• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 A
• /
• pp.450-451
• /
• 2006

The method of conductor wiring is that a messenger wire is installed, the end of the wire is connected to the conductor and a engine puller pulls the conductor. The length of one section of wiring is $3{\sim}5km$ and one group messenger wire pulls simultaneously $2{\sim}4$ group conductor, while a tensioner maintains wiring tension to prevent the deflection of the conductor. However, there are many obstacles such as roads, power lines, communication lines, buildings, farms and crops. Therefore to prevent damage from conductor deflection a staging is used. The currently used staging is scaffolding lumber which is difficult to secure and it's construction efficiency is very low because it requires a lot of time and manpower. So this study developed a insulating defense tube and pipe connecting device, and a truss structure fabrication module using steel pipe which reduces construction time and cost through a compressive and dielectric strength test.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제3C권5호
• /
• pp.165-170
• /
• 2003

This paper presents development of solid core suspension disc insulators (cap and cap suspension disc insulator) for replacing cap and pin suspension disc insulators in overhead transmission and distribution lines which expose to lightning discharges. By this means the punctured problem caused by steep front surge voltage created by lightning discharge on the lines can be solved. The solid core suspension insulator was designed and constructed based on the dimensions of conventional suspension disc insulators (cap and pin insulators). The insulators are made of alumina porcelain. The electrical and mechanical characteristics of the solid core suspension insulators were carried out. The puncture test was performed in the air by applying steep front impulse voltage with amplitude about 2.5 per unit of 50% flashover (CFO) of the insulator unit at negative standard lightning impulse $1.2/50\;\mu\textrm{s}$ with steepness up to $9200\;kV/\mu\textrm{s}$. The testing results show that solid core suspension disc insulators are not punctured eventhough the steepness of the steep front impulse voltage was increased up to $9200\;kV/\mu\textrm{s}$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.171-172
• /
• 2008

이 논문은 2회선 가공송전선의 1회선 고장시에 선로 운전의 안전성을 확보하기 위한 단시간 과도정격을 결정하기 위한 방법에 대하여 기술한다. 먼저 선로의 단시간 과도정격 산정에 영향을 미치는 주요 요소들인 도체의 수명, 접속개소의 안정성, 선로의 지상고 및 이격거리에 대하여 살펴본 후, 이를 바탕으로 국내 상황에 적합한 과도정격 운영방안을 제시한다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.2094-2095
• /
• 2008

In order to protect conductors from oscillations or vibrations due to winds, spacer dampers or spacers are installed on bundled conductors in overhead transmission lines. Generally the spacer damper clamp can move slightly according to oscillation directions, namely conductor direction, vertical & horizontal direction This is for reducing fatigue phenomena of the clamps. Sometimes movement of the clamp to conductor direction raises a doubt for its necessity. Then this paper carried out oscillation tests to know clamp displacement due to the subspan oscillation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.1539-1540
• /
• 2015

본 연구는 가공 활선 송전선로의 이상 진단을 위한 시스템 개발에 관한 것으로 송전 철탑 경간내에 설치되어 있는 송전선을 주행하며 전선의 내부 또는 외부의 열화를 확인하기 위한 것이다. 본 연구에 의한 시스템은 지상으로부터 30m 이상의 높이에서 설치되어 운행되기 때문에 바람에 의해 낙하되지 않도록 구성하였다. 또한 복도체 또는 4도체 선로를 주행하도록 설계하였으며 345kV 고압에서도 전계 및 자계의 영향을 받지 않도록 설계하였다. 전선의 이상 검지를 위해서 카메라를 설치하여 얻어진 데이터를 영상 처리 하여 이상 부위에 대한 에너지 변화를 관찰하여 이상 유무를 판단하도록 하였다. 완성된 시스템은 설치 및 이동을 위해서 경량화 시켰으며 분해 조립이 쉽도록 구성하였다. 본 시스템의 현장 적용에 의한 실험 결과 1m/sec의 이동 속도에서 1mm 이하의 스크래치에 대하여 검출이 가능하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 A
• /
• pp.205-207
• /
• 2003

The line impedance is important data that is applied in all analysis fields of electric power system like power flow, fault current, stability and relay calculation etc. Usually, impedance can be accurately calculated in case of overhead line. However, in case of power cables or combined transmission lines, impedance can not be accurately calculated because cable systems have the sheath, grounding wires, and earth resistance. Therefore, if there is a fault in cable system, these terms will severely be caused much error to calculation of impedance. Therefore, the line impedance were measured for this study in an actual power system of underground cables, and were analyzed by a generalized circuit analysis program EMTP for comparison with the measured value. These analysis result is considered to become foundation of impedance calculation for underground cable.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2007년도 하계종합학술대회 논문집
• /
• pp.291-292
• /
• 2007

Porcelain insulators are widely used in overhead high-voltage power transmission lines while providing adequate insulation to withstand switching and lightning over voltages. For the safety consideration, we proposed a novel insulator inspection method using harmonic, which is retrieved from the low frequency signal. The working principle of this new method is based on the relationship between the low frequency harmonic and the defective characteristic of the insulators. So, in this paper, the harmonic retrieval in the complex noise is solved with the HOC (High Order Cumulants) is extended. In the experiment, as one of our dedicated contribution, we illustrate low frequency harmonic and the defective characteristics of the porcelain insulators.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전력기술부문
• /
• pp.396-399
• /
• 2003

최근 전력산업의 구조개편, 선로건설의 어려움, 송전선로의 노후화, 선로용량 취약개소의 상시감시 필요성 등으로 인하여 선로의 허용 전류용량을 합리적으로 평가하는 한편, 도체의 허용전류를 실시간으로 산정하여 현재 운용상태와 비교하여 그 한계 및 여유 정도를 알아보는 것이 중요한 문제로 대두되었다. 본 논문에서는 이러한 연구의 일환으로 먼저 기상모델을 중심으로 실시간 허용전류 산정 알고리즘에 대하여 살펴보고, 대전 지역의 가공 송전선로를 대상으로 선로 주변의 기온, 풍속, 지형 정보를 이용하여 동적으로 허용전류를 산정하여 그 이용 가능성을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.612-613
• /
• 2007

The line impedance is important data that are applied in all analysis fields of electric power system such as power flow, fault current, stability and relay calculation etc. Usually, the impedance can be accurately calculated in case of overhead line. However, in case of power cables or combined transmission lines, the impedance can not be accurately calculated because cable systems have the sheath, grounding wires, and earth resistances. Therefore, if there is a fault in cable system, these terms will severely be caused many errors for calculating impedance. In this paper, the line impedance is measured in a power system of underground cables, and is analyzed by a generalized circuit analysis program, EMTP(Electromagnetic Transient Program), for comparison with the measured value. These analysis results are considered to become foundation of impedance calculation for underground cables.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.407_408
• /
• 2009

Generally, the deterioration characteristics of a conductor affected by a forest fire can be analyzed through simulation of a forest fire and results of the simulation. However, there are little accomplishments of that kind of simulation applied to the power transmission, and there aren't actual analysis for a sample exposed in a forest fire. This paper deals with the experimental results that apply to a new wire by an artificial flame equipment because it's difficult to directly analyze the characteristic by a forest fire. Also, after an artificial flame is applied to a normal ACSR for various experimental conditions, changes of mechanical and material characteristics of the ACSR were analyzed by the surface inspection and load-tests of tensile of the ACSR. Then, the database will be made to made to predict the state of deteriorated wires by a forest fire using those two data, and data necessary to diagnose the life state of an ACSR wire affected by a forest fire will be given.