• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1562-1564
• /
• 2003

In this study, PZT thin films were fabricated using sol-gel processing onto Si/$SiO_2$/Ti/Pt substrates. PZT sol with different Zr/Ti ratio(20/80, 30/70, 40/60, 52/48) were prepared, respectively. The films were fabricated by using the spin-coating method on substrates. The films were heat treated at $450^{\circ}C,\;650^{\circ}C$ by rapid thermal annealing(RTA). The preferred orientation of the PZT thin films were observed by X-ray diffraction(XRD), and Scanning electron microscopy(SEM). All of the resulting PZT thin films were crystallized with perovskite phase. The fine crystallinity of the films were fabricated. Also, we found that the ferroelectric properties from the dielectric constant of the PZT thin films were over 600 degrees, P-E hysteresis constant. And the leakage current densities of films were lower than $10^{-8}A/cm^2$. It is concluded that the PZT thin films by sol-gel process to be convinced of application for ferroelectric memory device.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.6
• /
• pp.401-415
• /
• 2021

Soft robots are promising devices for applications in drug delivery, sensing, and manufacturing. Traditional hard robotics are manufactured with rigid materials and their degrees of motion are constrained by the orientation of the joints. In contrast to rigid counterpart, soft robotics, employing soft and stretchable materials that easily deforms in shape, can realize complex motions (i.e., locomotion, swimming, and grappling) with a simple structure, and easily adapt to dynamic environment. Among them, the magnetic actuators exhibit unique characteristics such as rapid and accurate motion control, biocompatibility, and facile remote controllability, which make them promising candidates for the next-generation soft robots. Especially, the magnetic actuators instantly response to the stimuli, and show no-hysteresis during the recovery process, essential for continuous motion control. Here, we present the state-of-the-art fabrication process of magnetically controllable nano-/micro-composites, magnetically aligning process of the composites, and 1-dimensional/multi-dimensional multimodal motion control for the nextgeneration soft actuators.

• Journal of Distribution Science
• /
• v.20 no.7
• /
• pp.73-86
• /
• 2022

Purpose: Considering the COVID-19 pandemic and the increasing number of online food delivery applications (OFDA), this study aims to assess the distribution of the presence of Indonesian OFDA and to measure the factors that influence the spending habits of OFDA users. Research design, data and methodology: Two hundred and nine OFDA users from Jakarta's Generation Z were surveyed via a questionnaire. The data were analyzed using Structural Equation Modeling and SMART PLS 3.0. Results: OFDAs were introduced into Indonesia in the recent past with varying degrees of popularity determined by the number of downloads. Users' intention to use was not determined by the speed of the introduction of an OFDA. This study also reveals that previous experience of the service, the orientation of time and price savings had a significant effect on spending habits. A moderating role of the saving variable on time and price was not demonstrated. Conclusions: The results of the study suggest that, in COVID-19 pandemic conditions, the spending habits of Generation Z are not based on impulse, thrift, or extravagance. The pandemic shaped specific motivations in spending habits, namely prioritizing need. This study has limitations, including the small sample size and the use of internal variables.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.4
• /
• pp.16-23
• /
• 2021

Currently, 6-axis articulated robots are used throughout the industry because of their 6-dof (degrees of freedom) and usability. However, 6-axis articulated robots have a fixed base and their movements are limited by the rotational operating range of each axis. If the angle of the 2-axis additional axes can be adjusted according to the position and orientation of the end-effector of the 6-axis articulated robot, the effectiveness of the 6-axis articulated robot can be further increased in areas where the angle is important, such as welding. Therefore, in this paper, we proposed a cooperative kinematic inter-operation strategy. The strategy will be verified using the Simulink of MATLABⓇ, an engineering program, and RecurdynⓇ, a dynamic simulation program.

• New & Renewable Energy
• /
• v.19 no.4
• /
• pp.84-97
• /
• 2023

This study aimed to investigate the feasibility and potential applications of utilizing bifacial photovoltaic (PV) panels from an architectural perspective. It also aimed to establish a foundational dataset for installation and operational guidelines for bifacial PV panels through a comparative analysis of energy production performance with single PV panels. The research encompassed several key steps, including a comprehensive literature review, calculation of solar surface radiation values, development of datasets for bifacial and single PV energy production, and a performance comparison between both approaches. The results of the study show that bifacial PV panels exhibit optimized energy production capabilities within the range of 40 to 80 degrees, contingent upon the specific installation location. Consequently, it is recommended that the installation of bifacial PV panels in Korea should primarily focus on southwest-to-west orientation. Furthermore, it was concluded that bifacial PV panels could contribute an equivalent or even superior level of energy production compared to single PV panels, even if their performance exhibited a marginally lower efficiency of 2% to 5% with an 18% power generation efficiency.

• Computers and Concrete
• /
• v.34 no.1
• /
• pp.15-31
• /
• 2024

This study explores the failure mechanisms of 'I' shaped non-persistent cracks under uniaxial loads through a combination of experimental tests and numerical simulations. Concrete specimens measuring 200 mm×200 mm×50 mm were manufactured, featuring 'I' shaped non-persistent joints. The number of these joints varied from one to three, with angles set at 0, 30, 60, and 90 degrees. Twelve configurations, differing in the placement of pre-existing joints, were considered, where larger joints measured 80 mm in length and smaller cracks persisted for 20 mm with a 1 mm crack opening. Numerical models were developed for the 12 specimens, and loading in Y-axis direction was 0.05 mm/min, considering a concrete tensile strength of 5 MPa. Results reveal that crack starting was primarily influenced by the slope of joint that lacks persistence in relation to the loading direction and the number of joints. The compressive strength of the samples exhibited variations based on joint layout and failure mode. The study reveals a correlation between the failure behavior of joints and the number of induced tensile fracture, which increased with higher joint angles. Specimen strength increased with decreasing joint angles and numbers. The strength and failure processes exhibited similarities in both laboratory testing and numerical modeling methods.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.23-30
• /
• 2017

Most superconducting magnets which generate more than 20 T consist of nested magnets. A combination of LTS and HTS magnets is conventionally used, but high field magnets which use only HTS magnets have been developed recently. As HTS wires have very strong magnetic anisotropy, appropriate techniques should be used to consider this effect properly. The load line method has been conventionally used to design nested magnets for high field generation. Because this method considers only parallel and perpendicular magnetic fields, the effect of their orientation is not taken into account. In this paper, the actual orientation of the magnetic fields from 0 to 90 degrees is considered. The critical currents of the two kinds of high field nested magnets designed using the proposed method are calculated. The finite element method is used to calculate the distribution of the magnetic fields and the evolution strategy is used to find the critical current which maximizes the central magnetic field.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.481-487
• /
• 2019

Additive manufacturing is a state-of-the-art manufacturing process technology in which three-dimensional structures are fabricated by laminating two-dimensional sections of a structure using various materials such as plastic, ceramics, and metals. The additive manufacturing technology has the advantage of high design freedom, while the surface property (roughness) of the finished product varies depending on the process conditions, which necessitates performing a post-process after the products are manufactured. In this study, the surface roughness of a structure made of polyamide 12, which was manufactured by SLS (Selective Laser Sintering) and MJF (Multi Jet Fusion) process was compared. The processing condition was classified by the building orientation of structure as 0, 45, and 90 degrees, which is the angle between the analytical surface and the horizontal plane of the fabrication platform. Structures with a hole of various diameters ranging from 1mm to 10mm were manufactured and the hole characteristics (ratio of hole depth to diameter) and results of the specimens were compared. As a result of the surface characteristics analysis, the surface roughness value of the specimens manufactured with a building orientation of $45^{\circ}$ was the highest in both technologies. In the case of the through-hole structure fabrication, the shape was maintained with 5mm and 10mm diameter holes regardless of the building orientation, although the hole forming was difficult for the smaller holes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.10
• /
• pp.983-989
• /
• 2017

This paper presents the bearing strength for laminates in advanced composite materials in bolted joints. Bolted single lap joint tests were experimentally investigated with respect to stabilized and unstabilized lap joints. Stabilized bolted single lap joints refer to joints with out-of-plane rotational constraints. Unstabilized bolted single lap joints refer to joints with absence of out-of-plane deflection constraints. The bearing strength values of laminates in the bolted joint showed that the percentages of ply angle for 0, 45, -45, and 90 degrees were not affected. The bearing strength value in the unstabilized bolted joint was smaller than the bearing strength value in the stabilized bolted joint because of the influence of the out-of-plane behavior. The composite material studied in this paper is a carbon/epoxy unidirectional (UD) tape prepreg cured at $177^{\circ}C(350^{\circ}F)$. In the laminate reference system, the standard angles of 0, 45, -45, and 90 degrees were used for ply orientation within the laminate. A total of 112 bolted single lap joint tests were conducted on specimens from eight distinct laminates. The ASTM-D-5961M standards were adhered to for the stabilized and unstabilized bolted single lap joint tests.

• Cartoon and Animation Studies
• /
• s.25
• /
• pp.203-225
• /
• 2011

This study investigated hypothesized relationships between three personality traits, as defined by PEN model (Psychoticism, Extraversion and Neuroticism), and individual media dependency. The basic idea of the study was that individuals' goals are related to active media use, and the goals will be different based on differences in individuals' personality types. In addition, this study attempted to find whether there are gender difference in constructing media dependency relations with the media. The study was conducted online and the total number of participants was 337 (158 male and 179 female). Correlation analyses indicated no relationship between the extraversion and any of the IMD media use categories. Lower levels of psychoticism were related to a greater likelihood of utilizing the media in an effort to obtain self understanding and having fun more than higher levels of psychoticism. Individuals with higher levels of neuroticism were significantly more likely to depend on the media for achieving self understanding than those with lower levels of neuroticism. When the variable of participant gender was controlled for, there were different patterns of the relationships between personality types and IMD goals. This study showed that to varying degrees certain personality types are related to the goals individuals seek to fulfill with the media use. The implications of the study were discussed.