• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.246-250
• /
• 2015

In this paper, Timoshenko and Euler-Bernoulli beam theories(EB-beam) are used, and Fast Fourier Transformation(FFT) analysis is then employed to extract their natural frequencies using both analytical approach and Co-rotational plane beam(CR-beam) EDISON program. EB-beam is used to analyze a spring-mass system with a single degree of freedom. Sinusoidal force with various frequencies and constant magnitude are applied to tip of each beam. After the oscillatory tip response is observed in EB-beam, it decreases and finally converges to the so-called 'steady-state.' The decreasing rate of the tip deflection with respect to time is reduced when the forcing frequency is increased. Although the tip deflection is found to be independent of the excitation frequency, it turns out that time to reach the steady state response is dependent on the forcing frequency.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.905-906
• /
• 2006

This paper deals with the dynamic simulations and experiments of moving-coil linear actuator with/without spring. Dynamic simulation algorithm is established from the voltage and motion equation. Finally, for various values of frequency, dynamic simulation results for characteristics of current and displacement of moving-coil linear actuator with and without spring are presented and confirmed through the experiments.

• Proceedings of the KIEE Conference
• /
• 1997.07c
• /
• pp.1056-1059
• /
• 1997

Thyristor-Controlled Series Compensation (TCSC) is expected to be applied in transmission systems to achieve a number of benefits. TCSC can provide such assistance for stability, as well as helping to direct flows onto desired transmission paths. This paper describess a TCSC model which can be used for typical transient and oscillatory stability studies. Also included is a discussion on relevant information to extend the modeling detail of the TCSC for use stability analysis.

• Journal of Ship and Ocean Technology
• /
• v.4 no.2
• /
• pp.13-23
• /
• 2000

A low-order potential based boundary element method is applied to the prediction of the flow around the cavitating propeller in steady or in unsteady inflow. For given cavitation number, the cavity shape is determined in an iterative manner until the kinematic and the dynamic boundary conditions are both satisfied on the approximate cavity boundary. In order to improve the solution behavior near the tip region, a hyperboloidal panel geometry and a modified split panel method are applied. The method is then extended to include the analysis of time-varying cavitating flows around the propeller blades via a time-step algorithm in time domain. In the method, the steady state oscillatory solution is obtained by incremental stepping in the itme domain. Finally, the present method is validated through comparison with other numerical results and experimental data.

• Journal of Magnetics
• /
• v.4 no.1
• /
• pp.17-21
• /
• 1999

The GMR ($d_Cu$) oscillatory behaviour as well as the widths of first and the second antiferromagnetically coupled ranges of the Permalloy ($Py=Ni_{83}Fe_{17}$)/Cu multilayers have been found to be strongly affected not only by the presence of the superparamagnetic/paramagnetic entitles located at the Py/Cu interfaces but mainly by the existence of the magnetic bridges between Py layers. The effectiveness of the magnetic bridges has been found to be temperature dependent, leading to the temperature dependence of the remnant to saturation magnetization ratio ($M_R/M_S$). We have found that for Py/Cu multilayers with equal Py and Cu layer thicknesses a high field sensitivity of the GMR effect (0.4%/Oe) and negligible hysteresis can be achieved when the number of Py layers decreases from 100 to 6. Sensitivity can be further improved by increasing the Py layers thickness, but the hysterstic effect becomes more pronounced then.

• Transactions of Materials Processing
• /
• v.25 no.5
• /
• pp.325-331
• /
• 2016

In this paper, a three-dimensional part model is constructed for the finite element analysis of hemming models where hemming defects frequently occur. The roller path is modeled as the boundary condition with the one-dimensional beam element and the revolute joint model. With the constructed part model and the roller movement, a finite element analysis has been pursued in order to identify the hemming load and hemming defects such as wrinkling in the flange region. The analysis result shows that the maximum hemming load occurs in the intake situation while oscillatory behavior of the load is found especially when hemming the curved model because of wrinkle generation. This paper compares the amplitude and the period of wrinkle between the analysis result and the experiment, which shows good agreement with each other.

• Proceedings of the Korean Biophysical Society Conference
• /
• 2003.06a
• /
• pp.78-78
• /
• 2003

The glycolysis is one of the most important metabolic reactions through which the glucose is broken and the released energy is stored in the form of ATP. Rhythmic oscillation of the intracellular ATP is observed as the amount of the influx glucose is small in the yeast. The oscillation is also observed in the population of the yeast cells, which implies that the glycolytic oscillation of the yeasts is synchronous. It is not clear how the synchronous oscillation could be organized among the yeast cells. Although detailed mathematical models are available that show synchronization of the glycolytic oscillation, the stability of the synchronous oscillation is not clear. We introduce a phase model analysis that reduces a higher dimensional mathematical model to a much simpler one dimensional phase model. Then, the stability of the synchronous oscillation is easily determined by the stability of the corresponding fixed solution in the phase model. The effect of perturbation on the oscillatory rhythm is also easily analyzed in the reduced phase model.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.3
• /
• pp.302-307
• /
• 2006

The aim of applying Functional Electrical Stimulation (FES) is to restore a person's motor function by directly supplying the controlled electrical currents to the site of the paralyzed muscles. However, most clinically utilized FES systems have adapted an open-loop control scheme. Recently the closed-loop control scheme has been considered for setting up the FES system, but due to the inherent nonlinearities in the musculoskeletal system, the nonlinearities were not fully compensated and it caused the oscillatory responses for tracking the output variables. In this study, a nonlinear controller model that has two inverse compensation units is proposed with the compromising feedback linearization method and this will eventually be used to design the FES control system for stimulating a knee joint musculoskeletal system.

• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.81-85
• /
• 2010

This paper deals with the issue of motion control of a single rod cylinder-load system using simple adaptive control (SAC) method. Prior to controller design, the experiment of open-loop response has been performed. Based on it, design parameters of transfer function are obtained. The effect of parallel feedforward compensator has been investigated by computer simulation, suppressing the oscillatory motion. Through experiments it is conformed that the SAC method gives good tracking performance compared to the PD control method.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.900-902
• /
• 2000

A moving-coil-type linear oscillatory actuator is consisted of the NdFeB permanent magnets with high specific energy as the stator, a coil-wrapped nonmagnetic hollow rectangular structure and an iron core as a pathway for magnetic flux. The inductance of moving coil and the push/pull effect is obtained from the permeance model of LOA with the open magnetic circuit. The analytical method are verified using the 2D finite element method.