• Journal of the Korean Chemical Society
• /
• v.57 no.1
• /
• pp.35-39
• /
• 2013

The chemical bonding and elastic properties of $Ti_2AC$ (A = Ga, Tl) have been investigated by means of extended H$\ddot{u}$ckel tight-binding band structure calculations. The bulk modulus of $Ti_2AC$ decreases as Ga is replaced with Tl at the A sites. This can be understood by considering the relative strength of Ti-A bonds resulting from the different atomic size of 3A-group elements. The analysis of the projected density of states (PDOS) and the crystal orbital overlap population (COOP) for the respective phases shows that Ti-Ga bonds in $Ti_2GaC$ are stronger than Ti-Tl bonds in $Ti_2TlC$.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.2
• /
• pp.161-167
• /
• 1989

The results of ab initio(MP2/6-31G) molecular orbital calculations of the dipole moment derivatives and gas phase IR intensities in chloromethanes are reported. The theoretical polar tensors are analyzed into the net charge, charge-flux, and overlap contributions. The charge-flux contribution was found to be dominant in the Cl atom polar tensor, while the net charge effect was the most prominent contribution for the H atom polar tensor. The Cl atom polar tensor appeared, in a good approximation, to be transferable among various chloro molecules. On the other hand, for the prediction of IR spectra of complex hydrocarbons containing chlorine atoms, some empirical adjustment of the H-atom polar tensor seemed to be made depending on the number of Cl atoms bound to the certain carbon atom.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.3
• /
• pp.263-272
• /
• 1998

This paper presents the new control strategy that can minimizes the torque ripple by considering the magnetic nonlinearity and phase torque averlapping intervals, and describes the whole SRM drive system using proposed control method implemented by DSP(Digital Signal Processor). To do this, inductance and torque are, at first, measured according to the variation of rotor position angle while current is kept constant at predetermined several values. From these measured values, the entire inductance and torque for any current and rotor position are inferred by using neural network. And the waveform of the reference phase torque is determined for the torque ripple to be minimized considering the torque overlap between phases. The controller is designed for the actual torque obtained by the inferred torque look-up table using measured current and rotor position angle to track the predetermined reference phase torque by delta modulation technique. To perform a real time processing and ensure the reliability of the controller, DSP is implemented.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.1
• /
• pp.33-40
• /
• 2008

This paper proposes a sensorless drive method that estimates the rotor position by analysing Back EMF of single-phase Switched Reluctance motor (SRM). The rotor position information is necessary required, because SRM's torque is generated by exciting a stator winding according to rotor position. In order to detect the position of the rotor, the various rotor position sensors have been used. However, most of the position sensors not only increase the construction cost and the volume of the motor but also decrease reliability of driving system with environment. This paper proposed the method using the Back EMF to solve such problems. When a rotor and stator are overlapped, the Back EMF is sharply changed. By detecting this point, the rotor position can be estimated. Thus SRM is driven by turn on and turn off switches at the proper position through speed calculation. The validity of proposed method is verified through simulation and experiment.

• Journal of Welding and Joining
• /
• v.33 no.5
• /
• pp.53-60
• /
• 2015

Laser surface Melting Process is getting hardening layer that has enough depth of hardening layer as well as no defects by melting surface of substrate. This study used CW(Continuous Wave) Yb:YAG and STD11. Laser beam speed, power and beam interval are fixed at 70mm/sec, 2.8kW and 800um respectively. Hardness in the weld zone are equal to 400Hv regardless of melting zone, remelting zone overlapped by next beam and HAZ. Similarly, microstructures in all weld zone consist of dendrite structure that arm spacing is $3{\sim}4{\mu}m$, matrix is ${\gamma}$(Austenite) and dendrite boundary consists of ${\gamma}$ and $M_7C_3$ of eutectic phase. This microstructure crystallizes from liquid to ${\gamma}$ of primary crystal and residual liquid forms ${\gamma}$ and $M_7C_3$ of eutectic phase by eutectic reaction at $1266^{\circ}C$. After solidification is complete, primary crystal and eutectic phase remain at room temperature without phase transformation by quenching. On the other hand, microstructures of substrate consist of ferrite, fine $M_{23}C_6$ and coarse $M_7C_3$ that have 210Hv. Microstructures in the HAZ consist of fine $M_{23}C_6$ and coarse $M_7C_3$ like substrate. But, $M_{23}C_6$ increases and matrix was changed from ferrite to bainite that has hardness above 400Hv. Partial Melted Zone is formed between melting zone and HAZ. Partial Melted Zone near the melting zone consists of ${\gamma}$, $M_7C_3$ and martensite and Partial Melted Zone near the HAZ consists of eutectic phase around ${\gamma}$ and $M_7C_3$. Hardness is maximum 557Hv in the partial melted zone.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.531-540
• /
• 2019

Spectral Amplitude Coding Optical Code Division Multiple Access (SAC OCDMA) is an advanced technique in asynchronous environments. This paper proposes design and implementation of a novel quantum logic gate (QLG) code, with code construction algorithm generated without following any code mapping procedures for SAC system. The proposed code has a unitary matrices property with maximum overlap of one chip for various clients and no overlaps in spectra for the rest of the subscribers. Results indicate that a single algorithm produces the same length increment for codes with weight greater than two and follows the same signal to noise ratio (SNR) and bit error rate (BER) calculations for a higher number of users. This paper further examines the performance of a QLG code based SAC-OCDMA system with NAND and direct detection techniques. BER analysis was carried out for the proposed code and results were compared with existing MDW, RD and GMP codes. We demonstrate that the QLG code based system performs better in terms of cardinality, which is followed by improved BER. Numerical analysis reveals that for error free transmission (10^-9), the suggested code supports approximately 170 users with code weight 4. Our results also conclude that the proposed code provides improvement in the code construction, cross-correlation and minimization of noises.

• Korean Journal of Materials Research
• /
• v.17 no.11
• /
• pp.580-586
• /
• 2007

To enhance the reliability of a newly designed reciprocating compressor applied in a domestic compressor, accelerated life tests were developed using new definitions of the sample size and the $B_1$ life index. In $1^{st}$ accelerated life testing, the compressor was locked due to the fracture of the suction reed valve. The failure modes and mechanisms of the suction reed valve in the accelerated tests were found to be similar to that of the failed product in the field. The root cause of the failure was the overlap between the suction reed valve and the valve plate in the suction port. The missing parameters in the design phase were modified by expanding the trespan size, introducing tumbling process, changing the material and thickness for the valve, introducing a ball peening and brushing process for the valve plate. In $2^{nd}$ accelerated life testing, the compressor was locked due to the interference between the crank shaft and thrust washer. The corrective plan was to heat treat the crank shaft. The $B_1$ life of the compressor improved from 1.5 to 12.9 years.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.15 no.7
• /
• pp.870-874
• /
• 2005

This paper presents capacitive tactile sensor that can detect normal and shear forces. This tactile sensor consists of index plate, sensing plate, and elastic dielectric layer. The calculated sensing character is based on the changes of space between two horizontal plate. Larger overlap areas and narrow space between top and bottom plate guarantees higher sensitivity. Tactile sense information can be calculated from the changes of phase of output signal. The symmetric arrangement of sensing plates makes the manufacturing process easier and guarantees the stability of the structure. In this paper, the sensor structure is designed, the mechanism of the Proposed sensor is theoretically explained, and the simulated result is presented.

• Sleep Medicine and Psychophysiology
• /
• v.18 no.2
• /
• pp.63-66
• /
• 2011

It has been controversial whether upper airway resistance syndrome (UARS) is a distinct syndrome or not since it was reported in 1993. The International Classification of Sleep Disorders classified UARS under obstructive sleep apnea syndrome (OSAS) in 2005. UARS can be diagnosed when the apnea-hypopnea index (AHI) is fewer than 5 events per hour, the simultaneously calculated respiratory disturbance index (RDI) is more than 5 events per hour due to abnormal non-apneic non-hypopneic respiratory events accompanying respiratory effort related arousals (RERAs), and oxygen saturation is greater than 92% at termination of an abnormal breathing event. Although esophageal pressure measurement remains the gold standard for detecting subtle breathing abnormality other than hypopnea and apnea, nasal pressure transducer has been most commonly used. RERAs include phase A2 of cyclical alternating patterns (CAPs) associated with EEG changes. Symptoms of OSAS can overlap with UARS, but chronic insomnia tends to be more common in UARS than in OSAS and clinical symptoms similar with functional somatic syndrome are also more common in UARS. In this journal, diagnostic and clinical differences between UARS and OSAS are reviewed.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.803-804
• /
• 2006

우리는 이전 논문을 통해 Air blower용 모터에서 널리 사용되고 있는 단상 유도기를 기존의 분포 권선 방식에서 벗어나 집중 권선 방식을 사용하여 설계한 결과 생산 공정의 단계를 줄이고 많은 생산 비용을 줄일 수 있었다. 또한 집중 권선형에서 발생할 수 있는 고조파 문제를 로터의 skew와 overlap 권선 방식을 이용하여 해결 할 수 있음을 증명하였다. 그러나 이러한 이점에도 불구하고 시제품의 특성을 측정한 결과 집중 권선형 모터의 자계 불균형 때문에 기존 분포권 모터에 비해 소음과 진동 특성이 좋지 않은 결과를 보였다. 이에 본 논문에서는 소음과 진동 특성을 고려하여 기존의 기동 및 정격 토크 특성을 유지하면서 토크 리플을 저감할 수 있는 방법을 로터의 Skew 각도 영향, 권선 사양 및 스테이터 및 로터 형상 등을 고려하여 새롭게 설계하였고 그 결과를 제시하였다.