• Korean Journal of Environmental Biology
• /
• v.32 no.1
• /
• pp.58-67
• /
• 2014

The outdoor mass cultivation is not possible for microalgae in Korea all year round, due to cold winter season. It is not easy to maintain proper level of productivity of microalgae even in winter. To prevent a drastic decrease of temperature in a greenhouse, two layers were covered additionally, inside the original plastic layer of the greenhouse. The middle layer was made up of plastic and the inner layer, of non-woven fabric. Acrylic transparent bioreactors were constructed to get more sunlight, not only from the upper side but also from the lateral and bottom directions. In winter at freezing temperatures, six different culture conditions were compared in the triply covered, insulated greenhouse. Wastewater after anaerobic digestion was used for the cultivation of microalgae to minimize the production cost. Water temperature in the bioreactors remained above $10^{\circ}C$ on average, even without any external heating system, proving that the triple-layered greenhouse is effective in keeping heat. Algal biomass reached to 0.37g $L^{-1}$ with the highest temperature, in the experimental group of light-reflection board at the bottom, with nitrogen and phosphorus removal rate of 92% and 99%, respectively. When fatty acid composition was analyzed using gas-chromatography, linoleate (C18 : 3n3) occupied the highest proportion up to 61%, in the all experiment groups. Chemical oxygen demand (COD), however, did not decrease during the cultivation, but rather increased. Although the algal biomass productivity was not comparable to warm seasons, it was possible to maintain water temperature for algae cultivation even in the coldest season, at the minimum cost.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.34 no.2
• /
• pp.87-99
• /
• 2016

This study was carried out to characterize 127 recently developed cultivars of Rose of Sharon (Hibiscus spp.) in Korea and foreign Countries for landscape uses. The examined factors were growth characteristics such as tree height of a 1-year grafted plant(cm), plant type, growth habit, leaf characteristics such as shape and size, flower characteristics such as color, shape, size, and red eye during 2014 and 2015 for landscape uses. The results are obtained as follows; Hibiscus hybrid 'Daewangchun', 'Daeil', 'Lohengrin', 'Yeonam', 'Joomong', 'Jina', and H. syriacus 'Honggarosu' had vigorous shoot growth and tall tree size of 100cm. New Hibiscus cultivars, Hibiscus hybrid 'Daewangchun' and 'Daeil', having vigorous growth, uniform plant habit, upright, and compact branches were developed through interspecific crosses between H. syriacus 'Samchully' (♀) and H. sinosyriacus 'Seobong' (♂). This newly developed cultivar 'Daewangchun', 'Daeil', 'Lohengrin', 'Yeonam', 'Joomong', 'Jina', and H. syriacus 'Honggarosu' having tall vigorous growth d unique flower with long red eye can be used as street tree or specimen plant in landscape. Otherwise, H. syriacus 'Tamla', 'Melrose', 'Bidan', 'Hi Lea', 'Byeollee', 'Byunghwa', 'Mibak', 'Hanyang', 'Chungam', 'Lil Kim Violet', 'Jongmoo', 'Eunhasu', Hibiscus hybrid 'Saehanseo', and Hibiscus hybrid 'Yousoon' were selected as small tree of 30~39cm. They had dwarf form in tree seemed to be suitable for pot or flower bed planting on both indoor and outdoor conditions. H. syriacus 'Antong', 'Chungjo', and 'Lil Kim' were less than 30 cm of tree size. H. syriacus 'Antong', 'Chungjo', and 'Lil Kim', characterized by its compact, upright and outwardly spreading plant habit; freely branching habit; dark green-colored leaves; good garden performance. Therefore, the new cultivars with tall and small tree size were a promising cultivar as a ground covers or pot planting as woody landscape plant.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.49 no.2
• /
• pp.51-60
• /
• 2021

Modern society is becoming more informed and intelligent with the development of digital technology, in which humans, objects, and networks relate with each other. In accordance with the changing times, a garden system has emerged that makes it easy to supply the ideal temperature, humidity, sunlight, and moisture conditions to grow plants. Therefore, this study attempted to grasp the concept, perception, and trends of smart gardens, a recent concept. To achieve the purpose of this study, previous studies and text mining were used, and the results are as follows. First, the core characteristics of smart gardens are new gardens in which IoT technology and gardening techniques are fused in indoor and outdoor spaces due to technological developments and changes in people's lifestyles. As technology advances and the importance of the environment increases, smart gardens are becoming a reality due to the need for living spaces where humans and nature can co-exist. With the advent of smart gardens, it will be possible to contribute to gardens' vitalization to deal with changes in garden-related industries and people's lifestyles. Second, in current research related to smart gardens and users' experiences, the technical aspects of smart gardens are the most interesting. People value smart garden functions and technical aspects that enable a safe, comfortable, and convenient life, and subjective uses are emerging depending on individual tastes and the comfort with digital devices. Third, looking at the usage behavior of smart gardens, they are mainly used in indoor spaces, with edible plants are being grown. Due to the growing importance of the environment and concerns about climate change and a possible food crisis, the tendency is to prefer the cultivation of plants related to food, but the expansion of garden functions can satisfying users' needs with various technologies that allow for the growing of flowers. In addition, as users feel the shapes of smart gardens are new and sophisticated, it can be seen that design is an essential factor that helps to satisfy users. Currently, smart gardens are developing in terms of technology. However, the main components of the smart garden are the combination of humans, nature, and technology rather than focusing on growing plants conveniently by simply connecting potted plants and smart devices. It strengthens connectivity with various city services and smart homes. Smart gardens interact with the landscape of the architect's ideas rather than reproducing nature through science and technology. Therefore, it is necessary to have a design that considers the functions of the garden and the needs of users. In addition, by providing citizens indoor and urban parks and public facilities, it is possible to share the functions of communication and gardening among generations targeting those who do not enjoy 'smart' services due to age and bridge the digital device and information gap. Smart gardens have potential as a new landscaping space.

• Journal of Bio-Environment Control
• /
• v.5 no.2
• /
• pp.215-235
• /
• 1996

The thermal analysis by mathematical model simulation makes it possible to reasonably predict heating and/or cooling requirements of certain greenhouses located under various geographical and climatic environment. It is another advantages of model simulation technique to be able to make it possible to select appropriate heating system, to set up energy utilization strategy, to schedule seasonal crop pattern, as well as to determine new greenhouse ranges. In this study, the control pattern for greenhouse microclimate is categorized as cooling and heating. Dynamic model was adopted to simulate heating requirements and/or energy conservation effectiveness such as energy saving by night-time thermal curtain, estimation of Heating Degree-Hours(HDH), long time prediction of greenhouse thermal behavior, etc. On the other hand, the cooling effects of ventilation, shading, and pad ||||&|||| fan system were partly analyzed by static model. By the experimental work with small size model greenhouse of 1.2m$\times$2.4m, it was found that cooling the greenhouse by spraying cold water directly on greenhouse cover surface or by recirculating cold water through heat exchangers would be effective in greenhouse summer cooling. The mathematical model developed for greenhouse model simulation is highly applicable because it can reflects various climatic factors like temperature, humidity, beam and diffuse solar radiation, wind velocity, etc. This model was closely verified by various weather data obtained through long period greenhouse experiment. Most of the materials relating with greenhouse heating or cooling components were obtained from model greenhouse simulated mathematically by using typical year(1987) data of Jinju Gyeongnam. But some of the materials relating with greenhouse cooling was obtained by performing model experiments which include analyzing cooling effect of water sprayed directly on greenhouse roof surface. The results are summarized as follows : 1. The heating requirements of model greenhouse were highly related with the minimum temperature set for given greenhouse. The setting temperature at night-time is much more influential on heating energy requirement than that at day-time. Therefore It is highly recommended that night- time setting temperature should be carefully determined and controlled. 2. The HDH data obtained by conventional method were estimated on the basis of considerably long term average weather temperature together with the standard base temperature(usually 18.3$^{\circ}C$). This kind of data can merely be used as a relative comparison criteria about heating load, but is not applicable in the calculation of greenhouse heating requirements because of the limited consideration of climatic factors and inappropriate base temperature. By comparing the HDM data with the results of simulation, it is found that the heating system design by HDH data will probably overshoot the actual heating requirement. 3. The energy saving effect of night-time thermal curtain as well as estimated heating requirement is found to be sensitively related with weather condition: Thermal curtain adopted for simulation showed high effectiveness in energy saving which amounts to more than 50% of annual heating requirement. 4. The ventilation performances doting warm seasons are mainly influenced by air exchange rate even though there are some variations depending on greenhouse structural difference, weather and cropping conditions. For air exchanges above 1 volume per minute, the reduction rate of temperature rise on both types of considered greenhouse becomes modest with the additional increase of ventilation capacity. Therefore the desirable ventilation capacity is assumed to be 1 air change per minute, which is the recommended ventilation rate in common greenhouse. 5. In glass covered greenhouse with full production, under clear weather of 50% RH, and continuous 1 air change per minute, the temperature drop in 50% shaded greenhouse and pad ＆ fan systemed greenhouse is 2.6$^{\circ}C$ and.6.1$^{\circ}C$ respectively. The temperature in control greenhouse under continuous air change at this time was 36.6$^{\circ}C$ which was 5.3$^{\circ}C$ above ambient temperature. As a result the greenhouse temperature can be maintained 3$^{\circ}C$ below ambient temperature. But when RH is 80%, it was impossible to drop greenhouse temperature below ambient temperature because possible temperature reduction by pad ||||&|||| fan system at this time is not more than 2.4$^{\circ}C$. 6. During 3 months of hot summer season if the greenhouse is assumed to be cooled only when greenhouse temperature rise above 27$^{\circ}C$, the relationship between RH of ambient air and greenhouse temperature drop($\Delta$T) was formulated as follows : $\Delta$T= -0.077RH＋7.7 7. Time dependent cooling effects performed by operation of each or combination of ventilation, 50% shading, pad ＆ fan of 80% efficiency, were continuously predicted for one typical summer day long. When the greenhouse was cooled only by 1 air change per minute, greenhouse air temperature was 5$^{\circ}C$ above outdoor temperature. Either method alone can not drop greenhouse air temperature below outdoor temperature even under the fully cropped situations. But when both systems were operated together, greenhouse air temperature can be controlled to about 2.0-2.3$^{\circ}C$ below ambient temperature. 8. When the cool water of 6.5-8.5$^{\circ}C$ was sprayed on greenhouse roof surface with the water flow rate of 1.3 liter/min per unit greenhouse floor area, greenhouse air temperature could be dropped down to 16.5-18.$0^{\circ}C$, whlch is about 1$0^{\circ}C$ below the ambient temperature of 26.5-28.$0^{\circ}C$ at that time. The most important thing in cooling greenhouse air effectively with water spray may be obtaining plenty of cool water source like ground water itself or cold water produced by heat-pump. Future work is focused on not only analyzing the feasibility of heat pump operation but also finding the relationships between greenhouse air temperature(T$_{g}$ ), spraying water temperature(T$_{w}$ ), water flow rate(Q), and ambient temperature(T$_{o}$).

• The Korean Journal of Mycology
• /
• v.7 no.1
• /
• pp.13-73
• /
• 1979

These studies were conducted to investigate nutrient sources and supplementary materials of synthetic compost media for Agaricus bisporus culture. Investigation were carried out to establish the optimum composition for compost of Agaricus bisporus methods of out-door fermentation and peakheating with rice straw as the main substrate of the media. The incidence and flora of harmful organisms in rice straw compost and their control were also studied. 1. When rice straw was used as the main substrate in synthetic compost as a carbon source. yields were remarkably high. Fermentation was more rapid than that of barley straw or wheat straw, and the total nitrogen content was high in rice straw compost. 2. Since the morphological and physico-chemical nature of Japonica and Indica types of rice straw are greatly dissimilar. there were apparent differences in the process of compost fermentation. Fermentation of Indica type straw proceeded more rapidly with a shortening the compost period, reducing the water supply, and required adding of supplementary materials for producing stable physical conditions. 3. Use of barley straw compost resulted in a smaller crop compared with rice straw. but when a 50%, barley straw and 50% rice straw mixture was used, the yield was almost the same as that using only rice straw. 4. There were extremely high positive correlations between yield of Agaricus bisporus and the total nitrogen, organic nitrogen, amino acids, amides and amino sugar nitrogen content of compost. The mycerial growth and fruit body formation were severely inhibited by ammonium nitrogen. 5. When rice straw was used as the main substrate for compost media, urea was the most suitable source of nitrogen. Poor results were obtained with calcium cyanamide and ammonium sulfate. When urea was applied three separate times, nitrogen loss during composting was decreased and the total nitrogen content of compost was increased. 6. The supplementation of organic nutrient activated compost fermentation and increased yield of Agaricus bisporus. The best sources of organic nutrients were: perilla meal, sesame meal, wheat bran and poultry manure, etc. 7. Soybean meal, tobacco powder and glutamic acid fermentation by-products which were industrial wastes, could be substituted for perilla meal, sesame meal and wheat bran as organic nutrient sources for compost media. B. When gypsum and zeolite were added to rice straw. physical deterioration of compost due to excess moisture and caramelization was observed. The Indica type of straw was more remarkable in increase of yield of Agricus bisporus by addition of supplementing materials than Japonica straw. 9. For preparing rice straw compost, the best mixture was prepared by 10% poultry manure, 5% perilla meal, 1. 2 to 1. 5% urea and 1% gypsum. At spring cropping, it was good to add rice bran to accelerate heat generation of the compost heap. 10. There was significantly high positive correlation (r=0.97) between accumulated temperature and the decomposition degree of compost during outdoor composting. The yield was highest at accumulated temperatures between 900 and $1,000^{\circ}C$. 11. Prolonging the composting period brought about an increase in decomposition degree and total nitrogen content, but a decrease in ammonium nitrogen. In the spring the suitable period of composting was 20 to 25 days. and about 15 days in autumn. For those periods, the degree of decomposition was 19 to 24%. 12. Compactness of wet compost at filling caused an increase in the residual ammonium nitrogen. methane and organic acid during peak heating. There was negative correlation between methane content and yield (r=0.76)and the same was true between volatile organic acid and yield (r=0.73). 13. In compost with a moisture content range between 69 to 80% at filling. the higher the moisture content, the lower the yield (r=0.78). This result was attributed to a reduction in the porosity of compost at filling the beds. The optimum porosity for good fermentation was between 41 and 53%. 14. Peak heating of the compost was essential for the prevention of harmful microorganisms and insect pests. and for the removal of excess ammonia. It was necessary to continue fer mentatiion for four days after peak heating. 15. Ten species of fungi which are harmful or competitive to Agaricus bisporus were identified from the rice compost, including Diehliomyces microsporus, Trichoderma sp. and Stysanus stemoites. The frequency of occurrance was notably high with serious damage to Agaricus bisporus. 16. Diehliomyces microsporus could be controlled by temperature adjustment of the growing room and by fumigating the compost and the house with Basamid and Vapam. Trichoderma was prevented by the use of Bavistin and Benomyl. 17. Four species of nematodes and five species of mites occured in compost during out-door composting. These orgnanisms could be controlled through peakheating compost for 6 hours at $60^{\circ}C$.