• Geomechanics and Engineering
• /
• 제18권1호
• /
• pp.29-39
• /
• 2019

In this paper, it was presented an investigation on the load-settlement and vertical stress analysis of the ring footings on the loose sand bed by conducting both laboratory model tests and numerical analyses. A total of twenty tests were conducted in geotechnical laboratory and numerical analyses of the test models were carried out using the finite element package Plaxis 3D to find the ultimate capacities of the ring footings. Moreover, the results obtained from both foregoing methods were compared with theoretical results given in the literature. The effects of the ring width on bearing capacity of the footings and vertical stresses along the depth were investigated. Consequently, the experimental observations are in a very good agreement with the numerical and theoretical results. The variation in the bearing capacity is little when $r_i/R_o$ <0.3. That means, when the ring width ratio, $r_i/R_o$, is equal to 0.3, this option can provide more economic solutions in the applications of the ring footings. Since, this corresponds to less concrete consumption in the ring footing design.

• 대한토목학회논문집
• /
• 제41권5호
• /
• pp.533-541
• /
• 2021

옹벽 구조물은 철도, 도로, 원자력 발전소, 댐, 하천 시설 등 토압 저항을 통한 사면 붕괴방지에 활용된다. 동토압 산정 및 지진시 거동에 대한 특성을 파악하기 위해 많은 연구자들은 다양한 수치해석 프로그램(FLAC, PLAXIS, ABAQUS 등)을 활용하여 동적 하중에 대한 구조물과 지반의 비선형 거동을 분석하고 있다. 또한, 구조물의 지진에 대한 안전성을 확보하기 위해 지진취약도 곡선을 산정하여 확률론적 지진안전성 평가를 수행하고 있다. 본 연구에서는 수치해석프로그램 FLAC2D를 활용하여 뒷채움토의 사면 경사도가 있는 역T형 옹벽의 지진거동 특성을 파악하고, 옹벽 벽체의 상대적인 수평변위를 고려하여 지진취약도 평가를 수행하였다. 다양한 지진하중을 고려하기 위해 암반에서 계측된 7개의 지진파를 활용하여 각 지반특성 별(S2, S4) 비선형 지반응답해석을 수행하였고, 산정된 지진파의 크기를 5가지(0.1, 0.3, 0.5, 0.7, 0.9 g의 최대지반가속도)로 조정하였다. 본 연구에 활용된 수치해석 모델은 다른 수치해석결과와 실험결과, 주동토압 산정식을 활용하여 비교 검증하였다. 옹벽 높이에 대한 상대수평변위를 손상지수로 고려하여 옹벽의 손상상태를 결정하여 지진취약도 곡선을 산정하였다. 상대적으로 깊고 토층 평균 전단파 속도가 느린 S4 지반에서 S2 지반보다 옹벽 벽체의 수평 변위에 대한 지진취약도가 크게 산정되었음을 확인하였다.

• Geomechanics and Engineering
• /
• 제28권3호
• /
• pp.239-253
• /
• 2022

Suitable techniques to stabilize organic soil and improve its engineering behaviour are in demand. Despite various alternatives, nano-additives proved to be an effective stabilizer owing to their strength enhancing properties. The study focuses on using nano-silica as a potential stabilizer to improve organic silt. Soil was treated with four dosages of nano-silica namely 0.2%, 0.4%, 0.6% and 0.8% of dry weight of the soil. Nano-silica treated soil showed a strength increase of nearly 25% at a dosage of 0.4% after curing for two hours. Strength of the treated soil improved with age. Strength improved by nearly 62.9% after 28 days of curing and 221.4% after 180 days of curing due to formation of Calcium - Silicate - Hydrate (CSH) gel in the soil matrix. Dosage of 0.6% nano-silica is observed to be the optimum dosage. Coefficient of permeability and compression index showed an increase by 13.32 and 5.5 times respectively owing to aggregation of particles and creation of void spaces as visualized from the scanning electron micrographs. Further model foundation study and numerical parametric studies using PLAXIS 2D indicate that optimized and economic results can be obtained by varying the additive dosage with depth.

• Geomechanics and Engineering
• /
• 제36권3호
• /
• pp.277-293
• /
• 2024

Shored Mechanically Stabilized Earth (SMSE) walls are types of soil retaining structures that increase soil stability under static and dynamic loads. The damage caused by an earthquake can be determined by evaluating the probabilistic seismic response of SMSE walls. This study aimed to assess the seismic performance of SMSE walls and provide fragility curves for evaluating failure levels. The generated fragility curves can help to improve the seismic performance of these walls through assessing and controlling variables like backfill surface settlement, lateral deformation of facing, and permanent relocation of the wall. A parametric study was performed based on a non-linear elastoplastic constitutive model known as the hardening soil model with small-strain stiffness, HSsmall. The analyses were conducted using PLAXIS 2D, a Finite Element Method (FEM) program, under plane-strain conditions to study the effect of the number of geogrid layers and the axial stiffness of geogrids on the performance of SMSE walls. In this study, three areas of damage (minor, moderate, and severe) were observed and, in all cases, the wall has not completely entered the stage of destruction. For the base model (Model A), at the highest ground acceleration coefficient (1 g), in the moderate damage state, the fragility probability was 76%. These values were 62%, and 54%, respectively, by increasing the number of geogrids (Model B) and increasing the geogrid stiffness (Model C). Meanwhile, the fragility values were 99%, 98%, and 97%, respectively in the case of minor damage. Notably, the probability of complete destruction was zero percent in all models.

• Geomechanics and Engineering
• /
• 제9권4호
• /
• pp.415-426
• /
• 2015

Researches have been done to discover ways to strengthen peat soil deposits. In this model study, fibrous peat that is the most compressible types of peat has been reinforced with precast peat columns stabilized with ordinary Portland cement and polypropylene fibres. Rowe cell consolidation tests as well as plate load tests (PLTs) were conducted on various types of test samples to evaluate the strength and deformation of untreated peat and peat reinforced by various types of columns. PLTs were conducted in a specially designed and fabricated circular steel test tank. The compression index ($C_c$) and recompression index ($C_r$) of fibrous peat samples reduced considerably upon use of precast columns. Also, PLT results confirmed the results obtained from Rowe cell tests. Use of polypropylene fibres added to cement further decreased ($C_c$) and ($C_r$) and increased load bearing capacity of untreated peat. Finite element method (FEM) using Plaxis 3D was carried out to evaluate the stress distributions along various types of tested samples and also, to compare the deformations obtained from FEM analysis with the actual maximum deformations found from PLTs. FEM results indicate that most of the induced stresses are taken on the upper portion of tested samples and reach their maximum values below the loading plate. Also, a close agreement was found between actual deformation values obtained from PLTs and values resulted from FEM analysis for various types of tested samples.

• Geomechanics and Engineering
• /
• 제12권2호
• /
• pp.223-238
• /
• 2017

In this study, bearing capacities and settlement profiles of six irregularly shaped footings located on sand have been experimentally and analytically investigated under the effect of axial loading. The main variable considered in the study was the geometry of the footings. The axial loads were applied from the center of gravities of the test specimens. Consequently, the effect of footing shape on the variation of the bearing capacities and settlement profiles have been investigated in this paper. The three dimensional finite element analyses of the test specimens were conducted using the PLAXIS 3D software. The finite element model results are in acceptable agreement with the results obtained using experimental investigation. In addition, the usability of the finite element technique by design engineers to determine the bearing capacities and settlement profiles of irregularly shaped footings was investigated. From the results of the study, it was observed that the geometric properties of the footings significantly influenced the variation of the bearing capacities and settlement profiles.

• Geomechanics and Engineering
• /
• 제34권6호
• /
• pp.611-621
• /
• 2023

This paper presents the results of a numerical investigation of the effect of geotextile reinforcement on underlying buried pipe behavior using PLAXIS 3D. In this study, variable parameters such as the in-plane stiffness of the geotextile, the pipe stiffness, the soil stiffness, the footing width, the geotextile width, and the location of the geotextile reinforcement layer are investigated. Deflections and bending moments acting on the pipe are evaluated for different combinations of variables and are presented graphically. It is observed that with an increase in the in-plane stiffness of the geotextile reinforcement, there is a tendency for a decrease in both deflections in the pipe and bending moments acting on the pipe. Conversely, with an increase in the pipe stiffness, geotextile reinforcement efficiency decreases. In the investigated region of soil stiffness, for the given pipe and geotextile stiffness, an optimum efficiency of geotextile is observed in medium dense soils. Further, it is shown that relative lengths of geotextile and footing has an important role on geotextile efficiency. Lastly, it is also demonstrated that relative location of geotextile layer with respect to the buried pipe plays an important role on the geotextile efficiency in reducing the bending moments acting on the pipe and deflections in the pipe. In general, geotextiles are more efficient in reducing the bending moments as opposed to reducing deflections of the pipe. Numerical validation is done with an experimental study from the literature to observe the applicability of the numerical model used.

• 한국철도학회논문집
• /
• 제16권5호
• /
• pp.386-393
• /
• 2013

본 연구에서는 궤도 하부 노반상에서 다짐도 확인 및 강화노반 두께 결정을 위하여 사용되는 변형계수 $E_{v2}$ 측정방법의 적절성과 측정값의 유효성을 검토하였다. 이를 위하여 반복평판재하시험(RPBT)을 실시하고 평판직하부에서 발생하는 압축변형률을 파악하였다. 동일 흙노반재료에 대한 공진주시험으로부터 획득된 전단탄성계수감소곡선과 $E_{v2}$를 비교하였다. 실 현장 RPBT의 발생변형률 수준과 변형계수의 크기가 합리적인지를 분석하기 위하여 응력조건과 대표 평균변형률계수($I_z$) 보정에 의해 반복평판재하시험 변형계수($E_{v2}$)를 재평가하였다. PLAXIS 프로그램을 이용하여 깊이에 따른 변형률 영향계수($I_z$)를 재산정하여 반복평판재하시험 결과($E_{v2}$) 해석에 미치는 변형률 영향계수의 영향을 분석하였으며 ABAQUS를 이용하여 3D궤도구조에서 노반이 받는 변형률수준을 확인하였다. 궤도하부구조가 경험하는 변형률수준에서의 변형계수 $E_{v2}$를 획득하기 위해서는 노반의 비선형성을 구현할 수 있도록 현 반복평판재하시험의 하중단계를 세분화할 필요성을 확인하였다.

• Geomechanics and Engineering
• /
• 제20권1호
• /
• pp.75-86
• /
• 2020

This study aims to simulate the stabilization process of fibrous peat samples using end-bearing Cement Deep Mixing (CDM) columns by three area improvement ratios of 13.1% (TS-2), 19.6% (TS-3) and 26.2% (TS-3). It also focuses on the determination of approximate stress distribution between CDM columns and untreated fibrous peat soil. First, fibrous peat samples were mechanically stabilized using CDM columns of different area improvement ratio. Further, the ultimate bearing capacity of a rectangular foundation rested on the stabilized peat was calculated in stress-controlled condition. Then, this process was simulated via a FEM-based model using Plaxis 3-D foundation and the numerical modelling results were compared with experimental findings. In the numerical modelling stage, the behaviour of fibrous peat was simulated based on hardening soil (HS) model and Mohr-Coulomb (MC) model, while embedded pile element was utilized for CDM columns. The results indicated that in case of untreated peat HS model could predict the behaviour of fibrous peat better than MC model. The comparison between experimental and numerical investigations showed that the stress distribution between soil (S) and CDM columns (C) were 81%C-19%S (TS-2), 83%C-17%S (TS-3) and 89%C-11%S (TS-4), respectively. This implies that when the area improvement ratio is increased, the share of the CDM columns from final load was increased. Finally, the calculated bearing capacity factors were compared with results on the account of empirical design methods.

• 한국터널지하공간학회 논문집
• /
• 제16권3호
• /
• pp.299-310
• /
• 2014

국가적으로 국토의 효율적 활용과 친환경성 등으로 인해 터널과 같은 지하공간 건설이 필요하다. 친환경적 요소의 중요성을 감안할 때, 산악지에 형성되는 도로건설에 대해 2-아치 및 대단면 터널로 계획되나 경제성, 시공성, 공사기간, 유지관리 등의 문제점을 가지고 있다. 따라서 본 연구에서는 2차로의 국도터널을 기준으로 현장조건과 지반조건을 고려하여 터널별 이격거리와 토피고를 변화시켜 경험식과 수치해석적으로 필라부의 안전성을 평가하였으며, 해석 프로그램으로 유한요소법을 적용한 Plaxis 2D를 활용하여 터널의 최소 필라폭 선정과 전체적인 터널의 거동특성을 분석하였다. 분석결과, Tie-Bolt에 의한 필라보강은 연직하중을 분산시켜 안전적인 근접병렬터널 계획이 가능하며, 터널 필라의 거동은 현장계측 결과와 잘 일치하는 것으로 나타났으며, 지반조건에 따라 터널 필라폭을 축소시킨다면 이전의 터널에 비해 효율적인 터널 활용이 가능하다.