• 대한건축학회논문집:구조계
• /
• 제34권7호
• /
• pp.19-26
• /
• 2018

This study tested 25 lightweight aggregate concrete (LWAC) mixtures using the expanded bottom ash and dredged soil granules to examine the compressive strength gain of such concrete with different ages. The test parameters investigated were water-to-cement ratios and the natural sand content for the replacement of lightweight fine aggregate. The compressive strength gain rate in the basic equation specified in fib model code was experimentally determined in each mixture and then empirically formulated as a function of the water-to-cement ratio and oven-dried density of concrete. When compared with 28-day compressive strength, the tested LWAC mixtures exhibited relatively low gain ratios (0.49~0.82) at an age of 3 days whereas the gain ratios (1.16~1.41) at 91 days were higher than that (1.05~1.15) of the conventional normal-weight concrete. Thus, the fib model equations tend to overestimate the early strength gain of LWAC but underestimate the long-term strength gain. The proposed equations are in good agreement with the measured compressive strength development of LWAC at different ages, indicating that the mean and standard deviation of the normalized root mean square errors determined in each mixture are 0.101 and 0.053, respectively.

• Journal of Forest and Environmental Science
• /
• 제26권2호
• /
• pp.131-136
• /
• 2010

In an effort to evaluate the qualities of the unused woods designed for art materials, Yellow pine, Pitch pine, Suwon poplar, Platanus and Cherry grown in Korea has been investigated in the study. Physical and mechanical properties such as density, hardness, roughness, and abrasion of the woods were examined. Among the five species, Cherry wood showed the highest density in green, air-dried and oven-dried conditions. Hardness of Cherry wood was higher than those of Suwon poplar and Platanus. In softwoods, Pitch pine showed greater hardness than Yellow pine. Yellow pine and Platanus had the highest values of wood surface roughness. Abrasion value of cross, radial and tangential sections was the highest in Yellow pine and Suwon poplar. It has been concluded from the experiment that physical and mechanical properties such as density, hardness, roughness, and abrasion of the woods can be used as an indicator of the suitability for woodcraft material.

• 대한화장품학회지
• /
• 제38권2호
• /
• pp.133-138
• /
• 2012

본 연구는 건조된 코아세르베이트 필름의 물리적 특성이 샴푸 건조 후 모발 사용감에 미치는 상관관계를 조사하기 위하여 실시하였다. 단순 샴푸 조성물은 동일한 조성의 계면활성제에 양이온 전하 밀도가 서로 다른 두 종류의 양이온 폴리머를 사용하여 제조하였다. 이 단순 조성물을 물에 희석하여 코아세르베이트(Coacervate)를 형성되도록 하였고, 3000 rpm, 30 min 조건으로 원심 분리하여 형성된 코아세르베이트를 얻었다. 얻어진 코아세르베이트를 유리판 위에 균일한 두께로 도포하고 $50^{\circ}C$ 건조기에서 1 h 건조하여 코아세르베이트 필름을 얻었다. 이렇게 얻어진 코아세르베이트 필름의 접촉각과 코아세르베이트의 SEM 이미지 조사를 수행하였고, 코아세르베이트의 수분 보유량과 수분 유지력을 동시에 조사하였다. 샴푸 후 건조된 모발의 부드러움과 보습감은 모발타래를 이용하여 전문 미용 패널이 평가를 수행하였다. 본 실험결과 건조된 코아세르베이트 필름의 특성이 샴푸 후 건조된 모발의 부드러움 및 보습감에 영향을 주는 것으로 확인되었다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.71-74
• /
• 2005

In this paper, the effects of the MWCNTs on the PTC characteristics of the conventional CB/polymer nanocomposites were investigated. For the uniform dispersion of the MWCNTs in the polymer matrix., nitricacid-treated MWCNTs were dispersed with the dissolved HOPE in the solvent. After evaporating solvent, the dried master batches in the oven were melt blended mixed with CB and HDPE to obtain the PTC materials. The initial resistivity of PTC materials decreased and the PTC intensity increased with the MWCNTs. During three repeated heating and cooling cycles, the PTC materials containing MWCNTs showed a great reproducibility due to the conductive network structures of CB particles and MWCNTs.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.148-148
• /
• 2017

Surface modification is a type of mechanical manipulation skills to achieve extensive aims including corrosion control, exterior appearance, abrasion resistance, electrical insulation and electrical conductivity of substrate materials by generating a protective surface using electrical, physical and chemical treatment on the surface of parts made from metallic materials. Such surface modification includes plating, anodizing, chemical conversion treatment, painting, lining, coating and surface hardening; this study conducted cavitation experiment to assess improvement of durability using anodizing. In order to observe surface characteristics with applied current density, the electrolyte temperature, concentration was maintained at constant condition. To prevent hindrance of stable growth of oxide layer due to local temperature increase during the experiment, stirring was maintained at constant speed. In addition, using galvanostatic method, it was maintained at processing time of 40minutes for 10 to $30mA/cm^2$. The cavitation experiment was carried out with an ultra sonic vibratory apparatus using piezo-electric effect with modified ASTM-G32. The peak-to-peak amplitude was $30{\mu}m$ and the distance between the horn tip and specimen was 1mm. The specimen after the experiment was cleaned in an ultrasonic bath, dried in a vacuum oven for more than 24 hours, and weighed with an electric balance. The surface damage morphology was observed with 3D analysis microscope. As a result of the study, differences were observed surface hardness and anti-cavitation characteristics depending on the development of oxide film with the anodizing process time.

• 한국재료학회지
• /
• 제11권10호
• /
• pp.869-878
• /
• 2001

Alumina $(Al_2O_3)$ green bodies were fabricated by gel-casting using three kinds of alumina with different particle size (mean particle size: 4.6 $\mu\textrm{m}$, 0.32 $\mu\textrm{m}$, 10nm). The effects of particle size on gel-casting process and green microstructure were investigated. The optimum dispersion conditions using ammonium salt (D-3019) as dispersant were 0.2 wt% (4.63 $\mu\textrm{m}$), 0.5 wt% (0.32 $\mu\textrm{m}$), and 5.0 wt% (10 nm), in high solid loading. The optimum solid loading of each starting material for gel-casting was obtained as 59 vol% (4.63 $\mu\textrm{m}$), 57 vol% (0.32 $\mu\textrm{m}$), 15 vol% (10 nm), depending on particle size, indicating that nano-size particle (10 nm) represent lower solid loading as high specific surface area than those of other two starting materials. The drying at ambient conditions (humidity; $\thickapprox$90%) was performed more than 48hrs to enable ejection of the part from the mold and then at $120^{\circ}C$ for 2hrs in an air oven, showing no crack and flaw in the dried green bodies. The pore size and distribution of the gelcast green bodies showed the significant decrease with decreasing particle size. Green microstructure was dependent on the pore size and distribution due to the particle size, and on the deairing step. The green density maximum obtained was 58.9% (4.63 $\mu\textrm{m}$), 60% (0.32 $\mu\textrm{m}$), 47% (10 nm) theoretical density (TD), and the deairing step applied before gel-casting did not affect green density.

• 한국수산과학회지
• /
• 제33권6호
• /
• pp.529-532
• /
• 2000

시중 유통김에 대한 세균학적 위생 안전 확보 방안 구축을 위하여, 제품 중의 세균 수를 감소시킬 수 있는 여러 가지 열처리 효과와, 가공 공정 중 외부로부터의 오염이 유입되는 건조 공정 개선시험을 실시한 결과는 다음과 같다. 장기 보관 또는 유통을 목적으로 제품의 수분 감소를 위하여 채택되고 있는 상법의 열처리 (화입) 공정 전후 제품의 세균학적 품질의 차이는 거의 없었다. 마른김을 가스불로 직접 또는 간접 가열할 경우, 제품 중의 세균수는 정도의 차이는 있었지만 최초 균 수 $10^8CFU/g$에서 $10^5CFU/g$로 약 $1{\~}3$ 1og cycle 감소하였다. 조미 열처리 가공 김 가공에 상법적으로 사용되고 있는 배소기를 사용하여 열처리 할 경우 제품 중의 생균수는 $2.2{\times}10^5{\~}5.2{\times}10^7$ CFU/g 에서 $7.0{\times}10^2{\~}5.0{\times}10^5 CFU/g$로 감소하였다. 마른김 표면에 20 W의 자외선을 단면과 양면에 20분간 조사한 경우, 생균수는 $2.2{\times}10^6 CFU/g$에서 $8.0{\times}10^5$ CFU/g and $2.0{\times}10^5$ CFU/g로 각각 감소하였다. 외부 오염을 차단할 수 있는 정치형 건조기를 사용하여 제조한 마른 김의 생균수는 $10^3 CFU/g$로 상업적으로 유통되고 있는 기존의 상품에 비하여 $4{\~}5$ log cycle 정도 낮았다.

• 한국농공학회지
• /
• 제21권2호
• /
• pp.81-103
• /
• 1979

The weathered granite soil involves problems in its stability in soil structures depending upon the reduction of soil strength due to the water absorption, crushability, and content of colored mineral and feldspar. As an attemt to solve the problems associated with soil stability, the crushability of weathered granite soil was investigated by conducting tests such as compaction test, CBR test, unconfined compression test, direct shear test, triaxial compression test, and permeability test on the five soil samples different in weathering and mineral compositions. The experimental results are summarized as follows: The ratio of increasing dry density in the weathered granite soil was high as the compaction energy was low, while it was low as the compaction energy was increased. The unconfined compressive strength. and CBR value were highest in the dry side rather than in the soil with the optimum moisture content, when the soil was compacted by adjusting water content. However, the unconfined compressive strength of smples, which were compacted and oven dried, were highest in the wet side rather than in soil with the optimum moisture content. As the soil becomes coarse grain, the ratio of specific surface area increased due to increased crushability, and the increasing ratio of the specific surface area decreased as the compaction energy was increased. The highest ratio of grain crushability was attained in the wet side rather than in the soil with the optimum moisture content. Such tendency was transforming to the dry side as the compaction energy was increased. The effect of water on the grain crushability of soil was high in the coarse grained soil. The specific surface area of WK soil sample, when compacted under the condition of air dried and under the optimum moisture content, was constant regardless of the compaction energy. When the weathered granite soil and river sand with the same grain size were compacted with low compaction energy, the weathered granite soil with crushability had higher dry density than river sand. However, when the compaction energy reached to certain point over limitation, the river sand had higher dry density than the weathered granite soil. The coefficient of permeability was lowest in the wet side rather than in the optimum moisture content, when the soil was compacted by adjusting soil water content. The reduction of permeability of soil due to the compaction was more apparent in the weathered granite soil than in the river sand. The highly significant correlation coefficient was obtained between the amount of particle breakage and dry density of the compacted soil.

• Journal of the Korean Wood Science and Technology
• /
• 제44권2호
• /
• pp.172-183
• /
• 2016

Densification of the inner part of oil palm trunk (OPT) by the close system compression (CSC) method was performed in this study. The effects of the compression temperature and time on the anatomical, physical and mechanical properties of OPT were evaluated. The inner part of OPT with an initial average density of $0.3g/cm^3$ was used as samples. Oven-dried samples were immersed in water and vacuumed until fully saturated and then compressed by CSC at 120, 140, 160 or $180^{\circ}C$ for 10, 20, 30 or 40 min. The anatomical characteristics of transverse and radial sections before and after compression were compared by optical microscopy. The physical and mechanical properties, including the density, recovery of set (RS), modulus of elasticity (MOE), modulus of rupture (MOR), and compression parallel to grain were examined. It was observed that the anatomical characteristic of the inner part of OPT (i.e., vascular bundles, vessels, and parenchyma tissue) became flattened, fractured, and collapsed after compression by CSC. The RS decreased with increasing compression temperature and time. The lower RS indicated high dimensional stability. The physical and mechanical properties (i.e., density, MOR, MOE, and compressive strength) of the inner part of OPT increased with increasing compression temperature and time. Compression by the CSC method at $160^{\circ}C$ for 40 min was the optimum treatment.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.152-152
• /
• 2016

Anodizing is a technology to generate thicker and high-quality films than natural oxide films by treating metals via electrochemical methods. It is a technique to develop metals for various uses, and extensive research on the commercial use has been performed for a long time. Aluminum anodic oxide (AAO) is generate oxide films, whose sizes and characteristics depending on the types of electrolytes, voltages, temperatures and time. Electrochemical manufacturing method of nano structure is an efficient technology in terms of cost reduction, high productivity and complicated shapes, which receives the spotlight in diverse areas. The sulfuric acid was used as an anodizing electrolyte, controlling its temperature to $10^{\circ}C$. The anode was 5083 Al alloy with dimension of $5(t){\times}20{\times}20mm$ while the cathode was the platinum. The distance between the anode and the cathode was maintained at 3 cm. Agitation was introduced by magnetic stirrer at 300 rpm to prevent localized temperature rise that hinders stable growth of oxide layer. In order to observe surface characteristics with applied current density, the electrolyte temperature, concentration was maintained at constant condition for $10^{\circ}C$, 10 vol.%, respectively. To prevent hindrance of stable growth of oxide layer due to local temperature increase during the experiment, stirring was maintained at constant rate. In addition, using galvanostatic method, it was maintained at current density of $10{\sim}30mA/cm^2$ for 40 minutes. The cavitation experiment was carried out with an ultrasonic vibratory apparatus using piezo-electric effect with modified ASTM-G32. The peak-to-peak amplitude was $30{\mu}m$ and the distance between the horn tip and specimen was 1 mm. The specimen after the experiment was cleaned in an ultrasonic, dried in a vacuum oven for more than 24 hours, and weighed with an electric balance. The surface damage morphology was observed with 3D analysis microscope. As a result of the investigation, differences were observed surface hardness and anti-cavitation characteristics depending on the development of oxide film with applied current density.