• 한국표면공학회지
• /
• 제32권1호
• /
• pp.3-9
• /
• 1999

Pt thin film of about 7000$\AA$ thickness was deposited on the alumina substrate using DC Magnetron Sputter and the characteristics of the film for temperature sensor were investigated. When film of about 7000$\AA$ thickness was deposited at working gas pressure of $2.0{\times}10^{-3}$torr, sputtering power of 50W, substrate temperature of $350^{\circ}C$(Ts), sheet resistance(Rs), resistivity($\rho$) and temperature coefficient of resistivity(TCR) of the film were respectively 0.39$\Omega$/$\square$, 27.60$\mu\Omega$-cm and $3350 ppm/^{\circ}C$. When the film was annealed at $1000^{\circ}C$ for 240min in hydrogen ambient, Rs, $\rho$ and TCR were respectively 0.236$\Omega$/$\square$, 15.18$\mu\Omega$-cm and 3716 ppm/$3716 ppm/^{\circ}C$. When working gas of 15sccm oxygen and 100sccm Argon were used, Rs, $\rho$ and TCR were respectively 0.335$\Omega$/$\square$, 22.45$\mu\Omega$-cm and $3427 ppm/^{\circ}C$. When the film was annealed at $1000^{\circ}C$ for 240min, Rs, $\rho$and TCR were respectively 0.224/$\Omega$$\square$, 14$\mu\Omega$-cm and $3760 ppm/^{\circ}C$ and the characteristics of the film were much improved.

• 한국표면공학회지
• /
• 제45권3호
• /
• pp.117-122
• /
• 2012

ZTO/GZO double layered films were prepared on unheated non-alkali glass substrates. ZTO films were deposited by RF/DC hybrid magnetron co-sputtering using ZnO (RF) target and $SnO_2$ (DC) targets, and then GZO films were deposited by DC magnetron sputtering using an GZO ($Ga_2O_3$:5.57 wt%) target. These films were post-annealed at temperature of 200, $300^{\circ}C$ in air and vacuum ambient for 30 min. In the case of post-annealing in air, ZTO/GZO double layer showed relatively low resistivity change, compared to GZO single layer. Furthermore, ZTO/GZO double layer revealed low WVTR, compared to GZO single layer. Therefore, it can be confirmed that ZTO film doing a role with barrier for water or oxygen diffusion.

• Bulletin of the Korean Chemical Society
• /
• 제21권7호
• /
• pp.715-719
• /
• 2000

A ceramic powder of destructive adsorbent was synthesized by impregnating copper and manganese on the surface of silica aerosil@. In-site FTIR measurements on pulses of malodorant tert-butylmercaptan injected over the powder showed that rert-butylmercaptan dimerized into di-tert-hutyldisulfide on the surface of the adsorbent in an ambient condition. GC/MS measurement on the gas over the adsorbent showed no tert-butylmercaptan remaining, and showed only the dimerization product of di-tert-butyldisulfide. Most of the dimerization product, di-tert-butyldisulfide,remained on the surface of the adsorbent as physisorbed condense, and apparently Iowered the destruction efficiency by blocking the surface from the access by tert-butylmercaptan. Upon being heated above $100^{\circ}C$ it was observed that the physisorbed di-tert-butyldisulfide dissociated back into tert-butylmercaptan. tert-butylmercaptan physisorbed on the activated carbon, thereby no dimerization was occurring on the surface of the activated carbon. In an argn environment, the dimerization reaction was practically not occurring even on the surface of the adsorbent, indicating the free oxygen in air was also participating in the dimerization reaction. Water was identified as a by-product of the dimerization reaction. Possible reactions on the surface of the adsorbent were proposed.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제23회 추계학술대회 논문집
• /
• pp.178-183
• /
• 2004

액체산소 탱크 내에서의 열적 성층화(thermal stratification) 현상은 대기로부터의 열 투입과 탱크 내에서의 극저온 액체의 열적 비평형에 의해 발생된다. 열적 성층화 현상은 벤트 시스템, 탱크 단열. 펌프 설계에 영향을 미치게 되므로 정교한 해석 및 시험적 검증이 필요하다. 본 논문에서는 side-wall에서의 열 투입에 의해 발생되는 경계층 유동을 해석적 방법으로 1차원 모델링하여 시간에 따른 성충화 부피의 증가 및 탱크 내에서의 높이에 따른 온도 분포를 묘사한다.

• 한국재료학회지
• /
• 제30권12호
• /
• pp.687-692
• /
• 2020

A zinc-air battery consists of a zinc anode, an air cathode, an electrolyte, and a separator. The active material of the positive electrode is oxygen contained in the ambient air. Therefore, zinc-air batteries have an open cell configuration. The external condition is one of the main factors for zinc-air batteries. One of the most important external conditions is temperature. To confirm the effect of temperature on the electrochemical properties of zinc-air batteries, we perform various analyses under different temperatures. Under 60 ℃ condition, the zinc-air cell shows an 84.98 % self-discharge rate. In addition, high corrosion rate and electrolyte evaporation rate are achieved at 60 ℃. Among the cells stored at various temperature conditions, the cell stored at 50 ℃ delivers the highest discharge capacity; it also shows the highest self-discharge rate (65.33 %). On the other hand, the cell stored at 30 ℃ shows only 2.28 % self-discharge rate.

• Bulletin of the Korean Chemical Society
• /
• 제9권5호
• /
• pp.289-291
• /
• 1988

The ratio of trivalent to divalent copper has been determined by the redox titration for two superconducting phases of $YBa_2Cu^{3+}_{2x}Cu^{2+}_{3-2x}O_{6.5+x}$ with the onset temp. of 60K (x = 0.23 ${\pm}$ 0.01) and 90K (x = 0.35 ${\pm}$ 0.02), and for the insulating one (x ${\cong}$ 0) which was kept in an ambient atmosphere for 72 hrs. It is found that $T_c$, and the ratio of $Cu^{3+}/Cu^{2+}$ depend strongly on the annealing temperature and time. A typical orthorhombic phase can easily be obtained by a slow cooling or stepwise cooling at $PO_2$ = 1 atm, and shows a high Tc (ca. 90K) superconductivity.

• 한국초전도ㆍ저온공학회논문지
• /
• 제9권1호
• /
• pp.14-17
• /
• 2007

The slot-die coating & calcination process was adopted to fabricate the long YBCO precursor films on the buffered metal tape for the $2^{nd}$ generation coated conductors. To obtain the smooth and crack-free surface of long YBCO precursor films, the parameters of slot-die coating and the process variables of calcination step must be optimized simultaneously in reel-to-reel method. Among the parameter of slot-die coating process, the viscosities of the precursor solution was controlled from 60cP to 200cP to obtain the thicker films from on single coating. The slot-die gap, the injection rate of precursor solution, the moving speed of buffered metal tape etc. are controlled lot the full coverage and smooth surface of YBCO precursor films. The slot-die coated films are moved through the tube furnace with predetermined heating profiles in humid oxygen ambient The YBCO precursor films was identifed with $Y_2O_3,\;BaF_2$, and CuO phase by XRD and consisted of fine grains of about 20nm size observed by FE-SEM. The YBCO films show the critical current density over $MA/cm^2$ using the precursor films formed by the continuous slot-die coating & calcination process.

• 한국초전도ㆍ저온공학회논문지
• /
• 제11권1호
• /
• pp.5-8
• /
• 2009

MgO nanodots have been deposited and formed on top of the substrate surface. Mg was sputtered to form the MgO nanodots on the single crystal substrates by rf-sputtering method and followed by heat treatment in the oxygen ambient. The deposition and formation of MgO nanodots have been controlled systematically using the process variables such as substrate temperature, sputtering time, and rf-power. As the substrate temperature increased from the room temperature the density of MgO nanodots decreased. The optimal conditions of MgO nanodots formation using the rf-sputtering was investigated and the maximum density of more than $230/{\mu}m^2$ on single crystal substrates was obtained when the rf-power of 100 watts was applied for 30 seconds at room temperature. The typical size of MgO nanodots was identified to be <160 nm(diameter) and 4-30nm (height) by atomic force microscopy. The modulated surface morphology was examined through surface images and cross-section analysis and discussed for the artificial pinning sites in the superconducting films.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4159-4169
• /
• 2022

Hydrogen mitigation using Passive Autocatalytic Recombiners (PARs) has been widely accepted methodology inside reactor containment of accident struck Nuclear Power Plants. They reduce hydrogen concentration inside reactor containment by recombining it with oxygen from containment air on catalyst surfaces at ambient temperatures. Exothermic heat of reaction drives the product steam upwards, establishing natural convection around PAR, thus invoking homogenisation inside containment. CFD models resolving individual catalyst plate channels of PAR provide good insight about temperature and hydrogen recombination. But very thin catalyst plates compared to large dimensions of the enclosures involved result in intensive calculations. Hence, empirical correlations specific to PARs being modelled are often used in integral containment studies. In this work, an experimentally validated CFD model of PAR has been employed for developing an empirical correlation for Indian PAR. For this purpose, detailed parametric study involving different gas mixture variables at PAR inlet has been performed. For each case, respective values of gas mixture variables at recombiner outlet have been tabulated. The obtained data matrix has then been processed using regression analysis to obtain a set of correlations between inlet and outlet variables. The empirical correlation thus developed, can be easily plugged into commercially available CFD software.

• Corrosion Science and Technology
• /
• 제23권1호
• /
• pp.33-40
• /
• 2024

The concentration and diffusion coefficient of oxide ion vacancies in the oxide scale formed on Fe-22Cr-0.5Mn ferritic stainless steel with and without molybdenum (Mo) was measured at 800℃ by the electrochemical polarization method. After pre-oxidation for 100 h in ambient air at 800 ℃, the oxide scale on one side was completely removed with sandpaper. A YSZ plate was placed on the side where the oxide scale remained. Platinum (Pt) meshes were attached on the top of the YSZ plate and the side where the oxide scale was removed. Changes in electrical current were measured after applying an electrical potential through Pt wires welded to the Pt meshes. The results were interpreted by solving the diffusion equation. The diffusion coefficient and concentration of oxide ion vacancy decreased by 30% and 70% in the specimen with Mo, respectively, compared to the specimen without Mo. The oxide ion vacancy concentration of chromia decreased due to the addition of Mo.