• 한국전기전자재료학회논문지
• /
• 제23권6호
• /
• pp.458-463
• /
• 2010

MLCC (multi-layer ceramic capacitor) is usually fabricated by lamination of predetermined number of single layers. Often, the state of MLCC before sintering is called the green state, whose strength comes from the adhesion between the dielectric material and the polymer binder. Therefore the lamination of a single layer before sintering can be easily deformed by environment due to the relatively lower strength. After the compression process, which helps single sheets cohereto with adjacent sheets, the MLCC green bar is preheated to resolve the probable internal stress. Unfortunately, unexpected deformation after preheating resulted in problems during cutting of the MLCC green bar. In this study, one of 2 primary hypotheses which were proposed to resolve the unexpected deformation after preheating was examined by quantitative experiment with GC/MS (gas chromatograpy/mass spectrometer). The proportion of deformation caused by DOP evaporation, which was primarily evaporated componet during preheating, to the total deformation of the MLCC green bar was found to be 53%.

• 월간포장계
• /
• 통권262호
• /
• pp.74-77
• /
• 2015

• 한국표면공학회지
• /
• 제37권3호
• /
• pp.185-190
• /
• 2004

Plasma Display Panel is a display device emitting fluorescent light from gas discharge between a front and a rear panel sealed together. Front and rear panel have multitude of film layers and barrier ribs in the rear panel has the largest area so releasing various gases and affecting light emitting characteristics and lifetime. The remaining gases in a barrier rib were studied by thermal desorption analysis up to $400^{\circ}C$ and main gases were $H_2$ $H_2$O, CO. During sustaining at $300^{\circ}C$, the outgassing rates from other gases were decreased but$ H_2$ kept constantly increasing until 1 hour, which can be originated from the dissociation of organics remained in the inside of barrier rib material. In $H_2$O, two distinct peaks were observed: desorption from physically adsorbed one at $l00^{\circ}C$ and from chemically adsorbed one $400^{\circ}C$. The result can be utilized in interpretation of electronic and optical characteristics and evacuation process control of PDP

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.53-60
• /
• 1999

As the flying height decreased, it is essential that hard disk drives perform reliable under various environmental conditions. In this paper the tribological characteristics of a head/disk interface are investigated under various temperature, relative humidity, altitude and outgas conditions. Specially, Contact-Start-Stop(CSS) tests were performed to assess the stiction, acoustic emission, slider take-off behavior, and track average amplitude(TAA). It is shown that the surface damage and head failure are accelerated by high temperature and humidity as well as low ambient pressure.

• 대한토목학회논문집
• /
• 제40권1호
• /
• pp.51-58
• /
• 2020

달 탐사에 대한 관심이 늘어나면서 인공월면토를 포함한 달 지상 환경 모사에 대한 연구가 진행되고 있다. 인공월면토를 포함하여 진공환경을 조성할 때 발생하는 문제점 중의 하나는 토양에서 나오는 탈 가스로 인해 고진공에 도달하는 시간이 길어진다는 것이다. 이러한 탈 가스의 대부분은 수분이며, 진공챔버에 넣기 전 인공월면토의 표면에 붙어있는 수분을 제거하는 전처리 과정을 수행한다면 고진공에 도달하는 시간을 상당히 줄일 수 있다. 기존의 토양 건조 방법을 사용하여 각 방법이 인공월면토의 수분제거에 얼마나 효과적인지 확인하였다. 드라이 오븐을 이용한 방법, 마이크로웨이브 오븐을 이용한 방법, 직접가열 건조하는 방법과 진공 오븐을 이용한 방법을 이용하여 인공월면토 시료의 건조 실험을 수행하였으며, 건조 실험의 결과를 제시하였다. 실험결과 드라이 오븐에서 110℃로 건조하는 방법과 마이크로웨이브 오븐을 이용한 건조 방법은 수분제거 효과가 충분하지 않았으며, 200℃ 이상에서 진공오븐을 이용한 방법과 직접 가열하는 방법은 수분제거 효과가 좋았다.