.1, 0.2 or 0.3% lysine equivalents supplied from either L-lysine sulfate or L-lysine${\cdot}$HCl. Each treatment was fed to six pens of pigs with four pigs per pen. The trial lasted 21 days. The relative bioefficacy value of lysine in L-lysine sulfate using daily gain, feed conversion and plasma urea nitrogen as response criteria was 1.01, 1.05 and 1.04 of the lysine in L-lysine${\cdot}$HCl, respectively. In experiment 2, 42 crossbred ($Landrace{\times}Large$ White) pigs ($16.03{\pm}1.58$ kg body weight) were housed in stainless steel metabolism cages for 10 d and fed the seven diets used in the nitrogen-balance trial. The relative bioefficacy value of L-lysine sulfate was estimated to be 0.95 as effective as L-lysine${\cdot}$HCl for nitrogen retention on an equimolar basis. The t-test analysis revealed that bioefficacy of lysine in L-lysine sulfate was not significantly different from lysine in L-lysine${\cdot}$HCl, which was set at 1.00. In conclusion, L-lysine sulfate can be used instead of L-lysine${\cdot}$HCl to fortify lysine-deficient diets fed to 10 to 20 kg pigs.

• Asian-Australasian Journal of Animal Sciences
• /
• 제17권4호
• /
• pp.504-510
• /
• 2004

Two experiments were conducted. In expt. 1, a total of fifty-four pigs (L$\times$Y$\times$D, 56.14$\pm$1.7 kg) were used for a feeding trial to determine the effect of wet feeding of a commercial-type diet without food waste (FW). Treatments were dry (Control), wet (WF) and wet+dry feeding (WDF). For wet feeding, the diet was mixed with water at a ratio of 1:2.5 (feed:water). A wet feed was given during the whole experimental period for the WF group, but the dry feed was given during the finisher period for the WDF group. In expt. 2, a total of fifty-four pigs(L$\times$Y$\times$D, 55.7$\pm$1.8 kg) were used for a feeding trial to determine the effect of wet feeding of FW. Treatments were a commercial-type dry (Control), wet fermented food waste (WFFW) and WFFW+dry feeding (WFFW+DF). For wet feeding of fermented food waste, however, some ingredients (concentrate) were added to make nutrient contents comparable to the control diet. The FW collected was ground ($\leq$5 mm), heated with a steam jacket (140$\pm$3$^{\circ}C$) and fermented with probiotics for one day in a steel container at 30-40$^{\circ}C$. For the WFFW group, the wet feed was given during the whole experimental period, but a dry feed was given during finisher period for the WFFW+DF group. In expt. 1, during the grower period, pigs fed wet feed showed higher average daily gain (ADG) and feed conversion ratio (FCR) than those fed only dry feed (p<0.05). During the finisher period, pigs in the WDF group showed better ADG and FCR than the control group. During the entire experimental period, pigs in the WDF group grew faster (p<0.05) than those in the control group, and the same trend was found in FCR. Also, dressing percentage, backfat thickness, lean %, and pork color were not affected by the wet feeding of diets in this study. In expt. 2, during the grower period, pigs fed diets containing FW showed lower (p<0.05) ADG than those fed the control diet. But FCR was better (p<0.05) in pigs fed FW than in the control group. During the finisher period, pigs in the WFFW+DF group grew faster (p<0.05) than those in the control and WFFW groups. During the entire experimental period, pigs fed the control diet showed better ADG (p<0.05) than those fed FW, but feed intake and FCR were vice versa. Dressing percentage was lower (p<0.05) in the WFFW than in the control group, but backfat was thinner in the WFFW group than in the control group. In summary, it can be concluded that wet feeding of formula feed can improve daily gain, however, feeding fermented wet food waste may reduce daily gain of finishing pigs, even though it was fermented and the nutrient was fortified with concentrates. In addition, dry feeding of a formula feed during the finishing period can improve daily gain in pigs fed a wet feed with or without food waste during the grower period.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.97-97
• /
• 2009

The use of thin plate increases due to the need for light weight in large ship. Thin plate is easily distorted and has residual stress by welding heat. Therefore, the thin plate should be carefully joined to minimize the welding deformation which costs time and money for repair. For one effort to reduce welding deformation, it is very useful to predict welding deformation before welding execution. There are two methods to analyze welding deformation. One is simple linear analysis. The other is nonlinear analysis. The simple linear analysis is elastic analysis using the equivalent load method or inherent strain method from welding experiments. The nonlinear analysis is thermo-elastic analysis which gives consideration to the nonlinearity of material dependent on temperature and time, welding current, voltage, speed, sequence and constraint. In this study, the welding deformation is analyzed by using thermo-elastic method for PCTC(Pure Car and Truck Carrier) which carries cars and trucks. PCTC uses thin plates of 6mm thickness which is susceptible to welding heat. The analysis dimension is 19,200mm(length) * 13,825mm(width) * 376mm(height). MARC and MENTAT are used as pre and post processor and solver. The boundary conditions are based on the real situation in shipyard. The simulations contain convection and gravity. The material of the thin block is mild steel with $235N/mm^2$ yield strength. Its nonlinearity of conductivity, specific heat, Young's modulus and yield strength is applied in simulations. Welding is done in two pass. First pass lasts 2,100 second, then it rests for 900 second, then second pass lasts 2,100 second and then it rests for 20,000 second. The displacement at 0 sec is caused by its own weight. It is maximum 19mm at the free side. The welding line expands, shrinks during welding and finally experiences shrinkage. It results in angular distortion of thin block. Final maximum displacement, 17mm occurs around welding line. The maximum residual stress happens at the welding line, where the stress is above the yield strength. Also, the maximum equivalent plastic strain occurs at the welding line. The plastic strain of first pass is more than that of second pass. The flatness of plate in longitudinal direction is calculated in parallel with the direction of girder and compared with deformation standard of ${\pm}15mm$. Calculated value is within the standard range. The flatness of plate in transverse direction is calculated in perpendicular to the direction of girder and compared with deformation standard of ${\pm}6mm$. It satisfies the standard. Buckle of plate is calculated between each longitudinal and compared with the deformation standard. All buckle value is within the standard range of ${\pm}6mm$.

• The Korean Journal of Physiology and Pharmacology
• /
• 제3권5호
• /
• pp.481-490
• /
• 1999

To investigate the changes in the responses of vestibular neurons with time during vestibular compensation, the resting activity and dynamic responses of type I and II neurons in the medial vestibular nuclei to sinusoidal angular acceleration were recorded following unilateral labyrinthectomy (ULX) in Sprague-Dawley rats. The unitary extracellular neuronal activity was recorded from the bilateral medial vestibular nuclei with stainless steel microelectrodes of $3{\sim}5\;M{\Omega}$ before ULX, and 6, 24, 48, 72 hours, and 1 week after ULX under pentobarbital sodium anesthesia (30 mg/kg, i.p.). Gain (spikes/s/deg/s) and phase (in degrees) were determined from the neuronal activity induced by sinusoidal head rotation with 0.05, 0.1, 0.2, and 0.4 Hz. The mean resting activity before ULX was $16.7{\pm}8.6$ spikes/s in type I neurons $(n=67,\;M{\pm}SD)$ and $14.5{\pm}8.4$ spikes/s in type II neurons (n=43). The activities of ipsilateral type I and contralateral type II neurons to the lesion side decreased markedly till 24 hr post-op, and a significant difference between ipsilateral and contralateral type I neurons sustained till 24 hr post-op. The gain at 4 different frequencies of sinusoidal rotation was depressed in all neurons till 6 or 24 hr post-op and then increased with time. The rate of decrease in gain was more prominent in ipsilateral type I and contralateral type II neurons immediately after ULX. Although the gain of those neurons increased gradually after 24 hours, it remained below normal levels. The phase was significantly advanced in all neurons following ULX. These results suggest that a depression of activities in ipsilateral type I and contralateral type II neurons is closely related with the occurrence of vestibular symptoms and restoration of activities in those neurons ameliorates the vestibular symptoms.