• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.160-165
• /
• 2004

MPA (Multi-Point Averaging) flow element is a new type of differential pressure (DP) flow-sensing device that was developed by Seojin Instech to improve the operating characteristics of the conventional Averaging Pilot Tube (APT) flow elements. Operating characteristics of a flowmeter in general can be defined in terms of measurement accuracy and range. Improvement of accuracy and expanding the range of flow measurement were the two main objectives of the development. To achieve these dual objectives several upstream and downstream pressure-sensing holes were placed in MPA flow element. During the course of the development it was found that certain arrangements of the pressure-sensing holes improved measurement accuracy but did not expand operating flow range of Averaging Pilot Tubes. Development tests were performed with water between Reynolds number of 50,000 and 1,000,000 in the four-inch test line at the Alden Research Laboratory, U.S.A. Purpose of this paper is to present the relationship between the various locations of the pressure-sensing holes and the performance characteristics of MPA flow element. Furthermore, the operating characteristics of the best performing MPA are compared with those of typical orifice and APT.

• 대한안전경영과학회지
• /
• 제12권4호
• /
• pp.93-98
• /
• 2010

본 연구에서는, 반도체, LCD 공정에서 금속막을 증착하기 위하여 PECVD장비에 화재, 폭발 위험성과 독성을 가진 Silane가스를 사용하게 되는 장비인 gas cabinet, pipeline, VMB(Valve manifold box), MFC(mass flow controller)장비 등, 전반적인 시스템에 대하여 영국 HES의 ALARP개념을 도입하여 위험성 평가를 실시하여 문제점을 도출하고 대책을 강구 하는데 목적이 있고, 여러 가지 문제점중 절대적으로 수용 할 수 없는 Critical Risk로는 Gas Cylinder를 사용하여 Silane을 공급하고자 할 때에는 필히 Gas Cabinet을 사용하여 공급하여야 하고, Tube Trailer를 사용하여 공급하고자 할 때에는 필수적으로 Purge System을 갖추어 공급하여야 한다. 선택적으로 수용할 수 있는 High, Medium Risk로는 Gas Cylinder 또는 Tube Trailer를 사용하여 Silane을 공급하고자 할 때는 Inlet 부분에 RFO(Resticted Flow Orifice)를 설치하여 사용하고 Gas Supply Room에는 CO2소화설비를 적용하지 말고 Water Mist등 물 분무설비를 적용하여야한다.

• 대한기계학회논문집B
• /
• 제21권10호
• /
• pp.1273-1283
• /
• 1997

Experiments of shock wave/turbulent boundary layer interaction were conducted by using a supersonic wind tunnel. Nominal Mach number was varied in the range of 1.6 to 3.0 by means of different nozzles. The objective of the present study is to investigate the effects of boundary layer flow bleed on the interaction flow field in a straight tube. Two-dimensional slits were installed on the tube walls to bleed the turbulent boundary layer flows. The bleed flows were measured by an orifice. The ratio of the bleed mass flow to main mass flow was controlled within the range of 11 per cent. The wall pressures were measured by the flush mounted transducers and Schlieren optical observations were made for almost all of the experiments. The results show that the boundary layer flow bleed reduces the multiple shock waves to a strong normal shock wave. For the design Mach number of 1.6, it was found that the normal shock wave at the position of the silt was resulted from the main flow choking due to the suction of the boundary layer flow.

• 드라이브 ㆍ 컨트롤
• /
• 제16권1호
• /
• pp.1-6
• /
• 2019

The use of micro bubbles in industrial fields has been increasing in the recent years., particularly micro-bubble sterilization and water purification effects. Various methods have been developed for the generation of micro-bubbles. Depending on the method of generating bubbles, the micro-bubbles can be roughly classified into saturation molding, cavitation and rotation flow types. The objective of this study was to use ventilated tube type as a method of generating micro-bubbles in order to purify large amount of water quality such as lakes and reservoirs. This method shows a difference in efficiency in which micro-bubbles are generated depending on the contact ratio of gas to liquid. The study also investigated the optimal gas liquid contact ratio by applying various orifice methods and investigated the optimum condition of micro-bubble generation by gas Based on this, a technology to develop a micro-bubble generator with a venturi type nozzle shape that has a high water purification effect was developed.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.435-439
• /
• 2002

In the pneumatic system, pneumatic cylinder is wildly used to factory automation. In general, Pneumatic cylinder problems are occured with colliding to stroke end part at which piston collide to end-cap, head cap and tube when piston is loading. This appearances have a short life of cylinder and is due to system destruction. This study examines the dynamic characteristics of pneumatic cushioning cylinder and cushion sleeve design. At head part cushion chamber for the vertical experimental, The decisions of cushioning effect and the results of the experimental research are obtained to the followings: i) The cushioning effects could acqure to the reserch, if the compressible energy is more than kinetic ones. ii) The collision of piston and head cover could acqure to the research, if the kinetic energy is more than compressible iii) If the load increase to the rolling car, the cushion region pressures would increase and the dynamic force.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1995년도 추계 총회 및 학술발표회
• /
• pp.5-9
• /
• 1995

In the dry-jet-wet-spinning process of a hollow fiber membrane, the polymer solution is pumped into a coaxial tube, jet spinneret. The threadline emerging from the spinneret is stabilized by an internal coagulating medium(liquid or gas) as it emerges from the jet orifice. The nascent hollow thread is further stabilized in a quench bath as shown in Fig. 1. In this scheme, three mechanism of formatiota(temperature gradient, solvent evaporation, and solvent-nonsotvent exchange) can be combined. The changes which promote stabilization often play a dominant role in determining the ultimate fiber wall structure as well. Hence, in pratice, hollow fiber stabilization and development of membrane structure are commonly inseparable. However, fiber dimension(the inside diameter and wall thickness of the hollow fiber) is mainly a rheological problem and is determined by dope pumping rate, spinneret diatance from the coagulation bath, inner coagulant flow rate, and fiber draw-rate. Besides rheological phenomena play a prominent part in the final properties of the hollow fiber.

• 항공우주시스템공학회지
• /
• 제6권2호
• /
• pp.13-17
• /
• 2012

In this study the flow rate-to-pressure difference characteristics of short-tube type damping orifices for a aircraft door damper were investigated by CFD analyses. For the verification of the CFD analysis results the actual performance of a door damper was measured and compared with them. and The dynamic response of door damper is Simulated using ADAMS. it's performance is evaluated comparing to the experiment result of door damper.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권5호
• /
• pp.500-509
• /
• 2013

SCR 머플러 입구와 촉매사이에 설치되는 다공튜브 형상변화에 따른 촉매 삽입형 urea-SCR 머플러 내부유동특성이 해석적으로 조사되었다. 다공튜브는 요소수 분무와 배기가스 혼합물의 공간분포 향상을 통한 $NO_x$ 저감율 증대 및 암모니아 슬립을 방지하기 위해 사용되는 장치이다. 다공튜브 오리피스 면적비 변화가 챔버 내부 유동 및 촉매 전후단의 속도분포에 끼치는 영향이 조사되었으며, 속도분포에 대한 균일도 지수가 최적설계 관점에서 평가되었다. 해석은 상용 유동해석 프로그램을 이용하여 정상상태에서 수행되었으며 요소수 분무와 배기가스 혼합물 대신 상온의 공기가 작동유체로 사용되었다. 해석결과로부터 다공튜브 형상은 머플러 입구와 촉매 전단 사이에 형성된 챔버 내 벌크 선회유동과 촉매 전후단 속도분포의 균일도지수에 큰 영향을 끼침을 알 수 있었다.

• 대한의용생체공학회:의공학회지
• /
• 제28권6호
• /
• pp.768-776
• /
• 2007

A new type of the fluid circulation blood pressure simulator was proposed to enhance the blood pressure simulator used for the development and evaluation of automatic sphygmomanometers. Various pressure waveform of fluid flowing in the pipe was reproduced by operating the proportional control valve after applying a pressure on the fluid in pressurized oil tank. After that, appropriate fluid was supplied by operating the proportional control valve, which enabled to reproduce various pressure wave of the fluid flowing in the tube. To accomplish this work, the mathematical model was carefully reviewed in cooperating with the proposed simulator. After modeling the driving signal as input signal and the pressure in internal tube as output signal, the simulation on system parameters such as internal volume, cross-section of orifice and supply pressure, which are sensitive to dynamic characteristic of system, was accomplished. System parameters affecting the dynamic characteristic were analyzed in the frequency bandwidth and also reflected to the design of the plant. The performance evaluator of fluid dynamic characteristic using proportional control signal was fabricated on the basis of obtained simulation result. An experimental apparatus was set-up and measurements on the dynamic characteristic, nonlinearity, and rising and falling response was carried out to verify the characteristic of the fluid dynamic model. Controller was designed and thereafter, simulation was performed to control the output signal with respect to the reference input in the fluid dynamic model using the proposed proportional control valve. Hybrid controller combined with an proportional controller and feed-forward controller was fabricated after applying a disturbance observer to the control plant. Comparison of the simulations between the conventional proportional controller and the proposed hybrid simulator indicated that even though the former showed good control performance.

• 대한기계학회논문집A
• /
• 제34권12호
• /
• pp.1901-1907
• /
• 2010

굴삭기 유압실린더는 붐, 암, 버킷과 같은 작업장치를 작동시키는 핵심 부품이다. 일반적으로 유압실린더는 반복적인 고압으로 인해 좌굴이나 피로 파손과 같은 구조적 문제가 종종 발생한다. 따라서, 유압실린더의 내구설계 시 설계수명 동안의 피로, 항복, 좌굴 등에 대한 구조 안전도 평가가 반드시 이루어져야 한다. 내구설계는 기본설계와 상세설계 두 단계로 구성되는데, 기본설계 단계에서는 굴삭기의 작업능력, 작업속도, 작업영역 등을 고려하여 항복과 좌굴 안전도를 만족하도록 로드와 튜브의 주요 치수를 결정한다. 상세설계 단계에서는 로드 노치, 용접부, 튜브 끝단, 글랜드, 오리피스, 쿠션링 등의 상세치수를 주로 피로 안전도 측면에서 결정한다. 본 연구에서는 이러한 내구설계의 전반적인 절차와 각 설계 단계에서 내구설계 평가를 위한 해석기법에 대해 기술하였다.