• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.395-398
• /
• 2000

Reactive radio frequency (RF)magnetron sputter with incident angle has been used to deposit AlN thin film on a crystalline Si substrate. (002)Preferred orientation of AlN thin film has been obtained at low sputtering pressure. Also it has been shown that depostion rate of AIN thin film is affected by fraction Ar and $N_2$ partial pressure. But substrate temperature didn't affect depostion rate of AIN thin film . As sputtering pressure increased preferred orientation degraded. The internal stress changed from tensile stress to compressive stress as fraction of $N_2$ partial pressure increased. At low nitrogen partial pressure cermet$^{[1]}$ AIN thin film is obtained.

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.619-624
• /
• 2021

Vehicle orientation detection is a challenging task because the orientations of vehicles can vary in a wide range in captured images. The existing methods for oriented vehicle detection require too much computation time to be applied to a real-time system. We propose Rotate YOLO, which has a set of anchor boxes with multiple scales, ratios, and angles to predict bounding boxes. For estimating the orientation angle, we applied angle-related IoU with CIoU loss to solve the underivable problem from the calculation of SkewIoU. Evaluation results on three public datasets DLR Munich, VEDAI and UCAS-AOD demonstrate the efficiency of our approach.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.21 no.1
• /
• pp.75-81
• /
• 1985

The tensile and dielctric strength of the epoxied resin with bi-directional woven glass fibers with a laminate of two layers(G-10) are studied, and the test parameter is the angle between fiber orientation and the tensile axis. The obtained results may be summaried as follows: 1) when the angle between fiber orientation and tensile axis was varied from 0$^{\circ}$ to 45$^{\circ}$ the yield and fracture stresses have a tendency to decrease with increase in the angle. Especially, the decrease rates in the yield and fracture stresses are changed remarkably in the range of 0$^{\circ}$ to 15$^{\circ}$. 2) The fracture strain has showed the maximum value when the angle between fiber orientation and tensile axis is 45$^{\circ}$, and showed the rapid rate of change from 15$^{\circ}$ to 45$^{\circ}$. 3) For the sample with same angle between fiber orientation and tensile axis the maximum dielectric strength under compressive stress is decreased with increase in tensile stress, when the compressive stress is increased as a parameter of tensile stress. 4) When the angle between fiber orientation and tensile axis is 45$^{\circ}$, the dielectric strength showed the worst value, as the mechanical strength did.

• KIEAE Journal
• /
• v.17 no.4
• /
• pp.75-81
• /
• 2017

Purpose: Most contemporary office buildings supply external views, a sense of openness and a sense of time to their occupants by adopting the curtain walls, which are equipped with an outer cover having large window area. As a result, the amount of radiation increases, adversely affecting cooling load during the summer in office buildings. Although solar radiation decreases heating load and reduces energy costs during the winter period, due to the characteristics of offices where occupants work largely during daytime, the cooling load is important compared to the heating. Therefore, diverse measures to resolve those trade-offs and annual energy cost have been investigated. Method: In this study, the annual thermal load was comparatively analyzed according to the slat angle of the venetian blind along with lighting control technique. Result: After selecting effective conditions, in order to resolve such issues, this study established automated control strategies of slat angle depending on the window-to-wall ratio and zone orientation, so that the findings of this study can be effectively generalized to other circumstances.

• Journal of the Korean Academy of Clinical Electrophysiology
• /
• v.10 no.2
• /
• pp.23-29
• /
• 2012

Purpose : Purpose of this study was to investigate whether cervicothoracic posture was associated with scapula orientation and muscle activity during shoulder abduction. Methods : Cervicothoracic junction angle and thoracic kyphosis angle were measured in health twenty subjects. Then, scapular resting orientation and range of motion (upward/downward rotation, internal/external rotation) and muscle activity (upper trapezius, lower trapezius, serratus anterior) was determined using motion capture system and surface electromyography while subjects performed shoulder abduction. Results : Cervicothoracic junction angle was significantly associated with range of motion of scapular internal/external rotation during shoulder abduction. Thoracic kyphosis angle was significantly associated with scapular resting orientation of upward/downward rotation and average IEMG of lower trapezius. Conclusion : The result of this study shows that poor cervicothoracic posture is relationship with altered scapular kinematics cause of shoulder dysfunction. These findings suggested that cervicothoracic posture may be considered in occupation and exercise including arm elevation over head as well as used as predict factor to estimate shoulder dysfunction.

• Journal of Korean Neurosurgical Society
• /
• v.56 no.5
• /
• pp.400-404
• /
• 2014

Objective : Clip artifacts limit the visualization of intracranial structures in CT scans from patients after aneurysmal clipping with cobalt alloy clips. This study is to analyze the parameters influencing the degree of clip artifacts. Methods : Postoperative CT scans of 60 patients with straight cobalt alloy-clipped aneurysms were analyzed for the maximal diameter of white artifacts and the angle and number of streak artifacts in axial images, and the maximal diameter of artifacts in three-dimensional (3-D) volume-rendered images. The correlation coefficient (CC) was determined between each clip artifact type and the clip blade length and clip orientation to the CT scan (angle a, lateral clip inclination in axial images; angle b, clip gradient to scan plane in lateral scout images). Results : Angle b correlated negatively with white artifacts (r=-0.589, p<0.001) and positively with the angle (r=0.636, p<0.001) and number (r=0.505, p<0.001) of streak artifacts. Artifacts in 3-D images correlated with clip blade length (r=0.454, p=0.004). Multiple linear regression analysis revealed that angle b was the major parameter influencing white artifacts and the angle and number of streak artifacts in axial images (p<0.001), whereas clip blade length was a major factor in 3-D images (p=0.034). Conclusion : Use of a clip orientation perpendicular to the scan gantry angle decreased the amount of white artifacts and allowed better visualization of the clip site.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.3
• /
• pp.372-380
• /
• 2003

Impact tests were conducted to study the effect of angle ply and metal laminate on impact damage characteristics of Fiber Metal laminates (FML). Impact tests were conducted using drop weight impact machine and damage behavior were analyzed by comparing with load-displacement curve and surface observation and microscopic observation of cross sections. The effect of angle ply on impact characteristics of FML are influenced by property of metal laminate. i.e., when the metal laminate is not enough to strong to prevent fiber debonding, Angle ply FML is superior to singly oriented ply (SOP) FML because angle ply enhance the stiffness by fiber supports and prevent (rack propagation. However, when the metal laminate is enough to strong to prevent fiber debonding, SOP FML is superior to Angle ply FML because the fiber of lower ply in Angle ply FML are more stressed than that of SOP FML.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.119-130
• /
• 1999

This paper deals buckling behavior of laminated composite cylindrical shells subjected to combination of axial compression and torison. Linear and nonlinear finite element analysis are carried out . the influence of load type, load ratio, fiber orientation angle, stacking sequence, and intial imperfect on buckling behavior is discussed.

• Journal of Industrial Technology
• /
• v.11
• /
• pp.65-72
• /
• 1991

In this paper, a control algorithm is discussed when the quadruped walking robot walks over the unknown soft ground. Firstly, it estimated the relationship between the foot force and the ground sinkage at the leg-placing phase. Secondly, the generated soil property is applied to the leg-supporting phase. If the attitude angle is changed by incorrect ground sinkage compensation, the control algorithm adjusts the attitude angle using simplified orientation orientation matrix.

• Steel and Composite Structures
• /
• v.11 no.5
• /
• pp.359-374
• /
• 2011

In this paper, the influence of fibre orientation and aspect ratio on stability analysis of simply supported skew plates subjected to in plane loading is studied by using a four noded hybrid plate finite element. The formulation of the element is based on Hellinger-Reissner variational principle. The element is developed by combining a hybrid plane stress element and a hybrid plate element. Some numerical problems are solved and the effects of skew angle, aspect ratio, fibre orientation and loading type on the critical buckling loads are highlighted.