• Journal of Adhesion and Interface
• /
• v.5 no.1
• /
• pp.29-35
• /
• 2004

We have prepared polyster/nanQhybridized polyimide films in the range of 1~9 wt% of organophilic synthetic layered silicate (STN). Firstly, poly(amic acid)/STN nanocomposite solutions were prepared via solution blending method in DMAc or THF/MeOH solution, and then cast on the polyester film followed by imidization reaction, thermal and chemical method repestively. XRD and TEM experiment showed that the STN was fully exfoliated through the polyimide matrix. Surface morphologies of nanohybridized polyimide films were characterized by AFM and thermal, mechanical properties were also confirmed by TGA, DMA and UTM each. And also, the water vapor permeabilities highly depended on the content of STN. The sample from chemical imidization route and THF/MeOH solvent system showed better water vapor barrier properties than thermal one and DMAc system.

• Journal of the Korean Chemical Society
• /
• v.62 no.2
• /
• pp.118-123
• /
• 2018

The hexagonal tungsten bronze $Cs_xWO_3$ nanoparticle was synthesized by a chemical coprecipitation method of ammonium tungstate and $Cs_2CO_3$ in acidic condition. This synthetic method for cesium tungsten bronze is reported for the first time as far as we know. The synthesized $Cs_xWO_3$ as precipitated showed a weak crystallinity of hexagonal unit cell with a crystallite size of about 4 nm without annealing. When the synthesized $Cs_xWO_3$ was annealed in $N_2$ atmosphere, the crystallinity and crystallite size systematically increased maintaining the typical hexagonal tungsten bronze structure as the annealing temperature increased. The analyzed Cs content in the bronze was about 0.3 vs W, which is very close to the theoretical maximum value, 1/3 in cesium tungsten bronze. According to XPS analysis, the reduced tungsten ions existed as both the forms of $W^{5+}$ and $W^{4+}$ and the contents systematically increased as the annealing temperature increased up to $800^{\circ}C$. The $Cs_xWO_3$ thin films on PET substrate were also prepared by a wet-coating method using the ball-milled solution of the annealed $Cs_xWO_3$ nanoparticles at various temperatures. The near-infrared shielding property of these thin films increased systematically as the annealing temperature increased up to $800^{\circ}C$ as expected with the increased contents of reduced tungsten ions.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.4
• /
• pp.187-193
• /
• 2018

In this study, the electrical conductivity, transmittance and gas barrier properties of diamond-like carbon (DLC) thin films were studied. DLC is an insulator, and has transmittance and oxygen gas barrier properties varying depending on the thickness of the thin film. Recently, many researchers have been trying to apply DLC properties to specific industrial conditions. The DLC thin films were deposited by PECVD (Plasma Enhanced Chemical Vapor Deposition) process. The doping gas was used for the DLC film to have electrical conductivity, and the optimum conditions of transmittance and gas barrier properties were established by adjusting the gas ratio and DLC thickness. In order to improve the electrical conductivity of the DLC thin film, $N_2$ doping gas was used for $CH_4$ or $C_2H_2$ gas. Then, a heat treatment process was performed for 30 minutes in a box furnace set at $200^{\circ}C$. The lowest sheet resistance value of the DLC film was found to be $18.11k{\Omega}/cm^2$. On the other hand, the maximum transmittance of the DLC film deposited on the PET substrate was 98.8%, and the minimum oxygen transmission rate (OTR) of the DLC film of $C_2H_2$ gas was 0.83.

• Textile Coloration and Finishing
• /
• v.8 no.2
• /
• pp.56-63
• /
• 1996

Low-temperature plasma treatment or sputter etching is of interest as one of the techniques to modify polymer surface. In this study, poly(ethylene terephthalate)(PET), nylon 6 and cotton fabrics dyed three black dyes were subjected to low-temperature argon plasma and also sputter etching. In relation to bathochromic effect, the surface characteristics of the treated fabrics and films were investigated by means of critical surface tension, SEM and ESCA measurement. The depth of shade of fabrics more increased by the sputter etching technique than argon plasma treatment. Many microcraters on the fiber surface formed by the sputter etching resulted in increase of surface area of the fiber and wettability, but the hydrophobic group was increased by the results of ESCA analysis. In particular the change in reflective index of the fibers was much more effective than the chemical composition of the fiber surface on increasing of the depth of shade.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.77-77
• /
• 2003

디스플레이 소재나 자동차 글레이징 소재에 있어서 경량화나 충격성을 향상시키기 위하여 플라스틱소재를 기재로 응용하는 연구가 진행되고 있다. 본 연구에서는 폴리에틸렌테레프탈레이트(PET)와 폴리카보네이트(PC) 고분자 필름의 내마모성, Haze 성, 내수증기 차단성 등을 향상시키기 위하여 유기실리콘 전구체인 HMDSO 모노머와 산소를 사용하여 플라즈마 도움화학증착(PECVD) 하였다. RF출력과 HMDSO 투입량, 산소투입량을 변화시키면서 각 증착조건에 따른 생성된 필름의 화학결합구조와 표면조도, 헤이즈 특성에 미치는 영향을 FTIR-ATR, AFM, Hazemeter를 이용하여 알아보았다. HMDSO와 산소를 사용한 박막의 증착은 100 nm/min이상의 높은 증착속도를 가졌고, 증착실험에서 얻은 증착필름의 원소조성을 XPS를 이용하여 구한 결과, 종전의 다른 유기실리콘계 모노머를 사용했을 때보다 효과적으로 박막에 존재하는 탄소잔류물을 감소시키는 것을 확인하였으며, FTIR-ATR결과로 부터 플라스틱 기재의 차이로 인한 생성박막의 결합구조가 다름을 알 수 있었다. 본 연구로부터 HMDSO/02 시스템이 탄소함량이 낮은 박막을 형성시키고 내마모도가 좋은 박막을 증착시키는데 효과적인 것을 알 수 있었다.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1353_1354
• /
• 2009

The OTFT devices had inverted staggered structures of Au/pentacene/ppMMA/ITO on PET substrate. The overall device performances of the flexible devices such as the operating voltage, the field effect mobility, the on/off ratio and the off current are somewhat worse than those of devices fabricated on glass substrates. Pentacene/ppMMA OTFT benchmarks (mobility, sub-threshold slope, on/off ratio) were comparable to that of solution cast PMMA, but below average when compared to other polymer gate dielectrics. However, threshold and drive voltages were among the lowest reported for a polymer gate dielectric, and surpassed only by ultra-thin SAM gate dielectrics.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.10
• /
• pp.773-777
• /
• 2009

In this study, the strain sensing characteristics of single-wall carbon nanotubes(SWCNTs) networks were investigated to develop a film sensor for strain sensing. The SWCNTs film are formed on flexible substrates of poly(ethylene terephthalate) (PET) using spray process. In this manner we could control the transparency and obtain excellent uniformity of the networked SWCNT film. The carbon nanotube film is isotropic due to randomly oriented bundles of SWCNTs. Using experimental results it is shown that there is a nearly linear change in resistance across the film when it is subjected to tensile stress. The results presented in this study indicate the potential of such films for high sensitive transparent strain sensors on macro scale.

• Textile Coloration and Finishing
• /
• v.3 no.4
• /
• pp.22-28
• /
• 1991

Perfluoropropene was plasma polymerized in the form of thin film on PET fabrics to give hydrophobic and barrier properties without affecting air permeability. Changes in surface characteristics were detected by application of ESCA, IR, SEM and contact anglemeter. The surface properties was changed markedly to be water and stain repellent although the effect was not much sensitive to the differences of chemical components of the thin films formed at different experimental conditions. The protective barrier characteristics of the thin film was also applicable to suppress the amounts of dyes extracted from fabrics in laundering.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1153-1154
• /
• 2015

In this study, electro-polymerization was used for coating PEDOT:SDS films on CNTs, thereby producing hybrid-type electrodes. The CNTs were deposited on PET substrates using a spray method. For the fabricated hybrid electrodes, their surface morphologies, electric sheet resistances, visible transmittances, and chromatic properties were characterized as functions of the polymerization conditions used for coating PEDOT, and compared with those of conventional CNTs. The experiment results confirmed that the sheet resistance of CNTs was decreased significantly by coating of PEDOT via electropolymerization, and also indicated that the fabricated hybrid electrodes revealed desirable properties as a transparent electrode for touch screen panels.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.8-8
• /
• 2010

본 발표에서는 OLED, LCD, E-ink 등에 적용되는 고품질 전도성 투명 산화막의 구조, 전기적 성질, 광학적 성질, 표면 거칠기 등에 미치는 공정 변수의 영향을 유연 기판 적용 사례를 들어서 설명한다. 특히 RF superimposed dc sputtering 방법으로 성장시킨 TCO의 특성이 현재 알려진 어떤 방법보다도 우수한 특성들과 유연 기판에 필수적인 내절성을 갖는 결과를 보여주고 있음에 주목하고 그 원리 및 대형화 가능성에 대해서 언급한다. 증착된 박막의 투습성 평가에서 측정 장비의 한계치 이하를 달성하였고 플라즈마를 이용한 중간 처리 과정의 효과로 PC, PET 등의 필름 기판에서도 우수한 성질을 갖는 박막의 성공적인 증착이 이루어 졌음을 설명한다. 여기에는 적절한 산소 분압의 유지가 관건이며 이미 재료연구소에서는 대형 타겟 시스템에 대해서 안정된 공정을 운영하고 있다. RF superimposed dc power의 특징은 타겟에서 반사되는 고속 중성 입자의 유속을 적절하게 제어할 수 있다는 점으로 판단되며 이는 주로 산소 원자와 산소 음이온의 에너지가 높다는 점에 주목할 필요가 있다. Carcia등의 보고에 따르면 산소 음이온의 경우에는 110 eV가 넘는 운동 에너지를 가지고 성장 중인 박막에 입사하여 결함을 생성한다고 한다. 이들 고속 입자들의 에너지를 낮추고 그 수를 감소시킬 수 있는 방법 중의 하나가 RF superimposed dc라고 판단된다.