• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.84-87
• /
• 2010

Copper-indium-diselenide (CIS) particles were prepared by the electrochemical reduction from the mixture solution of corresponding ion compounds. The prepared CIS was used as an insertion layer or a blending component in the organic photovoltaic bulk heterojunction cells composed of poly(3-octylthiophene) and fullerene. The increase of CIS content resulted in the rapid decrease of the open-circuit voltage as well as short-circuit current. The photovoltaic parameters were analyzed in relation to the structures, composition, and morphology of the photovoltaic blends.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.112-115
• /
• 2004

Photovoltaic effects in $CuPc/C_{60}$ heterojunction structure have been studied depending on thickness of exciton blocking layer(BCP) and electrodes. Bare ITO and polymer coated electrode(PEDOT:PSS) were used as an anode, and Al, Ca/Al, Mg/Al, LiF/Al, and LiAl were used as a cathode. Photovoltaic parameters depending on BCP layer thickness from 0 to 60 nm and electrodes having different work function were measured using Keithley 236 source-measure unit and a 500W xenon lamp (ORIEL 66021). We have seen that the BCP layer thickness severely affects on the performance of photovoltaic cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.08a
• /
• pp.185-185
• /
• 2008

• Proceedings of the Korean Society of Potoscience Conference
• /
• 2005.06a
• /
• pp.84-84
• /
• 2005

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.181-181
• /
• 2013

Recently, nanostructure and the molecular orientation of organic thin films have been largely paid attention due to its importance in organic electronics such as organic thin film transistors (OTFTs), organic light emitting diodes (OLEDs), and organic photovoltaics (OPVs). Among various methods, the diffraction and scattering techniques based on synchrotron x-rays have shown powerful results in organic thin film systems. In this work, we introduce the in-situ annealing system installed at PLS-II (Pohang Light Source II) for organic thin films by simultaneously conducting various x-ray scattering measurements of x-ray reflectivity, conventional x-ray scattering, grazing incidence wide angle x-ray scattering (GI-WAXS) and so on. Using the in-situ measurement, we could obtain real time variation of nanostructure as well as molecular orientation during thermal annealing in metal-phthalocyanine thin films. The variation of surface and interface also could be simultaneously investigated by the x-ray reflectivity measurement.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.11
• /
• pp.975-979
• /
• 2014

Transparent conductive films (TCF) with excellent electrical properties and high mechanical flexibility have been widely studied because of their potential for application in optoelectronic devices such as light-emitting diodes, paper displays and organic solar cells. In this paper, we report on low-resistance and high-transparent TCF for flexible device applications. To fabricate a high-resolution roll imprinted TCF, the following steps were performed: the design and manufacture of an electroforming stamp mold, the fabrication of high-resolution roll imprinted on flexible film, the manufacture of Ag-nano paste which was filled into patterned film using a doctor blade process. Also, we was demonstrated with the successful application(ITO free organic photovoltaic) of the developed flexible TCF.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1714-1715
• /
• 2011

In this work, highly conductive organic solvent-based polyaniline(PANI) was used as an anode in organic photovoltaic cells (OPV) based on poly - (3-hexylthiophene) and [6,6] - phenyl - C60 - butyricacid methyl ester (P3HT : PCBM). The transmittance of the used PANI film were 87.67% and 86.57% at 550nm, and its sheet resistance were 454 ${\Omega}/{\Box}$ and 298 ${\Omega}/{\Box}$. We fabricated ITO-free OPV cells using PANI as an anode, which exhibited an external power conversion efficiency of 2.28% with a result of Jsc of 6.922mA/cm2, Voc of 0.6093V, and FF of 54.10% under an illumination of air mass(AM) 1.5G (100mW/$cm^2$). We used ink-jet printing to deposit buffer layer and active layer on a glass substrate.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.353-356
• /
• 2014

We fabricated organic photovoltaic (OPV) based on ZnO ripple structure on indium tin oxide as electron-collecting layers and PTB7-F20 as donor polymer. In addition, atomic layer deposition (ALD) was used for preparing additional ZnO layers on rippled ZnO. Addition of 2 nm-thick ALD-ZnO resulted in enhanced initial OPV performance and stability. Based on photoluminescence results, we suggest that ALD-ZnO layers reduced number of surface defect sites on ZnO, which can act as electron-hole recombination center of OPV, and increased resistance of ZnO towards surface defect formation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.116.1-116.1
• /
• 2011

Materials with a combination of high electrical conductivity and optical transparency are important components of many electronic and optoelectronic devices such as liquid crystal displays, solar cells, and light emitting diodes. In this study, to fabricate a low-resistance and high optical transparent electrode film for organic photovoltaic, the following steps were performed: the design and manufacture of an electroforming stamp mold, the fabrication of thermal roll imprinted (TRI) poly-carbonate (PC) patterned films, the manufacture of high-conductivity and low-resistance Ag paste which was filled into patterned PC film using a doctor blade process and then coated with a thin film layer of conductive polymer by a spin coating process. As a result of these imprinting processes the PC films obtained a line width of $10{\pm}0.5{\mu}m$, a channel length of $500{\pm}2{\mu}m$, and a pattern depth of $7.34{\pm}0.5{\mu}m$. After the Ag paste was used to fill part of the patterned film with conductive polymer coating, the following parameters were obtained: a sheet resistance of $9.65{\Omega}$/sq, optical transparency values were 83.69 % at a wavelength of 550 nm.

• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.654-659
• /
• 2010

We have investigated the effect of rubrene-doped CuPc hole transport layer on the performance of p-i-n type bulk hetero-junction photovoltaic device with a structure of ITO/PEDOT:PSS/CuPc: rubrene/CuPc:C60(blending ratio 1:1)/C60/BCP/Al and have evaluated the current density-voltage(J-V) characteristics, short-circuit current($J_{sc}$), open-circuit voltage($V_{oc}$), fill factor(FF), and energy conversion efficiency(${\eta}_e$) of the device. By rubrene doping into CuPc hole transport layer, absorption intensity in absorption spectra decreased. However, the performance of p-i-n organic type bulk hetero-junction photovoltaic device fabricated with crystalline rubrene-doped CuPc was improved since rubrene shows higher bandgap and hole mobility compared to CuPc. Increased injection currents have effected on the performance improvement of the present device with energy conversion efficiency(${\eta}_e$) of 1.41%, which is still lower value compared to silicone solar cell and many efforts should be made to improve organic photovoltaic devices.