• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.6
• /
• pp.458-463
• /
• 2010

MLCC (multi-layer ceramic capacitor) is usually fabricated by lamination of predetermined number of single layers. Often, the state of MLCC before sintering is called the green state, whose strength comes from the adhesion between the dielectric material and the polymer binder. Therefore the lamination of a single layer before sintering can be easily deformed by environment due to the relatively lower strength. After the compression process, which helps single sheets cohereto with adjacent sheets, the MLCC green bar is preheated to resolve the probable internal stress. Unfortunately, unexpected deformation after preheating resulted in problems during cutting of the MLCC green bar. In this study, one of 2 primary hypotheses which were proposed to resolve the unexpected deformation after preheating was examined by quantitative experiment with GC/MS (gas chromatograpy/mass spectrometer). The proportion of deformation caused by DOP evaporation, which was primarily evaporated componet during preheating, to the total deformation of the MLCC green bar was found to be 53%.

• The monthly packaging world
• /
• s.262
• /
• pp.74-77
• /
• 2015

• Journal of Surface Science and Engineering
• /
• v.37 no.3
• /
• pp.185-190
• /
• 2004

Plasma Display Panel is a display device emitting fluorescent light from gas discharge between a front and a rear panel sealed together. Front and rear panel have multitude of film layers and barrier ribs in the rear panel has the largest area so releasing various gases and affecting light emitting characteristics and lifetime. The remaining gases in a barrier rib were studied by thermal desorption analysis up to $400^{\circ}C$ and main gases were $H_2$ $H_2$O, CO. During sustaining at $300^{\circ}C$, the outgassing rates from other gases were decreased but$ H_2$ kept constantly increasing until 1 hour, which can be originated from the dissociation of organics remained in the inside of barrier rib material. In $H_2$O, two distinct peaks were observed: desorption from physically adsorbed one at $l00^{\circ}C$ and from chemically adsorbed one $400^{\circ}C$. The result can be utilized in interpretation of electronic and optical characteristics and evacuation process control of PDP

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.53-60
• /
• 1999

As the flying height decreased, it is essential that hard disk drives perform reliable under various environmental conditions. In this paper the tribological characteristics of a head/disk interface are investigated under various temperature, relative humidity, altitude and outgas conditions. Specially, Contact-Start-Stop(CSS) tests were performed to assess the stiction, acoustic emission, slider take-off behavior, and track average amplitude(TAA). It is shown that the surface damage and head failure are accelerated by high temperature and humidity as well as low ambient pressure.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.1
• /
• pp.51-58
• /
• 2020

As interest in lunar exploration increases, studies on lunar surface environment simulation including a lunar soil simulant are being conducted. One of the problems when creating a vacuum environment with lunar soil is that it takes long time to reach high vacuum due to outgas from the soil. Most of the outgas is water, and the time to reach high vacuum can be significantly reduced by a pretreatment process that removes moisture adhering to the surface of the lunar soil before putting soil into a vacuum chamber. The existing soil drying methods were examined to determine how these methods were effective to remove moisture from the lunar simulant soil. Drying experiments of lunar soil samples were carried out using a dry oven, a microwave oven, direct heating method and a vacuum oven, and the results of the drying experiment were presented. Drying soil at 110℃ using a dry oven and drying soil by a microwave oven were not enough to remove moisture, and vacuum oven drying method and direct heating drying method at more than 200℃ were effective in water removal.