• Journal of Korean Society for Atmospheric Environment
• /
• v.30 no.6
• /
• pp.577-585
• /
• 2014

A series of experiments using atmospheric-pressure non-thermal plasma coupled with transition metal catalysts were performed to remove ethylene from agricultural storage facilities. The non-thermal plasma was created by dielectric barrier discharge, which was in direct contact with the catalyst pellets. The transition metals such as Ag and $V_2O_5$ were supported on ${\gamma}-Al_2O_3$. The effect of catalyst type, specific input energy (SIE) and oxygen content on the removal of ethylene was examined to understand the behavior of the hybrid plasma-catalytic reactor system. With the other parameters kept constant, the plasma-catalytic activity for the removal of ethylene was in order of $V_2O_5/{\gamma}-Al_2O_3$ > $Ag/{\gamma}-Al_2O_3$ > ${\gamma}-Al_2O_3$ from high to low. Interestingly, the rate of plasma-catalytic ozone generation was in order of $V_2O_5/{\gamma}-Al_2O_3$ > ${\gamma}-Al_2O_3$ > $Ag/{\gamma}-Al_2O_3$, implying that the catalyst activation mechanisms by plasma are different for different catalysts. The results obtained by varying the oxygen content indicated that nitrogen-derived reactive species dominated the removal of ethylene under oxygen-lean condition, while ozone and oxygen atoms were mainly involved in the removal under oxygen-rich condition. When the plasma was coupled with $V_2O_5/{\gamma}-Al_2O_3$, nearly complete removal of ethylene was achieved at oxygen contents higher than 5% by volume (inlet ethylene: 250 ppm; gas flow rate: $1.0Lmin^{-1}$; SIE: ${\sim}355JL^{-1}$).

• Journal of Powder Materials
• /
• v.21 no.6
• /
• pp.447-453
• /
• 2014

Effect of oxygen content in the ultrafine tungsten powder fabricated by electrical explosion of wire method on the behvior of spark plasma sintering was investigated. The initial oxygen content of 6.5 wt% of as-fabricated tungsten powder was reduced to 2.3 and 0.7 wt% for the powders which were reduction-treated at $400^{\circ}C$ for 2 hour and at $500^{\circ}C$ for 1h in hydrogen atmosphere, respectively. The reduction-treated tungsten powders were spark-plasma sintered at $1200-1600^{\circ}C$ for 100-3600 sec. with applied pressure of 50 MPa under vacuum of 0.133 Pa. Maximun sindered density of 97% relative density was obtained under the condition of $1600^{\circ}C$ for 1h from the tungsten powder with 0.7 wt% oxygen. Sintering activation energy of $95.85kJ/mol^{-1}$ was obtained, which is remarkably smaller than the reported ones of $380{\sim}460kJ/mol^{-1}$ for pressureless sintering of micron-scale tungsten powders.

• Journal of Microbiology
• /
• v.44 no.3
• /
• pp.269-275
• /
• 2006

Atmospheric-pressure cold plasma (APCP) using helium/oxygen was developed and tested as a suitable sterilization method in a clinical environment. The sterilizing effect of this method is not due to UV light, which is known to be the major sterilization factor of APCP, but instead results from the action of reactive oxygen radicals. Escherichia coli, Staphylococcus aureus, and Saccharomyces cerevisiae deposited on a nitrocellulose filter membrane or Bacillus subtilis spores deposited on polypropylene plates were exposed to helium/oxygen plasma generated with AC input power at 10 kHz, 6 kV. After Plasma treatment, nitrocellulose filter membranes were overlaid on fresh solid media and CFUs were counted after incubation overnight. D-values were 18 sec for E. coli, 19 sec for S. aureus, 1 min 55 sec for S. cerevisiae, and 14 min for B. subtilis spores. D-values of bacteria and yeast were dependent on the initial inoculation concentration, while the D-value of B. subtilis spores showed no correlation. When treated cells were observed with a scanning electron microscope, E. coli was more heavily damaged than S. aureus, S. cevevisiae exhibited peeling, and B. subtilis spores exhibited shrunken morphology. Results showed that APCP using helium/oxygen has many advantages as a sterilization method, especially in a clinical environment with conditions such as stable temperature, unlimited sample size, and no harmful gas production.

• Korean Journal of Exercise Nutrition
• /
• v.13 no.1
• /
• pp.29-35
• /
• 2009

The purpose of this study was to investigate the effects of oral supplementation of coenzyme Q10 (CoQ10) for 4 weeks on the plasma free oxygen radical and total antioxidant capacity at resting and after one bout exercise in healthy old men. Thirty volunteers with an average (+/-SD) age of 62.59+/-5.3 years participated in this study and were divided with three groups; CoQ10 (200 mg daily) group, vitamin C & E (800mg, 400 IU daily) group, and placebo group. A cycle exercise (60% HRR) test was performed at the end of study. Blood samples were taken for the analyses at rest and pre-, post-, 30min after cycle exercise, before and after the 4 weeks of supplementation. After supplementation, there were no significant differences in the plasma free oxygen radical levels and total antioxidant capacity at resting. Plasma free oxygen radical level and total antioxidant capacity in three groups were significantly elevated after exercise, however, it did not vary significantly between groups. CoQ10 supplementation showed significant difference in total antioxidant capacity during recovery phase compared with placebo group. Our results demonstrated that supplementation of CoQ10 in healthy old men improve blood total antioxidant capacity after one bout exercise, despite no alteration of plasma free oxygen radical levels.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.4
• /
• pp.7-10
• /
• 2001

A new possibility of our atmospheric cold plasma torch has been examined on the surface treatment of an air-exposed vulcanized rubber compound. The plasma treatment effect was evaluated by the bondability with another rubber compound using a polyurethane adhesive. The adhesion property was improved by the treatment with plasma containing oxygen radicals. The oxygen radical generation from the plasma was verified and its efficiency was found to be dependent on the cathode material.

• Fashion & Textile Research Journal
• /
• v.16 no.3
• /
• pp.456-461
• /
• 2014

The objective of this study is to give PP(polypropylene) fabric a good affinity for water. Oxygen plasma was treated to PP fabrics in a commercial glow discharge reactor with different RF power, discharge pressure, and reaction time. The PP fiber surfaces were characterized by the measurement of contact angle and ESCA. A JEOL scanning electron microscope was used to observe the surface morphology of fibers. The spontaneous water uptake amount of PP fabrics was determined by the demand wettability test. To determine the effect of aging on the surface properties of $O_2$ plasma treated PP, all the above measurements of the samples were carried out after 1, 7, 30, 60, and 150 days. The results are as follows. The PP fiber surfaces treated by $O_2$ plasma treatment have a chemical composition that consisted of various oxygen containing polar groups. Consequently, the contact angles of the treated PP fibers decreased, which improved the water uptake rate of PP fabrics. Surface roughness of the treated PP affected the fabric wettabiity as well. Wettability of the treated PP decreased and leveled off with aging. The $O_2$ plasma treatment is a simple and effective method to increase the water uptake rate of PP fabrics.

• Applied Chemistry for Engineering
• /
• v.33 no.1
• /
• pp.38-43
• /
• 2022

The effect of introducing oxygen functional groups by oxygen plasma treatment of activated carbon on adsorption properties of cesium ions was investigated. During the oxygen plasma treatment, the frequency, power, and oxygen gas flow rates were fixed at 100 kHz, 80 W, and 60 sccm, respectively, while the reaction time was varied. Under the experimental conditions, the amount of cesium ion adsorption increased as the content of oxygen groups on C-O-C and O=C-O bonds increased when the reaction time with oxygen gas was 10 minutes. However, when the reaction time increased to 15 minutes, the oxygen functional group content decreased resulting in the decrease of the adsorbed cesium ion amount. On the other hand, unlike the oxygen content of the surface-treated activated carbon, the specific surface area and pore properties were hardly affected by the oxygen plasma reaction time. As a result, the oxygen plasma-treated activated carbon improved the cesium ion removal rate by up to 97.3% compared to that of the untreated activated carbon. This is considered to be due to the content of oxygen groups on C-O-C and O=C-O bonds introduced on the surface of the activated carbon through oxygen plasma treatment.

• Carbon letters
• /
• v.6 no.2
• /
• pp.106-110
• /
• 2005

In this work, the effects of atmospheric oxygen plasma treatment of carbon fibers on mechanical interfacial properties of carbon fibers-reinforced epoxy matrix composites was studied. The surface properties of the carbon fibers were determined by acid/base values, Fourier-transform infrared spectrometer (FT-IR), and X-ray photoelectron spectroscopy (XPS) analyses. Also, the crack resistance properties of the composites were investigated in critical stress intensity factor ($K_{IC}$), and critical strain energy release rate mode II ($G_{IIC}$) measurements. As experimental results, FT-IR of the carbon fibers showed that the carboxyl/ester groups (C=O) at 1632 $cm^{-1}$ and hydroxyl group (O-H) at 3450 $cm^{-1}$ were observed for the plasma treated carbon fibers, and the treated carbon fibers had the higher O-H peak intensity than that of the untreated ones. The XPS results also indicated that the $O_{1S}/C_{1S}$ ratio of the carbon fiber surfaces treated by the oxygen plasma led to development of oxygen-containing functional groups. The mechanical interfacial properties of the composites, including $K_{IC}$ (critical stress intensity factor) and $G_{IIC}$ (critical strain energy release rate mode II), were also improved for the oxygen plasma-treated carbon fibersreinforced composites. These results could be explained that the oxygen plasma treatment played an important role to increase interfacial adhesions between carbon fibers and epoxy matrix resins in our composite system.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.193-197
• /
• 2012

Oxygen plasma has been treated on the surface of indium-tin-oxide (ITO) to improve the efficiency of the organic light-emitting diodes (OLEDs) device. The plasma treatment was expected to inject the holes effectively due to the control of an ITO work-function and the reduction of surface roughness. To optimize the treatment condition, a surface resistance and morphology of the ITO surface were investigated. The effect on the electrical properties of the OLEDs was evaluated as a function of oxygen plasma powers (0, 200, 250, 300, and 450 W). The electrical properties of the devices were measured in a device structure of ITO/TPD/Alq3/BCP/LiF/Al. It was found the plasma treatment of the ITO surface affects on the efficiency of the device. The efficiency of the device was optimized at the plasma power of 250 W and decreased at higher power than 250 W. The maximum values of luminance, luminous power efficiency, and external quantum efficiency of the plasma treated devices increase by 1.4 times, 1.4 times, and 1.2 times, respectively, compared to those of the non-treated ones.

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.355-358
• /
• 2010

Inductively coupled low temperature plasmas with oxygen, argon, mixture of oxygen and argon, and nitrogen have been used to modify polycarbonate(PC) films at the various process conditions. All plasma treatments generally had a tendency to increase the surface roughness of PC regardless of process conditions. The treatment of oxygen plasma showed the highest value in the surface roughness and mostly enhanced the generation of oxygen containing polar groups as much as 43% in comparison of untreated PC. The contact angle of untreated PC decreased from $82.31^{\circ}$ to the lowest value of $9.17^{\circ}$ after oxygen plasma treatment. The increase of RF delivered power had an effect on the rapid reduction of contact angle, but gas flow rates did not effect to reduce contact angles so much.