• 한국레이저가공학회지
• /
• 제3권1호
• /
• pp.38-45
• /
• 2000

A 4㎾ RS840 CO2 laser with a powder auto-feeding apparatus has been used to deposit multiple overlapping tracks of Ni-base superalloy on to low carbon steel. It was found that the surface roughness(turbulence) of an overlapped cladding layer decreased with the increase of the overlapping ratio in an oscillating manner. When the overlapping ratio had values of 0.62, the surface turbulence was lowest. Overlapping ratio offer significant potential for improvement of materials surface properties such as corrosion performance and wear resistance. This paper reports that the overlapping ratio shows best corrosion resistance. The tensile residual stresses generated at the higher overlapping ratio( ＞ 0.45) and the element concentration of Fe increased in the surface layer at the lower overlapping ratio( ＜ 0.45) may lead to worse corrosion resistance.

• Journal of electromagnetic engineering and science
• /
• 제2권1호
• /
• pp.1-4
• /
• 2002

Performance improvement of the DS-CDMA system by the spectrum-overlap is important for better service quality or more system capacity. In this paper, an analysis thor capacity improvement is newly considered when the Lanczos chip waveform is used for the spectrum-overlapped DS-CDMA system. RC(relative capacity) is the ratio of the capacity of overlapping system to that of non-overlapping system, which is used for the expression of the capacity improvement. The optimal overlapping ratio is numerically found to make the maximum capacity improvement When the rectangular chip waveform is used far the overlapping system, maximum capacity improvement is increased by about 10% at the required BER=$10^{-3}$TEX> and the optimal overlapping ratio is 1.23. When the 95 % power bandwidth is considered for the Lanczos chip waveform, maximum capacity improvement is increased by 34.4% at overlapping ratio of 1.55 when the required BER is $10^{-3}$TEX>. The lower required BER far the better communication quality makes gradually smaller capacity improvement.

• 한국터널지하공간학회 논문집
• /
• 제23권3호
• /
• pp.167-181
• /
• 2021

터널굴착의 경제성 확보 및 굴착 시 발생하는 진동저감을 위해 워터젯 시스템을 활용한 새로운 형태의 암반 굴착공법이 개발되고 있다. 워터젯 절삭을 이용한 효율적인 암반 굴착을 위해서는 워터젯 절삭폭의 중첩과정이 필수적이다. 본 연구는 초고압 연마재 워터젯 시스템을 이용하여 절삭폭 중첩도 및 이격거리에 따른 화강암 시편 절삭실험을 수행하였다. 실험결과를 바탕으로 중첩도 단계에 따른 화강암 절삭성능을 분석하였다. 그리고 형상인자를 절삭깊이, 절삭폭, 그리고 절삭부피로 분류하여 중첩 절삭 후 단면의 형상을 분석하였다. 절삭폭 중첩도가 58% 이하가 되면 중첩이 충분하지 않아 연속적인 암반제거가 불가능하였다. 반면 절삭폭 중첩도 67% 이상에서는 과절삭 현상이 확인되었다. 한편 부분중첩(25~75%) 조건에서는 기존 워터젯 절삭에 비해 효율적인 부피제거가 가능한 것으로 분석되었다. 해당 연구는 워터젯을 활용한 암반 굴착 시 최적 중첩도를 결정하기 위한 중요한 기초자료로 활용될 수 있을 것으로 기대된다.

• 방송공학회논문지
• /
• 제21권5호
• /
• pp.816-823
• /
• 2016

본 논문은 디스플레이 휘도를 증가시키기 위하여 적색, 녹색, 청색 고휘도 Light Emitting Diode(LED)를 광원으로 사용하고, Digital Micro Device(DMD) 패널을 적용한 헤드업 디스플레이에서 세 개의 LED 광원 합성 비율과 합성에 따른 양자화 노이즈를 최소화시키는 LED 합성 비율을 연구하였고, 밝기에 영향을 미치는 녹색 LED 구동 비율과 접합 온도에 대하여 분석하였다. 이를 통하여 39%의 LED 중첩 방법을 통하여 황색과 청록색의 2차원 색을 합성하여 33.3%의 휘도 증대 효과를 얻을 수 있었다. 또한 양자화노이즈를 억제하고 영상 화질 측면에서 우수한 색정밀도를 얻을 수 있었다.

• Journal of information and communication convergence engineering
• /
• 제13권3호
• /
• pp.215-219
• /
• 2015

Cells in a culture process transform with time and produce many overlapping cells in their vicinity. We are interested in a separation algorithm for images of overlapping cells taken using a fluorescence optical microscope system during a cell culture process. In this study, all cells are assumed to have an ellipse-like shape. For an ellipse fitting-based method, an improved least squares method is used by decomposing the design matrix into quadratic and linear parts for the separation of overlapping cells. Through various experiments, the improved least squares method (numerically stable direct least squares fitting [NSDLSF]) is compared with the conventional least squares method (direct least squares fitting [DLSF]). The results reveal that NSDLSF has a successful separation ratio with an average accuracy of 95% for two overlapping cells, an average accuracy of 91% for three overlapping cells, and about 82% accuracy for four overlapping cells.

• 소성∙가공
• /
• 제17권3호
• /
• pp.203-209
• /
• 2008

In this paper, experimental investigation has been performed to analyze the forming process of toothed or serrated sheets, which is used as strap engaging surface of the seal to secure together overlapping portions of steel or plastic strapping ligature. Serration formed on the strap engaging surface of the seal prevent from relative slipping between overlapping ligatures after closing the seal. The geometry of tooth on the strap engaging surface is directly related to the quality of securing overlapping ligatures together. Inclined indentation followed by scratching operation has been proposed and applied to the experiments. Punch entry and face angles are selected as process variables to see the influence of these variables on the tooth geometry. Five different punch entry angles have been applied to experiments and three different punch face angles have been selected for each case of punch entry angle. Clay is selected as model material for experiments. Experimental results are summarized in terms of tooth height, tooth width, and aspect ratio such as tooth height to width ratio, respectively.

• 소성∙가공
• /
• 제20권8호
• /
• pp.575-580
• /
• 2011

Direct laser melting(DLM) is promising as a joining method for producing parts for automobiles, aerospace, marine and medical applications. An advantageous characteristic of DLM is that it affects the parent metal very little. The mechanical properties of parts made by DLM are strongly affected by the porosity and surface roughness of the laser melted beads. This is a systematic study of the effects of the porosity and surface roughness of laser melted beads using various processing parameters, such as laser power, scan rate and overlapping ratio of the fill spacing. The specimens were fabricated with 316L and 304L austenitic stainless steel powder. Dense parts with low porosity were obtained at low laser scan speed, as it increased the aspect ratio of the parental material and the depth of penetration. The variations of surface roughness were examined at various processing parameters such as overlapping ratio and laser power.

• Journal of electromagnetic engineering and science
• /
• 제1권2호
• /
• pp.120-125
• /
• 2001

The capacity improvement in the DS-CDMA system can be obtained by allowing spectrum-overlap between adjacent channels. In this paper, an analysis for capacity improvement is newly considered according to the various chip waveforms in the partial spectrum-overlapped DS-CDMA system. Optimum-overlapping ratio is numerically found to obtain maximum capacity improvement for each chip waveform. Assuming the bandwidth containing 95% of the total power, i.e., 95% power bandwidth, rectangular chip waveform has the largest capacity improvement in the considered chip waveforms and then the amount of improvement is 136.5% at overlapping ratio 1.5 for BER = $10^{-3}$TEX> . Furthermore, as the required BER becomes lower, the capacity improvement gets smaller for a1l of chip waveforms. For the unequal power channels, it is shown that the larger capacity improvement is achieved as the power of desired channel becomes larger than that of adjacent channels. And the capacity improvement can be obtained even though the desired channel power is lower than the adjacent channel power.

• 말소리와 음성과학
• /
• 제2권2호
• /
• pp.63-68
• /
• 2010

A new version of sequential probability ratio test (SPRT) which has been investigated in utterance-length control is proposed to obtain uniform response results in speaker verification (SV). Although SPRTs can obtain fast responses in SV tests, differences in the performance may occur depending on the compositions of consonants and vowels in the sentences used. In this paper, a fast sequential probability ratio test (FSPRT) method that shows consistent performances at all times regardless of the compositions of vocalized sentences for SV will be proposed. In generating frames, the FSPRT will first conduct SV test processes with only generated frames without any overlapping and if the results do not satisfy discrimination criteria, the FSPRT will sequentially use frames applied with overlapping. With the progress of processes as such, the test will not be affected by the compositions of sentences for SV and thus fast response outcomes and even consistent performances can be obtained. Experimental results show that the FSPRT has better performance to the SPRT method while requiring less complexity with equal error rates (EER).

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2000년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.131-134
• /
• 2000