• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.42-49
• /
• 2010

In general, the direct experimental approach to study machining processes is expensive and time consuming, especially when a wide range of parameters are included: tool, geometry, materials, cutting conditions, etc. The aim of this study is to verify the effectiveness of finite element method for orthogonal cutting process by comparing the simulated cutting forces with measured results. Two commercialized finite element codes $AdvantEdge^{TM}$ and Deform-$2D^{TM}$ have been used to simulate the cutting forces in orthogonal cutting process. In this paper, estimated cutting and feed force components are compared with experimental results for different two materials. As a result, it has been found that FEM simulation is effective for understanding and predicting the orthogonal cutting process although some improvements on friction model and remeshing process are needed.

• 한국산업융합학회 논문집
• /
• 제7권4호
• /
• pp.419-424
• /
• 2004

In order to increase the efficiency of the sawdust machine, the helical type drums with an oblique cutting condition (3D) were developed. The preexisting drums have an orthogonal cutting condition (2D) considering of a saw cutter and a wood cutting pattern. Unfortunately, the disadvantages of this type drum are the big cutting resistance, the high cost of a cutting power and the extreme occurrence of a vibration. To improve this shortcoming, the helical type drum with an oblique cutting condition was developed. Therefore, this type drum decreased the vibration and the cutting resistance of the sawdust machine, and also improved the productivity of 30% or more and the porosity of the sawdust.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.88-92
• /
• 2004

We developed a helical type drum with an oblique cutting condition for sawdust machine. The existing drum has an orthogonal cutting(2D) condition considering of saw cutter and wood cutting pattern. Additional disadvantage of this type include big cutting resistance, high cost of cutting power and extreme occurrence of vibrations. To improve this shortcoming, we developed a helical type drum with an oblique cutting(3D) condition, therefore, this type drum decreased the vibration and cutting resistance of sawdust machine, and also improved productivity and sawdust porosity.

• 한국정밀공학회지
• /
• 제29권8호
• /
• pp.853-862
• /
• 2012

The present study develops a method for directly measuring the temperature field in the primary deformation zone with a high spatial resolution during 2-D orthogonal machining. This is enabled by the use of a high-speed, charge-coupled device (CCD) based, infra-red (IR) imaging system which allows characteristics of the temperature field such as the location and magnitude of the highest temperature and temperature gradient in the primary deformation zone to be identified. Based on these data, the relation between the machining temperature and the cutting conditions is investigated.

• Design & Manufacturing
• /
• 제11권2호
• /
• pp.46-50
• /
• 2017

EPS used in lost foam casting elastic modulus is extremely low. So it is necessary to derive machining conditions for effective cutting. Therefore this study were analyzed end-milling machining conditions to affecting the surface roughness of EPS foam. The machining conditions were set to depth, feed, and RPM at 3-level. And 18experimental conditions were derived using mixed orthogonal array. The most important condition for surface roughness is RPM. In addition, RPM machining condition range test that can realize surface roughness less than $10{\mu}m$ was performed. he range of RPM conditions is more than 15,000. However the range of RPM conditions is a condition that is difficult to use in actual field. In the future variance analysis and experiments are needed to derive the range of machining conditions available.

• 한국정밀공학회지
• /
• 제29권3호
• /
• pp.279-288
• /
• 2012

The material removal mechanism in machining is significantly affected by the cutting edge geometry. Its effect becomes even more substantial when the depth of cut is relatively small as compared to the characteristic length which represents the shape and size of the cutting edge. Conventionally, radius or focal length has been employed as the characteristic length with the assumption that the shape of cutting edge is round or parabolic. However, in reality, there could be various ways to determine the radius or focal length even for the same tool edge profile, depending on the region to be considered as cutting edge in the measured profile and the constraints to be set in constructing the best fitted circle or parabola. In this regard, the present study proposes various models to determine the characteristic length in terms of radius or focal length. Their physical compatibility are validated by carrying out 2D orthogonal cutting experiments using inserts with a wide range of characteristic length ($30{\sim}180\;{\mu}m$ in terms of radius) and then by investigating the correlation between the characteristic length and the cutting forces. Such validation is based on the common belief that the larger the characteristic length is, the blunter the cutting edge is and the higher the cutting forces are. Interestingly, the results showed that the correlation is higher for the radius or focal length obtained with a constraint that the center of best fitted circle or the focus of the best fitted parabola should be on the bisectional line of the wedge angle of tool.

• 한국정밀공학회지
• /
• 제13권4호
• /
• pp.61-66
• /
• 1996

The subsequent recrystallizations technique, and experimental strain measurement method by use of recrystallization phenomena, has been successfully applied for the observation of machined surface plastic zones with equivalent plastic strain .epsilon. .geq. 0.5, 0.12 and 0.02 of type 304 stainless steel. The depth of the zone with .epsilon. .geq. 0.5 is very small, 10-15 .mu. m, while those with .epsilon. .geq. 0.12 are 100-200 .mu. m and 200-450 .mu. m, respectively. The depths increase with increasing depth of cut and with decreasing rake angle. The relation between the depth of the zones and the cutting paramenters is shown. The deformation state ahead of the quick-stop cut was also well visualized by the technique.

• Steel and Composite Structures
• /
• 제34권5호
• /
• pp.681-698
• /
• 2020

The paper addresses contribution to the modeling and optimization of major machinability parameters (cutting force, surface roughness, and tool wear) in finish dry hard turning (FDHT) for machinability evaluation of hardened AISI grade die steel D₃ with PVD-TiN coated (Al₂O₃-TiCN) mixed ceramic tool insert. The turning trials are performed based on Taguchi's L₁₈ orthogonal array design of experiments for the development of regression model as well as adequate model prediction by considering tool approach angle, nose radius, cutting speed, feed rate, and depth of cut as major machining parameters. The models or correlations are developed by employing multiple regression analysis (MRA). In addition, statistical technique (response surface methodology) followed by computational approaches (genetic algorithm and particle swarm optimization) have been employed for multiple response optimization. Thereafter, the effectiveness of proposed three (RSM, GA, PSO) optimization techniques are evaluated by confirmation test and subsequently the best optimization results have been used for estimation of energy consumption which includes savings of carbon footprint towards green machining and for tool life estimation followed by cost analysis to justify the economic feasibility of PVD-TiN coated Al₂O₃+TiCN mixed ceramic tool in FDHT operation. Finally, estimation of energy savings, economic analysis, and sustainability assessment are performed by employing carbon footprint analysis, Gilbert approach, and Pugh matrix, respectively. Novelty aspects, the present work: (i) contributes to practical industrial application of finish hard turning for the shaft and die makers to select the optimum cutting conditions in a range of hardness of 45-60 HRC, (ii) demonstrates the replacement of expensive, time-consuming conventional cylindrical grinding process and proposes the alternative of costlier CBN tool by utilizing ceramic tool in hard turning processes considering technological, economical and ecological aspects, which are helpful and efficient from industrial point of view, (iii) provides environment friendliness, cleaner production for machining of hardened steels, (iv) helps to improve the desirable machinability characteristics, and (v) serves as a knowledge for the development of a common language for sustainable manufacturing in both research field and industrial practice.