• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.462-465
• /
• 2011

A pulse oximeter is a device which provides non-invasive estimate of percentage oxygen saturation of haemoglobin (SpO2). Due to the limitations of resources of personal health devices (PHDs) including pulse oximeters, they generally transmit the estimated data to a remote monitoring server through a close manager (e.g. mobile device or PC). Therefore, communication protocols between PHDs and a manager is an important research topic in terms of interoperability. In this paper, we present design results of an SpO2 transmission agent based on the ISO/IEEE 11073 (X73) protocol. The protocol is an international standard for PHDs. The agent is an embedded program which generates X73 messages from the estimated pulse rates and SpO2, and transmits the messages to a close manager. The agent consists of a Session, Message and Memory Handler. The Session Handler manages a communication session with the manager, and the Message Handler generates and analyzes the exchanged messages according to the X73 protocol. The Memory Handler extracts pulse rates and SpO2s which are stored in a memory of the pulse oximeter. The SpO2 transmission agent allows pulse oximeters to communicate with managers based on x73 standard. Consequently, the interoperability between the pulse oximeters and the managers is guaranteed.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.1
• /
• pp.203-209
• /
• 2019

In this work, a new land-specific resistance measuring device (GM) and a measuring probe (Grounding Rod) are connected to the WENNER quadrant as power-line communication (PLC). In groups of two (P1,P2) probes, five to ten probes are installed in series on the ground at intervals of 1m, 2m, 4m, 8m, and 16m, respectively. If the PLC signal from the GMD is detected by the receiver of the Probe 1 (P1) for measurement, the minute voltage and current for measurement flow from the PSD (power supply) attached to the probe to the ground, and then, through the soil between P1 and P2, enters the Probe 1 (P2). The resistance value is then measured by the principle of voltage drop due to ground resistance. Measure the earth resistance every T seconds up to 1 trillion and store the measured data on the Arduino Server mounted on the main equipment. Stored measurement data can be derived from formulas by Ohm's Law and from inherent resistance (here,). Data obtained in real time will be linked to CDGES programs installed on Main PC, enabling data analysis and real-time monitoring of the ground environment on land. In addition, a three-dimensional display is possible with 3D graph support by identifying seasonal characteristics such as temperature and humidity of land (soils). The limitations of the study will require specific application measures of Test Bed for commercial access to a model that has been developed and operated experimentally.

• Annals of Clinical Neurophysiology
• /
• v.1 no.1
• /
• pp.26-30
• /
• 1999

Background : The origin of P300 was still on debate nbut thought to be in the frontal, temporal or parietal lobe. As the transcranial doppler ultrasonography(TCD) gives us and opportunity to observe hemodynamic chaged dynamically and the middle cerebral artery feeds these ares of the hemisphere, we observed the change of mean flow velocity of MCA during the event related potential test(ERP) to determine the role of these structures in P300 generation. Method : Twenty normal subjects(male : 13, age : 24-29 years) performed ERP. An auditory oddball pardigm was used to elicit the ERPs. TCD examination was performed with 2-MHz probe monitoring the left MCA(Transscan, EME). After signal identification and adjustments to maximize the Doppler signal strength, the probe was mechanically locked during the monitoring. The changes of blood flow velocity of the left middle cerebral artery(MCA) induced by cognitive demands were monitored. The measurement of the meal flow velocities(MFV) of MCA were made while the subjects were prior to, during, and after ERP. We recorded the MFVs during ERP. Statistical analysis was performed using t-tests with SPSS-PC for windows release 6.0. Results : All subjects showed a relative increase in MFV of MCA during the task. The mean rise was about 3.2-4.2%(p <0.05). Although TCD does not measure absolute values of regional cerebral blood flow(rCBF) or absolute rCBF changes, changes of flow velocity can reflect relative rCBF changes. Conclusions : The generation site of P300 still remains unclear but the neocortical, thalamic and limbic region and temporal-parietal cortex have been proposed. The MCA supplies these anatomical structures. The Changes of flow veolocity of MCA during the ERP test suggest that the some part of the brain fed y the MCA activate of the temporal lobe or parietal lobes, we can deduce that some parts of brain fed by the MCA participate in the generation of P300.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.3104-3104
• /
• 2001

The research described here was undertaken with the aim of monitoring, optimizing and ultimately controlling the production of heterofermentative microbes used as starters in the salami industry. The use of starter cultures in the fermented meats industry is a well-established technique used to shorten and standardize the ripening process, and to improve and control the organoleptic quality of the final product. Starter cultures are obtained by the submerged cultivation of suitable microorganisms in stirred, and sometimes aerated, fermenters where monitoring of key physiological parameters such as the concentration of biomass, substrates and metabolites suffers from the general lack of real-time measurement techniques applicable to aseptic processes. In this respect, the results of the present work are relevant to all submerged fermentation processes. Previous work on the application of on-line NIR spectroscopy to the lactic acid fermentation (Dosi et al. - Monreal NIR1995) had successfully used a system based on a measuring cell included in a circulation loop external to the fermenter. The fluid handling and sterility problems inherent in an external circulation system prompted us to explore the use of an in-line system where the NIR probe is immersed in the culture and is thus exposed to the hydrodynamic conditions of the stirred and aerated fluid. Aeration was expected to be a potential source of problems in view of the possible interference of air bubbles with the measurement device. The experimental set-up was based on an in-situ sterilizable NIR probe connected to the instrument by means of an optical fiber bundle. Preliminary work was carried out to identify and control potential interferences with the measurement, in particular the varying hydrodynamic conditions prevailing at the probe tip. We were successful in defining the operating conditions of the fermenter and the geometrical parameters of the probe (flow path, positioning, etc.) were the NIR readings were reliable and reproducible. The system thus defined was then used to construct and validate calibration curves for tile concentration of biomass, carbon source and major metabolites of two different microorganisms used as salami starters. Real-time measurement of such parameters coupled with the direct interfacing of the NIR instrument with the PC-based measurement and control system of the fermenter enabled the development of automated strategies for the interactive optimization of the starter production process.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1088-1091
• /
• 2019

In this paper, a real-time monitoring system for environmental safety by living area is proposed. The proposed system is designed to measure radiation, fine dust and basic living information (temperature) using fixed and mobile measuring equipment, and constitutes a web database that stores data received from the equipment. It also develops web programs for displaying received data on PCs and mobile phones. The results of testing the performance of the system by an authorized testing agency showed that the radiation measurement range was measured in the range of $10{\mu}Sv/h$ to 10mSv/h, which is comparable to the world's highest level, and that the accuracy was measured between ${\pm}6.7$ and ${\pm}8.7$ percent of the measurement uncertainty was measured and normal operation at or below the international standard of ${\pm}15$ percent. In addition, the temperature test was conducted on a section of $-20^{\circ}C$ to $50^{\circ}C$ and normal operation was confirmed in response to the temperature change. Stability of radiated electromagnetic waves was ensured by a suitable judgment. The product's testing in general and high and low temperature environments for about four months after the prototype was made confirmed to be more than five years of durability. The measurement range and accuracy of fine dust sensors are compared with those of companies that measure the air environment, and the performance level is similar through the air quality measurement register.

• Convergence Security Journal
• /
• v.22 no.1
• /
• pp.93-98
• /
• 2022

Information service technology continues to develop, and information service continues to expand based on the IT convergence trend. The premeter-based security model chosen by many organizations can increase the effectiveness of security technologies. However, in the premeter-based security model, it is very difficult to deny security threats that occur from within. To solve this problem, a zero trust model has been proposed. The zero trust model requires authentication for user and terminal environments, device security environment verification, and real-time monitoring and control functions. The operating environment of the information service may vary. Information security management should be able to response effectively when security threats occur in various systems at the same time. In this study, we proposed a security policy distribution system in the object reference method that can effectively distribute security policies to many systems. It was confirmed that the object reference type security policy distribution system proposed in this study can support all of the operating environments of the system constituting the information service. Since the policy distribution performance was confirmed to be similar to that of other security systems, it was verified that it was sufficiently effective. However, since this study assumed that the security threat target was predefined, additional research is needed on the identification method of the breach target for each security threat.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1516-1519
• /
• 1997

With disseminationof Distributed Control Systems(DCS), the huge amounts of process operation data could have been available and led to figure out process behaviors better on the statistical basis. Until now, the statistical modeling technology has been susally applied to process monitoring and fault diagnosis. however, it has been also thought that these process information, extracted from statistical analysis, might serve a great opportunity for process operation improvements and process improvements. This paper proposed a general methodolgy for process operation improvements including data analysis, backing up the result of analysis based on the methodology, and the mapping physical physical phenomena to the Principal Components(PC) which is the most distinguished feature in the methodology form traditional statistical analyses. The application of the proposed methodology to the Balst Furnace(BF) process has been presented for details. The BF process is one of the complicated processes, due to the highly nonlinear and correlated behaviors, and so the analysis for the process based on the mathematical modeling has been very difficult. So the statisitical analysis has come forward as a alternative way for the useful analysis. Using the proposed methodology, we could interpret the complicated process, the BF, better than any other mathematical methods and find the direction for process operation improvement. The direction of process operationimprovement, in the BF case, is to increase the fludization and the permeability, while decreasing the effect of tapping operation. These guide directions, with those physical meanings, could save fuel cost and process operator's pressure for proper actions, the better set point changes, in addition to the assistance with the better knowledge of the process. Open to set point change, the BF has a variety of steady state modes. In usual almost chemical processes are under the same situation with the BF in the point of multimode steady states. The proposed methodology focused on the application to the multimode steady state process such as the BF, consequently can be applied to any chemical processes set point changing whether operator intervened or not.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.25 no.6
• /
• pp.1435-1447
• /
• 2015

Finance Companies are operating a security solution such as E-DRM(Enterprise-Digital Right Management), Personal information search, DLP(Data Loss Prevention), Security of printed paper, Internet network separation system, Privacy monitoring system for privacy leakage prevention by insiders. However, privacy leakages are occurring continuously and it is difficult to the association analysis about relating to the company's internal and external distribution of private document. Because log system operated in the separate and independent security solutions. This paper propose a systematic chains that can correlatively analyze business systems and log among heterogeneous security solutions organically and consistently based on security documents. Also, we suggest methods of efficient detection for Life-Cycle management plan about security documents that are created in the personal computer or by individual through the business system and distribution channel tracking about security documents contained privacy.

• Information Systems Review
• /
• v.7 no.2
• /
• pp.117-128
• /
• 2005

This study proposes an integrated monitoring system for data reliability improvement in a steel manufacturing industry. The data obtained from existing steel manufacturing process is not micro data which is gathered at the occurring point, but average value (macro data) which is gathered from the occurring point to ending point. This kind of macro data is not only difficult for a detailed analysis for an error causing factor, but it might cause a fatal influence as well on the quality of produced goods even if the error is within an error tolerance. And during the process of steel production, thousands of data is produced in a second, thus requiring database plan to manage abundant amount of data. Therefore, the following proposed system is capable of collecting as well as analyzing all the data generated from the process of product production. And the system was able to raise the efficiency of the database server by planning the database to handle large capacity data. Also, by applying web-based technology, inquiries and analysis of data with no limit on time and space was possible with PC connected to the intranet. Hence, the system was able to work on effective quality improvement of manufactured products, plus able to raise the reliability of the product. Also, accumulated data from long period of time was used for fundamental material for new controlling model, operation technology, and new product development.

• Journal of Sensor Science and Technology
• /
• v.13 no.5
• /
• pp.383-391
• /
• 2004

In this study, we implemented the pulse transit time (PTT) system to examine usefulness of the monitoring method of distensibility and elasticity using photoplethysmography sensor in vivo. PTT is defined as the time interval between the peak of QRS complex in ECG signal and the maximum slope point of photoplethysmography. these two signals were converted to digital data by means of AID converter, then PTT was evaluated by heartbeat using PC. Results of analysis were displayed as a graph using spline interpolation method. The variance of PTT was measured repetitiously to verify efficiency of PTT system in resting state and hyperemic state. Repeated measurement of PTT was not same value but showed that coefficients of correlation were related with each other as 0.8302 (P<0.01) in resting state. And also repeated measurement of PTT showed significant correlation as 0.868 (P<0.01) in the hyperemic state. These result showed that PTT is reflect on transient pressure variance in the artery and is very useful method for the evaluation of prognosis of the hypertension and arteriosclerosis.