• The Korean Journal of Food And Nutrition
• /
• v.19 no.4
• /
• pp.358-365
• /
• 2006

To study simultaneous water and solute transport kinetics during soaking in concentrated solution, the influence of the concentration and molecular weight of the solute(polyethylene glycol(PEG) and NaCl) in the soaking solution and the temperature on the water loss and solute gain rates were observed by using a model vegetable tissue(potato). When potato slices$(4cm{\times}4cm{\times}0.1cm)$ soaked in 60% PEG solutions, the water loss rate of the early phase decreased with increasing of the molecular weight of PEG from 200 to 6,000, while the final water loss increased with increasing the molecular weight of PEG and it reached to 80%. The cell wall of potato tissue was permeable to NaCl and PEGs of which average molecular weight is smaller than 400 but it was not permeable to PEG 600 and larger molecules. PEG which has average molecular weight below 600 induced plasmolysis and those above 600 induced cytorrhysis. The water loss rate of potato sample soaked in smaller molecular weight PEG solution was faster than those soaked in higher molecular weight PEG solution before cytorrhysis happened. The water loss rate was reversed after cytorrhysis happened. The volume change of potato within the first 60 minutes was larger in low molecular PEG solution but the final ratio of decreasing volume was larger in high molecular PEG solutions. In PEG 200 solution, the potato tissue was slightly shrinked without shape change. However, in PEG 4,000 solution, volume of potato was reduced significantly and potato tissue was twisted.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.5
• /
• pp.465-472
• /
• 1994

To improve the germination performance of rice seeds under suboptimal temperature, osmopriming with PEG-6000 was examined. Optimal PEG-6000 concentration to improve germination was 20% PEG-6000 solution, and rice cultivars used in this experiment were Sinunbongbyeo, Gancheokbyeo, Dongjinbyeo. The water content of seeds after soaking for 60 hours in the PEG solution is similar to that of seeds after soaking for 24 hours in the distilled water. Germination performance of the soaked seeds in the PEG solution was higher than that of the soaked seeds in the distilled water or the control, especially under suboptimal temperatures. Electrical conductivity of the soaked seeds in the PEG solution was lower than that of the soaked seeds in the distilled water or the control, and total dehydrogenase activity of the soaked seeds in the PEG solution was higher than that of the soaked seeds in the distilled water or the control. SDS-PAGE results of soluble protein from the embryos of seeds primed differently showed darker band in the seeds soaked in the PEG solution than the seeds soaked in the distilled water or the control at the 68 KD region. Also, band patterns of peroxidase and esterase of embryos soaked in the PEG solution were darked than that of embryos soaked in the distilled water or the control at the Rf 0.94 and Rf 0.87, respectively.

• YAKHAK HOEJI
• /
• v.29 no.5
• /
• pp.234-245
• /
• 1985

To clarify the diffusional behavior of p-aminbenzoic acid esters in the presence of polyethylene glycol 400, cellulose membrane permeation rate, solubility and viscosity of p-aminobenzoic acid methyl ester, benzocaine and butamben were determined with PEG solutions of various concentrations. With an increase in PEG concentrations permeation rates from solutions; decreased due to an increase in viscosity of the solution. From suspensions, however, permeation rates increased due to an increase in solubility and when the initial drug concentration was constant, permeation rates were found to be greatest from the PEG-water system with the PEG concentration which transported from the solution to the suspension. Permeation rate of 4.0mg/ml p-aminobenzoic acid methyl ester was $26.51\mu$g/ml$\cdot$hr from 5g/100ml PEG solution, and that of 4.0mg/ml benzocaine was $13.17{\mu}g/ml{\cdot}hr$ from 15g/100ml PEG, solution, and that of 2.0mg/ml butamben was $3.8{\mu}g/ml{\cdot}hr$ from 10g/100ml PEG solution. Permeation rate was 7.0 fold in p-aminobenzoic acid methyl, ester and 3.5 fold in benzocaine compared to butamben.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.70-79
• /
• 1998

The PEG and PCP have been used as a binder of high energy and minimum smoke propellant. In this study, PEG, PCP 0260, PCP 1270 and mixed PEG/PCP as a prepolymer were used, and also used BTTN/DEGDN and BTTN/TMETN as a plasticizer. Before being cured, the solution viscosity of prepolymer and plasticizer was measured with various contents of PCP in PEG and contents of plasticizer at $20^{\cire}C$~$60^{\cire}C$. The results were shown the increased concentration of PCP enhanced the viscosity of solution due to the hydrogen bond of PCP, and the increased contents of plasticizer undoubtedly decrease the viscosity of solution. The cured binders were tested for mechanical properties and measured for glass transition temperature with various concentration of PCP in PEG and contents of plasticizer. The increased concentration of PCP has shown better mechanical properties. This results were attributed to the H-bond. Also, the glass transition temperature was lowered with the higher contents of PCP Finally, with the higher content of PCP in PEG, the better mechanical properties and the lower glass transition temperature and the higher viscosity of solution were shown.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12
• /
• pp.1125-1130
• /
• 2003

The electrophoretic deposition method using the suspension solution with additives under the electric potential was applied for the fabrication of YBCO superconductor wire. This method was able to simplify the fabrication facilities, and produce an uniform and dense thick film. To improve the critical current density of deposited films, the additive PEGs(Poly Ethylene Glycole) with the molecular weight of 600, 1000 and 3400 were used as chemical binders for the suspension solution. The organic additive (PEG) showed better effects to the properties of YBCO superconductor wire. The PEG improved the adhesion between superconductor particles and suppressed the crack on the surface, which enhanced the surface uniformity and density of YBCO deposited film. It was found that acetone suspension solution showed better deposition properties than the others. The samples fabricated in the solution with the additive, 8 vol.% of 1% PEG(1000), showed the highest critical current density measured as 2300∼2400 A/$\textrm{cm}^2$ at 77 K, 0 T.

• Conservation Science in Museum
• /
• v.1
• /
• pp.27-35
• /
• 1999

To get the best result from vacuum freeze drying of water-logged wood, it is necessary for objects to find out the best conditions such as chemicals, appropriate concentration of solution, impregnation method and etc. Such best conditions could be set up by pre-treatment experiments. Two kinds of wood(Pinus densiflora S. et Z. and Quercus acutissima Carruth) were pre-treated by four methods: 2-step PEG treatment(PEG#200-PEG#4000), sorbitol treatment, PEG#200+PEG#4000 treatment, and sorbitol+PEG#4000 treatment. After those pre-treatment, vacuum freeze-drying was undertaken. Then the effect of dimensional stability were compared. When using 2-step PEG treatment, a solution of 60% PEG #4000 got the best dimensional stability for pine and in case of the oak, a solution of 40% PEG#4000 got the best. Sorbitol treatment got rather good result for the pine only when applied with 40% solution of sorbitol. Sorbitol, PEG#200+PEG#4000 and sorbitol+PEG#4000 treatments to the oak didn't affect on dimensional stability sufficiently.

• Journal of Pharmaceutical Investigation
• /
• v.26 no.2
• /
• pp.99-103
• /
• 1996

Effects of glycerin and PEG 400 in donor and receptor solutions upon skin permeation of drug were investigated. Deoxycortisone was used as a model compound. In vitro skin permeation study with freshly excised hairless mouse skin was performed and the steady-state skin permeation rates of the drug were determined in different fractions of glycerin or PEG 400 in donor and receptor solutions. Glycerin in donor solution didn't show any effect on the skin permeation rate of deoxycortisone. However glycerin in receptor solution showed significant effect on the skin permeation rate of the drug. In glycerin, there's a critical concentration for balancing hydration and dehydration of skin. At low concentration, less than 20 %, glycerin showed the enhancement of the flux due to the hydration effect of skin. At high concentration, more than 30 %, glycerin retard the permeation rate which might be due to the dehydration effect on the dermis layer. Since dermis has more water content than the stratum corneum, the steady state skin permeation rates were more influenced when glycerin was in receptor solution than that of in donor solution. PEG 400 aqueous solutions doesn't affect the steady state permeation rate of deoxycortisone significantly.

• Journal of Conservation Science
• /
• v.28 no.2
• /
• pp.95-99
• /
• 2012

The compressive strength of PEG along processing concentration and solvent is willing to be measured and proper processing condition for exhibition and storage is also willing to be measured by comparing with dimensional stability. In the advanced research of setting PEG-preprocessing concentration & solvent for freeze drying of waterlogged archaeological wood of high water content, vacuum freeze drying showed the highest dimension stability after 40% PEG-preprocessing of aqueous solution. In this study, the compressive strength increased in proportion of processing concentration and water showed the relatively-higher compressive strength than t-butanol regarding solvent. Especially, it showed that there is no big strength difference between PEG 40% and PEG 50% in aqueous solution by 6.6%(16kgf/$cm^2$). According to the above results, it was recognized that it is most effective to implement freeze drying after 40% PEG-preprocessing when want to dimensional stability and compressive strength simultaneously.

• Biomaterials and Biomechanics in Bioengineering
• /
• v.2 no.1
• /
• pp.15-22
• /
• 2015

Poly(ethylene glycol) end-capped with pentafluorophenyl group(s) in ABA (FP-PEG-FP) and AB (mPEG-FP) types were prepared. Even though they were similar in composition, the lower critical solution temperature (LCST) of FP-PEG-FP was observed at $23^{\circ}C$, whereas that of mPEG-FP was observed at $65^{\circ}C$. To understand the large difference in solution behaviour of the two polymers, UV-VIS spectroscopy, microcalorimetry, 1H-NMR spectroscopy, and dynamic light scattering were used. FP-PEG-FP has two hydrophobic pentafluorophenyl groups at the ends of hydrophilic PEG (1000 Daltons), whereas mPEG-PF has a highly dynamic PEG (550 Daltons) block that are anchored to a hydrophobic pentafluorophenyl group. PF-PEG-PF not only has a smaller conformational degree of freedom than mPEG-PF but also can form extensive intermolecular aggregates, therefore, PF-PEG-PF exhibits a significantly lower LCST than mPEG-PF. This paper suggests that topological control is very important in designing a temperature-sensitive polymer.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.47-48
• /
• 2011

The effect of solution acidity and organic additives, polyethylene glycol (PEG), on the trivalent chromium electroplating was systematically investigated in the view point of solution stability, electroreduction of trivalent chromium ions and characterization of deposition layer. It was found that, the concentration of fraction chromium complexes in the trivalent chromium bath containing formic acid is strongly depended on pH value. PEG molecules were stable in trivalent chromium bath containing formic acid via studies on electrospray ionization mass spectrometry (ESI-MS) and UV-Vis. However, the presence of PEG molecules decreased the reductive current of hydrogen evolution, increasing of current efficiency higher about 10 % compared with solutions without PEG. Moreover, PEG additives developed the nodular morphology during electroreduction of trivalent chromium ions with the increase of solution acidity and enhanced its current efficiency by maintaining the consumption of complexant, formic acid, at a low speed. In this study, the effect of solution acidity was emphasized important, there, it controlled the formation of complexes in the solution, cathodic film (CF) during deposition, and properties of deposited layer. By electrochemical quartz crystal microbalance (EQCM), studies show that chromium electrodeposition occurs via the formation of intermediate complexes and adsorption on the cathode surface, which hinder the penetration of ions from bulk solution to the cathode surface.