• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.230-236
• /
• 2017

Solubility data of carbon dioxide ($CO_2$) in poly(ethylene glycol) dimethyl ether (PEGDME) are presented at pressures up to about 50 bar and at temperatures between 303 K and 343 K. The solubilities of $CO_2$ were determined by measuring the bubble point pressures of the $CO_2+PEGDME$ mixtures with various compositions using a high-pressure equilibrium apparatus equipped with a variable-volume view cell. To observe the effect of the PEGDME molecular weight on the $CO_2$ solubility, the $CO_2$ solubilities in PEGDME with two kinds of molecular weight were compared. As the equilibrium pressure increased, the $CO_2$ solubility in PEGDME increased. On the other hand, the $CO_2$ solubility decreased with increasing temperature. When compared at the same temperature and pressure, the PEGDME with a higher molecular weight gave smaller $CO_2$ solubility on a mass fraction and molality basis, but gave greater $CO_2$ solubilities on a mole fraction basis.

• Polymer(Korea)
• /
• v.25 no.4
• /
• pp.568-574
• /
• 2001

PEO-like solid polymer electrolytes based on bisphenol A ethoxylate acrylate were synthesized and their electrochemical properties and mechanical stability were studied. Low molecular weight poly(ethylene glycol) dimethyl ether (PEGDMe) was added to increase the conductivity of the electrolyte. The maximum conductivity of the resulting polymer electrolyte was found to be 1.0 ${\times}$ 10$^{-3}$ S/cm [Bisphenol A ethoxylate diacrylate ([EO]/[phenol]= 15), PEGDMe250 80 wt%, LiCF$_3SO_3$] at 30$^{\circ}$C. Tensile strength of the free standing polymer electrolyte films was measured to be in the range of 0.4 ~ 5 MPa and these polymer electrolyte films did not show a crack even in 90$^{\circ}$ and 180$^{\circ}$ bending against ${\phi}$=3 mm bar. These electrolytes showed oxidation stability up to 4.5 V vs. lithium reference electrode.

• Macromolecular Research
• /
• v.12 no.5
• /
• pp.431-436
• /
• 2004

Cross-linked network solid polymer electrolytes were prepared by means of in situ hydrosilylation between poly[hydromethylslioxane-g-oligo(ethylene oxide)] and diallyl or triallyl group-containing poly(ethylene glycols). The conductivities of the resulting polymer electrolytes were greatly enhanced upon the addition of poly(ethylene glycol) dimethyl ether (PEGDME) as an ion-conducting plasticizer. Conductivities of the cross-linked polymer electrolytes were more dependent on the molecular weight of PEGDME than on the cross-linkers. The maximum conductivity was found to be 5.6${\times}$10$\^$-4/ S/cm at 30$^{\circ}C$ for the sample containing 75 wt% of PEGDME (M$\_$n/ =400). These electrolytes exhibited electrochemical stability up to 4.5 V against the lithium reference electrode. We observed reversible electrochemical plating/stripping of lithium on the nickel electrode.

• Macromolecular Research
• /
• v.9 no.6
• /
• pp.332-338
• /
• 2001

Waterborne polyurethane as a new polymer electrolyte was synthesized by using relatively hydrophilic polyols. The morphology of polyurethane was changed as it was dispersed in water. In contrast to polyurethane ionomer, waterborne polyurethane did not form an ionic cluster but produced a binary system composed of hydrophilic and hydrophobic groups. In the colloidal system, the former and the latter existed at outward and inward, respectively. Waterborne polyurethane was prepared from poly(ethylene glycol) (PEG) /poly(propylene glycol) (PPG) copolymer, 4,4'-diphenylmethane diisocyanate(MDI), ethylene diamine as a chain extender, and three ionization agents, 1,3-propane sultone, sodium hydride and lithium hydroxide. PEG/PPG copolymer was used for suppressing the crystallinity of PEG and N-H bond was ionized for increasing the electrochemical stability of polyurethane. Low molecular weight poly(ethylene glycol) and poly(ethylene glycol dimethyl ether) (PEGDME) were used as plasticizers. DSC, FT-IR and $^1$H-NMR of the waterborne polyurethane were measured. Also, the ionic conductivity of solid polymer electrolytes based on waterborne polyurethane and various concentrations of low molecular weight poly(ethylene glycol) or PEGDME were measured by AC impedance.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.4
• /
• pp.259-269
• /
• 2002

A battery based on the lithium/elemental sulfur redox couple has the advantage of high theoretical specific capacity of 1,675 mAh/g-sulfur. However, Li/S battery has bad cyclic durability at room temperature due to sulfur active material loss resulting from lithium polysulfide dissolution. To improve the cycle life of Li/S battery, PEGDME (Poly(ethylene glycol) dimethyl ether) 500 containing 1M LiTFSI salt which has high viscosity was used as electrolyte to retard the polysulfide dissolution and nano-sized $Mg_{0.6}Ni_{0.4}O$ was added to sulfur cathode as additive to adsorb soluble polysulfide within sulfur cathode. From experimental results, the improvement of the capacity and cycle life of Li/S battery was observed( maximum discharge capacity : 1,185 mAh/g-sulfur, C50/C1 = 85 % ). Through the charge-discharge test, we knew that PEGDME 500 played a role of preventing incomplete charge-discharge $behavior^{1,2)$. And then, in sulfur dissolution analysis and rate capability test, we first confirmed that nano-sized $Mg_{0.6}Ni_{0.4}O$ had polysulfide adsorbing effect and catalytic effect of promoting the Li/S redox reaction. In addition, from BET surface area analysis, we also verified that it played the part of increasing the porosity of sulfur cathode.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.629-630
• /
• 2014

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.4
• /
• pp.334-339
• /
• 2013

In this study, as a candidate of the carbon dioxide ($CO_2$) absorbents, the mixture solution of polyethylene glycol dimethyl ether (PEGDME) and tetrahydrofuran (THF) were investigated. $CO_2$ absorption rate was measured by using high pressure $CO_2$ screening equipment in the range of 1 - 10wt% THF. Absorption capacity of the mixture solution was also estimated. Based on the results, we found that mixture solution containing THF had higher absorption rate and $CO_2$ loading capacity compared to PEGDME at $25^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.10
• /
• pp.3555-3556
• /
• 2011

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.24-27
• /
• 2009

Solid-state dye-sensitized solar cells (DSSCs) have been constructed employing supramolecular electrolytes with multiple hydrogen bonding. A supramolecule was facilely synthesized by one-pot reaction between the amines of methyl isocytosine (MIC) and the epoxy groups of poly(ethylene glycol diglycidyl ether) (PEGDGE) to produce quadruple hydrogen bonding units. Hydrogen bonding interactions and dissolution behavior of salt in supramolecular electrolytes are investigated. The ionic conductivity of the supramolecular electrolytes with ionic liquid, i.e. 1-methyl-3-propylimidazolium iodide (MPII) reaches $8.5{\times}10^{-5}$ S/cm at room temperature, which is higher than that with metal salt (KI). A worm-like morphology is observed in the FE-SEM micrographs of $TiO_2$ nanoporous layer, due to the connection of $TiO_2$ nanoparticles resulting from adequate coating by electrolytes. DSSCs employing the supramolecular electrolytes with MPII and KI exhibit an energy conversion efficiency of 2.5 % and 0.5 %, respectively, at 100 $mW/cm^2$, indicating the importance of the cation of salt. Solar cell performances were further improved up to 3.7 % upon introduction of poly(ethylene glycol dimethyl ether) (PEGDME) with 500 g/mol.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.306-308
• /
• 2007

Poly(ethylene glycol) dimethyl ether (PEGDME)/fumed silica/ 1-methyl -3-propylimidazolium iodide (MPII)/$I_2$ mixtures were used as polymer electrolytes in solid state dye-sensitized solar cells (DSSCs). The contents of MPII were changed and the concentration of $I_2$ was fixed at 0.1 mole% with respect to the MPII. The maximum ionic conductivity was obtained at [EG]:[MPII]:[$I_2$]=10:1.5:0.15. It was supposed that the maximum of ionic conductivities would match with that of cell efficiencies, if the ionic conductivity is a rate determining step in the sol id state DSSCs. However, the maximum composition did not show the maximum solar cell performance, indicating the mismatch between ionic conductivity and cell performance. This suggests that the ionic conductivity may not be the rate controlling step in determining the cell efficiency in these experimental conditions, whereas other parameters such as the electron recombination might play an important role. Thus, we tried to modify the surface of the $TiO_2$ particles by coating a thin metal oxide such as $Al_2O_3$ or $Nb_2O_5$ layer to prevent electron recombination. As a result, the maximum of the cell efficiency was shifted to that of the ionic conductivity. The peak shifts were also attempted to be explained by the diffusion coefficient and the lifetime of electrons in the $TiO_2$ layer.