• International Journal of Aeronautical and Space Sciences
• /
• 제3권1호
• /
• pp.1-8
• /
• 2002

A numerical analysis was performed on the fluid flow in injector orifice of a liquid rocket engine. The present computational code was verified against the published data for turbulent flow in a pipe with a sudden expansion-contraction. Considered were the parameters for the flow analysis in an injector orifice: Reynolds number, ratio of mass flow rate of the injector orifice and inlet flow rate, and slant angle of the injector orifice. The discharge coefficient increased slightly as the Reynolds number increased. The slant angle of the injector changed critically the discharge coefficient. The discharge coefficient increased by 7% when the slant angle changed from $-30^{\circ}$ to $30^{\circ}$ The ratio of mass flow rate had relatively little impact on the discharge coefficient.

• 한국분무공학회지
• /
• 제8권2호
• /
• pp.7-15
• /
• 2003

The effects of fuel density and fuel viscosity on spray characteristics were investigated under two different gas turbine fuels and various fuel supply pressure conditions through measurement of SMD, number density and volume flux by using PDPA system in dual orifice injector for gas turbine engines. In this study, we found out that the droplet size and spray structure are strongly depend on fuel density for dual orifice injector. The spray characteristics of high density fuel in dual orifice injector are similar with the characteristics of low density fuel in single orifice injector. The shear region between primary main fuel stream and secondary main fuel stream is examined in low density fuel condition but not exist in high density fuel condition, then this shear region is very important in quality of gas turbine spray. There are worth consideration for the effect of fuel density on spray characteristics in frontal device design to improve combustion efficiency.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.300-303
• /
• 2010

다양한 형상의 인젝터 내부 젤 추진제 유동을 수치적으로 연구하였다. 모사 젤 추진제의 유변학적물성치를 측정하고 plain-orifice, chamfered-orifice 및 venturi 형상 인젝터의 유동 특성을 분석하였다. Plain-orifice 및 chamfered-orifice 인젝터의 경우 하류방향으로 유동이 진행할수록 점도가 높아지는 특성이 나타났으며 Venturi 형상의 경우 인젝터 내부 유동에서 낮은 점도가 지속적으로 유지됨을 알 수 있었다. Reynolds 수가 증가할수록 이러한 경향이 뚜렷하게 나타나는 것이 확인되었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.438-444
• /
• 2010

Crossflow에 미치는 영향을 최소화하면서 liquid Jet의 미립화 및 혼합특성을 향상시키기 위한 JICF의 분무 특성에 대해 실험적으로 연구하였다. Crossflow의 온도, 속도, 압력과 liquid Jet의 속도, 압력을 변화시키면서 crossflow와 liquid jet의 momentum ratio(q)의 변화에 따른 spray boundary (outer boundary, inner boundary)를 측정하고 실험식을 유도하여 선행연구자의 결과와 비교하였다. 특히, injector의 형상에 따른 jet penetration를 측정하여 dual orifice injector의 경우 전단 오리피스의 영향으로 후단 오리피스에서의 jet penetration은 single orifice injector 분사노즐과 비교할 때 약 18% ($L_h$=4 mm) 증가하는 것을 확인하였다.

• 한국분무공학회지
• /
• 제6권2호
• /
• pp.9-15
• /
• 2001

The internal flow characteristics of a gasoline direct injector have been studied to improve fuel economy and reduce exhaust emissions. Computational Fluid Dynamics (CFD) is used to examine the internal flow of the GDI with the purpose of designing the optimum geometry of the injector. This study tests orifice length, cone angle, swirl angle, orifice diameter and needle lift. The results show that optimum sizes of the orifice length, cone angle, swirl angle, orifice diameter and needle lift are 0.8mm, $140^{\circ},\;120^{\circ},\;80mm\;and\;70{\mu}m$, respectively. The size of the lift does not affect the formation of the air core signficantly near the tip of the needle compared to the ball-type needle. The vena contracta phenomenon near the orifice inlet can be released by smoothing the edge.

• International Journal of Aeronautical and Space Sciences
• /
• 제12권1호
• /
• pp.57-62
• /
• 2011

The effects of swirl chamber's diameter and length on injector's dynamic characteristics were investigated through an experimental study. A mechanical pulsator was installed in front of the manifold of a swirl injector which produces pressure oscillations in the feed line. Pressure in the manifold, liquid film thickness in the orifice and the pressure in the orifice were measured in order to understand the dynamic characteristic of the simplex swirl injector with varying geometry. A direct pressure measuring method (DPMM) was used to calculate the axial velocity of the propellant in the orifice and the mass flow rate through the orifice. These measured and calculated values were analyzed to observe the amplitude and phase differences between the input value in the manifold and the output values in the orifice. As a result, a phase-amplitude diagram was obtained which exhibits the injector's response to certain pressure fluctuation inputs. The mass flow rate was calculated by the DPMM and measured directly through the actual injection. The effect of mean manifold pressure change was insignificant with the frequency range of manifold pressure oscillation used in this experiment. Mass flow rate was measured with the variation of injector's geometries and amplitude of the mass flow rate was observed with geometry and pulsation frequency variation. It was confirmed that the swirl chamber diameter and length affect an injector's dynamic characteristics. Furthermore, the direction of geometry change for achieving dynamic stability in the injector was suggested.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.179-188
• /
• 2003

The spray characteristics of dual orifice injector were investigated under two different fuels through measurement of SMD, number density and volume flux by using PDPA system. In this experiment, we found out that the droplet size and spray structure are strongly depend on fuel density and viscosity.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.218-225
• /
• 2008

When the heat release and acoustic pressure fluctuations are generated in the combustor by irregular combustion, these fluctuations affect the mass flow rate of the propellants injected through the injectors. Also, the variations of the mass flow rate by these fluctuations again bring about irregular combustion and furthermore that is related with combustion instability. Therefore, it is very important to identify the mass variation for the pressure fluctuation on the injector and to investigate its transfer function. So, we first have studied quantifying the variation of mass flow rate generated in simplex swirl injector by injection pressure fluctuation. To acquire the transient mass flow rate in orifice with time, we have tried to measure of the flow axial velocity and liquid film thickness in orifice. The axial velocity is acquired through theoretical approach after measuring the pressure in orifice and the flow area in the orifice is measured by electric conductance method. As results, mass flow rate calculated by axial velocity and liquid film thickness measuring in orifice accorded with mass flow rate acquired by direct measuring method in the small error range within 1 percents in steady state and within 6 percents as average mass flow rate in pulsated state. Hence this method can be used to measure the mass flow rate not only in steady state but also in unsteady state because the mass flow rate in the orifice can acquire with time and this method shows very high accuracy based on the experimental results.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.251-255
• /
• 2005

본 연구에서는 스월 인젝터의 기하학적 형상에 따른 분무특성 파악을 위해 액막두께 측정방법을 사용하였다. 액막두께 측정을 위해 특별히 제작된 인젝터를 사용하였으며, 백홀과 스월챔버 그리고 오리피스의 길이에 따른 분무특성을 확인하였다. 분무특성 파악을 위해 분사압에 따른 유량변화, 오리피스 하단의 액막두께와 분무각을 측정하였다.

• 한국분무공학회지
• /
• 제7권4호
• /
• pp.32-41
• /
• 2002

The breakup characteristics of liquid sheets formed by like-doublet injector were investigated in the cold-flow and atmospheric ambient pressure condition. The sheet breakup wavelength, which induces the sheet to be broken into ligaments, as well as the sheet breakup length, which is important for the flame location, was measured using a stroboscopic light. The liquid ligaments are formed intermittently after the breakup of sheet, and the wavelength of ligaments has been believed to have a relation to the combustion instability of liquid rocket engine. Therefore, the wavelength of ligaments and the breakup length of ligaments into fine drops were also measured. Since these spray characteristics are affected by the flow characteristics of two liquid jets before they impinge on each other, we focused on the effects of orifice internal flow such as the cavitation phenomenon that occurs inside the sharp-edged orifice. From the experimental results, we found that the liquid jet turbulence delays the sheet breakup and makes shorter wavelengths for both sheets and ligaments. Since the turbulent strength of sharp-edged orifice is stronger than that of round-edged orifice, the shape of orifice entrance results in large differences in the spray characteristics. Using these results, we proposed empirical models on the spray characteristics of the like-doublet injector, and these models are believed to provide some useful and actual data for designing liquid rocket combustors.