• Elastomers and Composites
• /
• v.36 no.1
• /
• pp.3-13
• /
• 2001

To resolve environmental problem of waste tire and asbestos and also to capitalize the wastes, we developed a new kind of friction material using scrap tire, potassium hexatitanate, filler, and friction modifier in which rubber made a continuous phase. The material containing 5, 20, 10, 20phr of potassium hexatitanate, phenol, friction modifier, $BaSO_4$, respectively showed good friction properties, high and stable coefficient or friction, and low wear rate.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.29-29
• /
• 2010

Engineering plastics have excellent electrical properties, mechanical strength and various characteristic which include chemical resistance, environmental resistance, weatherability at a wide temperature range. It has good characteristic(light weight, good productivity) as compare with epoxy or porcelain insulators. However, engineering plastics not suited to outdoor insulator because it isn't hydrophobic. Therefore, to over come these critical problems, we improve the surface insulation characteristics of engineering plastic by coating micro-, nano- size inorganic fillers added to RTV-SIR(Room temperature vulcanized-silicone rubber) at this plastic surface. The effect is analyzed through salt-fog test, tracking test. In conclusion, the engineering plastic coated RTV with micro-$Al_2O_3$20[phr], nano-Al(OH)3 1 ~ 3[phr] improved much better than the others.

• Elastomers and Composites
• /
• v.54 no.4
• /
• pp.335-344
• /
• 2019

In this work, styrene butadiene rubber (SBR) and styrene butadiene styrene (SBS) were used to modify asphalt, resulting in SBR- and SBS-modified asphalt, respectively. The two modified asphalts were emulsified with a nonionic emulsifier (Span 60) and cationic emulsifiers (ID, DDA) and their phase stabilization was investigated via particle size, Zeta potential, and flow behavior analysis. With increasing amount of the mixed emulsifier, the particle size decreased, leading to an increase in viscosity. The shear thinning behaviors and Zeta potential values ranging from 35-65 mV were determined and remained considerably stable. In addition, the adhesion strength and compression strength of the SBR-and SBS-modified asphalt emulsion were evaluated via surface free energy examination. The remarkable adhesion and compression strengths were estimated when 5 phr ID and 6 phr DDA were added to the emulsified asphalt modified with SBR and SBS. Therefore ID and DDA, the two cationic surfactants, played significant roles in improving the dispersion and interfacial adhesion strength, resulting in the improved adhesion and compression strength of the emulsified asphalts modified with SBR and SBS.

• Membrane Journal
• /
• v.15 no.1
• /
• pp.62-69
• /
• 2005

SEBS-clay hybrid membranes were prepared by melt intercalation method with internal mixer. In the hybrid, the amount of clay content was fixed to 5 phr. MMT was intercalated or exfoliated by the ionomer and it was confirmed by X-ray diffraction method. D-spacing of the characteristic peak from MMT plate in SAXD was moved and diminished. Gas permeability, mechanical properties and thermal properties of the SEBS-clay hybrid membranes were investigated. Gas permeability through the SEBS-clay hybrid membranes decreased due to increased tortuosity made by intercalation of clay in SEBS.

• Elastomers and Composites
• /
• v.41 no.1
• /
• pp.10-18
• /
• 2006

Influence of low molecular weight polybutadiene (liquid PB) treated with maleic anhydride on properties of a silica-filled SBR compounds was studied. Silica dispersion was improved by adding liquid PB. The liquid PB treated with maleic anhydride (liquid MAPB) was found to be more effective for the improvement of silica dispersion than the liquid PB without maleic anhydride (liquid NPB). Viscosity of the SBR compound decreased by adding the liquid PB. The crosslink density decreased with increase of the liquid PB content and the cure rate became slower with increasing the liquid PB content. Considering the experimental results, it was believed that addition of small amount of the liquid PB (less than 5 phr) was desirable to improve properties of silica-filled SBR compounds.

• Elastomers and Composites
• /
• v.38 no.1
• /
• pp.65-71
• /
• 2003

Influence of low molecular weight styrene-butadiene rubber (liquid SBR) on properties of a silica-filled styrene-butadiene rubber (SBR) compounds was studied. Viscosity of the silica-filled SBR compound decreased by adding the liquid SBR. The crosslink density decreased and the cure rate became slower as the liquid SBR content increased. The modulus and tensile strength decreased while the elongation at break became longer by increasing the liquid SBR content. The abrasion losses were nearly the same irrespective of the liquid SBR content. This might be due to the improvement of silica dispersion by adding the liquid SBR. Considering the experimental results, it was believed that addition of small amount of the liquid SBR (less than 5 phr) was desirable to improve properties of silica-filled SBR compounds.

• The Korean Journal of Zoology
• /
• v.15 no.2
• /
• pp.92-93
• /
• 1972

Ox-RBC로부터 Moddy法에 依하여 Ox-RCM抗原을 抽出하여 몇가지 分析을 實施하였다. Lyophilized 한 Ox-RCM protein의 化學的 分析 結果 total protein은 $55\\pm 1.3%$, total nitrogen은 9.2%, carbohydrate 8.5% 그리고 total acid soluble phosphorus는 $0.96\\pm 0.1%$였다. Polyacrylamide gel electrophoresis한 結果 Ox-RCM은 12 $\\sim$ 15個, Pre-VRS fraction은 8個 및 PHR 分劃은 9個의 pattern을 나타냈다. Amino acid의 分析 結果로 cystine이 4.93 $\\sim$ 3.72 moles/100 moles 이고 glycine이 最高로 26.7 $\\sim$ 13.5 moles/100 moles였고 最低로 methionine 이었으나 試料의 抽出方法에 따라 그 値의 變動을 볼 수 있다.

• Clean Technology
• /
• v.16 no.4
• /
• pp.245-253
• /
• 2010

Optimum conditions for UV-radiated photopolymerization of unsaturated polyester that could be used as protecting layer of large diameter pipe were investigated in this paper. UV photopolymerization method was selected to solve the problems, arising when thermal polymerization by organic peroxide was used, such as the instability of peroxide initiator, the evolution of volatile organic compound, and thermal deformation of product. Two of the photo-initiators (Irgacure 819 and Darocure 1173) well known for its penetrating ability deep into the polymer layer were selected, and the optimum conditions for photopolymerization (1.5 phr initiator content, 1:1.2 initiator ratio, Ga lamp for UV source) were found from the thermal and mechanical test results of the resultant UP polymers. In addition, composite materials containing UP polymer and glass fiber were tested for hardness, impact strength, and flexural strength to find that the impact strength of composite significantly improved.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.4
• /
• pp.376-384
• /
• 2014

This study investigated the effect of nanocellulose, such as microfibrillated cellulose (MFC) and cellulose nanocrystal (CNC), and aminated starch on tensile property and thermal stability of plasticized starch film. Glycerol (23 wt%) was used as a plasticizer and nanocelluloses of 1-30 parts per hundred parts of resin (phr) in the basis of plasticized starch were added. Tensile strength and elastic modulus increased with increasing nanocellulose addition amount, whereas elongation at break decreased. Tensile properties of MFC-reinforced starch film were higher than those of CNC-reinforced film. Optimum addition amount of aminated starch, which is commonly used for paper sizing, to improve tensile property of film, was found to be 5%. And 1% addition of aminated starch showed the best effect in the improvement of tensile property of the film. Thermal stability was improved with the addition of MFC to plasticized starch film with and without aminated starch.

• Polymer(Korea)
• /
• v.31 no.6
• /
• pp.474-478
• /
• 2007

Polymer substrate materials with low dielectric loss were obtained by fabricating the composite using dicyclopentadienyl bisphenol cyanate ester oligomer and polyphenylene ether (PPE). From the analysis of the curing reaction of oligomer and catalyst, it was observed that the optimum amount of catalyst was 0.02 phr of Zn content. It was applied to the fabrication of polymer composite. By changing oligomer/PPE weight ratio, the peel strength and the gel content of the fabricated composites were measured, and then, the dielectric constant and the dissipation factor were measured in the GHz frequency range. The amount of PPE affected the peel strength and the dielectric properties of composites. However, the amount of catalyst did not affect them at all. Resulting from all experiments, we obtained polymer composite laminates haying the peel strength of above 1 kN/m and the low dissipation factor of 0.004 at 1 GHz.