• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.76-80
• /
• 1991

This paper presents a merit of feedforward Dyamic Matrix Control(DMC) for electrolyzer process. The electrolyzer consists of anode part and cathode part that are separated by ion membrane. As the electolyzer process consumes a large amount of electricity, electric power change is inevitable in order to take advantage of the cheaper electricity during night. But the electric power change makes the electrolyzer control difficult because the electric power change affect the dynamics of the process. Feedforward DMC treats the electric power change as a load disturbance and gives the weighting value to the disturbance prediction part in the DMC algorithm. Feedforward DC shows better regulation performance than PID control and feedforward-feedback control for electrolyzer process.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.523-527
• /
• 1991

A rubber pneumatic controlled actuator is a new actuator. It is very light With a high power-to-weight ratio. In this thesis, a control method for a two link robot arm using the rubber actuator is developed. The structure of the servo control is made up of two sections. The position control is performed by PID feedback control. The air pressure is controlled by Servo Valve Unit driven by PWM and the control input is compensated by software operation. The numerical simulation of this control method to two link robot arm is presented to verify the performance of the closed loop system. The actual control of the real two link robot arm with rubber actuator is taken and its results are discussed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.6
• /
• pp.608-611
• /
• 2012

This paper focuses on attitude stabilization performance improvement of the quadrotor flying robot. First, the dynamic model of quadrotor flying robot was estimated through PEM (Prediction Error Method) using experimental input/output data. And attitude stabilization performance was improved by increasing the generation frequency of PWM signal from 50 Hz to 500 Hz. Also, the controller is implemented using a standard PID (Proportional-Integral-Derivative) controller augmented with feedback on angular acceleration, allowed the gains to be significantly increased, yielding higher bandwidth. Improved attitude stabilization performance is verified by experiment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.136-139
• /
• 2000

Controller refinement scheme to improve the performance of a conventional system automatically in frequency domain is proposed. The controller automatic tuning method features using experimental frequency responses of the conventional closed-loop system, the conventional controller, and the improved closed-Imp system; instead of poorly modeled plant due to non-linearities and disturbances. The improved closed-loop system characteristics is automatically acquired by the conventional closed-loop system characteristics and the proposed performance index in system bandwidth. And the proper controller is realized by least squares approximation in frequency domain. To testify the usefulness of the approach, experimental results of robot path-tracking control applied with various controllers is used, and then is analyzed with respect to a equivalent proportional controller. Experimental results and analytic results are well-matched.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.303-306
• /
• 1997

Magnetic bearings have been adopted to support the rotor by electromagnetic force without mechanical contact and have many advantages. The application of the magnetic bearings have become more and more widespread in recent years. But magnetic bearings require feedback control for stable operation because they are inherently open loop unstable systems. In this study, H infinity controller has been applied for rotor-magnetic bearing system for vibration control. The result showed that H infinity controller has better performance than PID controller through simulations.

• Journal of the Korean Society for Precision Engineering
• /
• v.9 no.3
• /
• pp.29-41
• /
• 1992

According to the recent increase of demands for multi-function and economics on hydraulic excavator, it is required that excavator should have simple operation, higher and operational efficiency, however the modeling of engine/pump system of excavator is not prescribed by the paper. So, in this paper the modeling of engine/pump system of excavator is suggested by identification method from step response and verified effectiveness of identification system by comparing with experimental results which was conducted using PID controller. To improve the problem of parameter variation and modeling error in the system, sliding mode control was introduced and new switching surface was designed. This control algorithm was applied to a hydraulic excavator by simulation, and its effectiveness was verified, and the results of variable structure system for the excavator system using a output component was compared with that of full state feedback when load disturbances and system paramenter variation exist.

• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.2
• /
• pp.23-32
• /
• 1988

A control system for improving the moving accuracy of robotic manipulators with elastic joints is devloped. The dynamics of manipulator system is splitted into two sub-dynamics; of arm-link and actuator rotor- link, which are coupled statically through joint torque. Two contorl loops are implemented respectively around both sub-dynamic systems. Computed torque algorithm with acceleration feedback is used for the arm-link control loop, and for the actuator rotor-link control loop PID algorithm is adopted. The resulting control system is tested through a series of computer simulation for a PUMA type manipulator, The reaults show good performance of the developed control system for wide range of joint stiffness and moving speed.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.249-250
• /
• 2006

In this paper, hardware design and implementation of digital controller for the High Precision Digital Power Supply (HPDPS) based on Digital Signal Processor (DSP) and Field Programmable Gate Array (FPGA) is presented. Developed digital controller is composed of high resolution Digital Pulse Width Modulation (DPWM) and high resolution analog to digital converter circuit with anti-aliasing filter. And Digital Signal Processor (DSP) has the capability of a few micro-second calculation time for one feedback loop. 32-bit DSP and DPWM with 150[ps] step resolution is used to implement the HPDPS. Also 18-bit 2 mega sample per second ADC board is adopted for the developed digital controller. Also, hardware structure of the developed digital controller and experimental results of the first prototype board for HPDPS is described.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.150-155
• /
• 1997

In this paper,we present neural network for control of Left Ventricular Assist Device(LVAD)system with a pneumatically driven mock cirulation system. It is necessary to apply high perfomance control techniques, since the LVAD system represent nonlinear and time-varing characteristics. Fortunately, the neural network can be applied to control of a nonliner dynamic system by learning capability. In this study,we identify the LVAD system with neural network and control the LVAD system by PID controller and neural network feedforward controller. The ability and effectiveness of controlling the LVAD system using the proposed algorithm will be demonstrated by computer simulation and experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.1332-1336
• /
• 1990

This paper deals with some analytical and experimental aspects to control a multi-magnet suspended vehicle. Because the response of a multi-magnet vehicle shows mutually coupled interaction, an analytical description of the vehicle dynamics is necessary. For numerical computations, a linearized modelling of vehicle dynamics is dicussed and computer simulation is carried out. And for the experiment, a test vehicle suspended by four magnets has been made and investigated by local control of each magnet. Two algorithms by PID and state feedback control law are used and compared with each other. Some kinds of disturbance characteristics and coupling effects of the width change of the test vehicle are experimented.