• Journal of the Korean institute of surface engineering
• /
• v.1 no.1
• /
• pp.5-13
• /
• 1967

Up to this date, numerous methods of analysis of electropling solutions are published. Some, however, need lots of works before reaching final results, or require high technique and special instruments, and also some are unaccurate due to unclearnes of end point. Like our undevelop countries, technicians of electroplating shops are most high school graduates or under, and have not much knowledge on chemistry. Furthermore, those technicians have to control their plating solutions by themselves without having enough analytical laboratory equipment . Therefore, in this paper the simplest, besides accurate method is investigated after comparing numerous methods published. Among the methods of copper determinations from acid and alkaline copper plating baths, EDTA titration method are chosen, due to these methods are the simpest and fastest for the evaluation of metal content, without requirng any special instrument. For acid copper solutions, chelate titrations were accurate enough. Since the end point of titration of chelate method is variable according to the kind of indicators and other metal's coexisitence as well as solution component, many difficulties were encountered from cyanide copper, on the contrary of acid copper bath. PAN , PV, and MX indicators were tried , but it is found that MX is the best. In chyanide solution ,due to cyanide is the masking reagent , elimination of this component is essential , and finally found that elimination CN-by precipitation with AgNO$_3$ solution was the simplest and the most accurate way among others. This method was very accurate for the new plating solutions even coexistence with organic brightners. However used solutions for long months running have to be predetermined the accurate copper value by thiosulfate method form time to time, before chelate titration by means of AgNO$_3$ precipitation. Always some constant deviations will be seen according to the solutions nature. Therefore those deviation values have to be compensated each time.

• Journal of Environmental Impact Assessment
• /
• v.7 no.2
• /
• pp.5-14
• /
• 1998

This study was performed to estimate interrelation between characteristics of sediment and nutrient releare from sediment in Dae-cheong lake. For the investigations, sediments were sampled in June and October 1997 at fish farms, embayment, and the main stream of Dae-cheong lake. Items for investigation are as follows; water content, weight loss on ignition(IG), porosity of sediment, Total Kjeldahl Nitrogen(TKN), content of element(H, N, C), nutrient release rate. Water content and porosity were measured to conjecture the physical trait and grain size. And weight loss on ignition was measured to determine the contents of organic substance. For the determination of nutrient release rate, $PO_4-P$ and $NH_4-N$ concentration of interstitial water and overlying water were measured. Release rate of nutrients which has direct influenced upon the water quality were 0.05-8.63mg-$P/m^2{\cdot}day$ and 4.99-36.56mg-$N/m^2{\cdot}day$. And it was found that release rate was measured higher in the 1st sampling than in the 2nd sampling. And for determination of the humus level of sediment, carbon and nitrogen content were measured by using elemental analyzer. Generally, C/N ratio is used to determine humus level of lake sediment. As a result of elemental analysis, C/N ratio was determined in the range of 7.64~11.55, so humus level of Dae-cheong lake sediment was estimated from mesohumic state to oligohumic state.

• Proceedings of the Korean Society of Applied Pharmacology
• /
• 2004.04a
• /
• pp.3-10
• /
• 2004

Oxidative stress is a constant threat to all living organisms and an immense repertoire of cellular defense systems is being employed by most pro- and eukaryotic systems to eliminate or to attenuate oxidative stress. Ischemia and reperfusion is characterized by both a significant oxidative stress and characteristic changes in the antioxidant defense. Heme oxigenase-l (HO-l) is up-regulated by various stimuli including oxidative stress so that it is thought to participate in general cellular defense mechanisms against ischemic injury in mammalian cells. Higenamine, an active ingredient of Aconite tuber, has been shown to have antioxidant activity along with inhibitory action of inducible nitric oxide synthase (iNOS) expression in various cells. In the present study, we investigated whether higenamine and related analogs protect cells from oxidative cellular injuries by modulating antioxidant enzymes, such as HO-l, MnSOD etc. R-form of YS-51 was the most potent inducer of HO-l in bovine endothelial cells, which inhibited apoptotic cell death by H$_2$O$_2$. HO-1 induction by YS 51 was mediated by PI3 kinase activation in which PKA- as well as PKG pathway is considered as important regulators. YS-51 also induced Mn-SOD mRNA expression by activating c-jun N-terminal kinase in endothelial cells and Hela cells. In ROS 17/2.1 cells, higenamine and enetiomers of related compounds inhibited iNOS expression by cytokine mixtures. Taken together, higenamine and related compounds can be developed as possible protective agents from oxidative cell injury or death.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.132-132
• /
• 1998

Ion bombardment in the keV range is known to induce drastic chemical modifications in organic and inoranic molecular comppounds. A degrading effects in orgainc materials such as the release of ppolymer compponents and the chemistry of the iradiation pprocess have been observed. The work to be described was carried out in order to understand the irradiation effect better. The sampple(ppolyimide : Kappton ) Were irradiated by Ar+, Ne+, H+ ions and electrons (3 keV) to fluence ranging from ~1$\times$1015 to ~1$\times$1017 ions/$cm^2$ at room tempperature. The impplant was usually rastered over an area of a few $cm^2$ . These ion impplantation were carried out in an electron sppectrometer ESCA 5700 (ppHI Ltd) at a residual gas ppressure of ~5$\times$10-10 Torr. X-ray pphotoelectron sppectroscoppy(XppS) measurements were made using a monochromatized Al Kａ(1486.6 eV) excitation source. The pphotoemitted electrons were detected by hemisppherical analyser with a ppass energy of 23.5 eV. Core-level binding energies were referenced to the Fermi level. To avoid the charging effect it was used the neutralizer. We studied the irradiation effects on ppolyimide with Ar+, Ne+, He+ ions and electrons by XppS which 추 pprovide detailed information concerning the bonding-induced changes.

• Journal of Korean Society on Water Environment
• /
• v.28 no.6
• /
• pp.917-922
• /
• 2012

In order to improve applicability of a microbial fuel cell the laboratory-scaled study has been performed by adopting an air-cathode MFC system with high concentrated anaerobic slugies in this study. The concentrations of microbes are grouped into three types, Type A (TS 1.7%), Type B (TS 1.1%) and Type C (TS 0.51%). The open circuit voltage $(V_{oc})$ characteristics showed that the medium microbes concentration of 1.10% (Type B) kept a constant voltage of 1.0 V for 150 hours, which showed the longest time among three types (Type A and Type C). The discharge charge curves for a closed circuit with $500 \Omega$ also showed that Type B generated a stable discharge voltage of 0.8 V for a longer time as in the open circuit voltage case. This could be explained by the relatively large amount of the attached microbes. Under the $V_{oc}$condition the COD removal efficiency of Type B was found to be low for a long time, but those of Type A and C were found to be high for a short period of time. Therefore, the suspended microbes could decrease the coulombic efficiency. It was concluded that the high $V_{oc}$ was caused by low COD and the $V_{oc}$ became low after the COD removal. The COD reduction resulted in an unstable and low working voltage. From the polarization characteristics Type A was found to show the highest power density of $193\;mW/m^2$ with a fill factor of 0.127 due to the relatively high remaining COD even after the MFC reaction.

• Journal of Korean Society on Water Environment
• /
• v.25 no.4
• /
• pp.522-529
• /
• 2009

To supply safe drinking water to areas lacking in water supply and drainage system, such as rural area and military bases in proximity to Demilitarized Zone, effective method for treating organic contaminants such as MTBE is required. This study focuses on seeking optimal conditions for effective degradation of MTBE using a bath type ultrasound reactor. Effectiveness of MTBE degradation by ultrasound is dependent on the frequency, power, temperature, treatment volume, initial concentration, catalyst, etc. In this study the degradation rate of MTBE by ultrasound was proportional to power/unit volume ratio and removal is relatively more efficient for 0.1 mM than for 1 mM of MTBE solution. Efficiency of ultrasound treatment for 1 mM MTBE solution was enhanced under bath temperature of $30^{\circ}C$ compared to $4^{\circ}C$, but the temperature effect was negligible for 0.1 mM MTBE solution. Also for 0.1 mM MTBE solution, effect of catalyst such as $TiO_2$ and $Fe^0$ on treatment speed was negligible, and zeolite even increases the time taken for the degradation. Under these specific experimental conditions of this study, the most determinant factor for degradation rate of MTBE in solution was frequency and power of ultrasound. The results have shown that a continuous ultrasound reactor system can be used for small scale remediation of organically polluted groundwater, under optimal conditions.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.505-505
• /
• 2011

The control of wettability of thin films is of great importance and its success surely brings us huge applications such as self-cleaning, antifogging and bio-passive treatments. Usually, the control is accomplished by modifying either surface energy or surface topography of films. In general, hydrophobic surface can be produced by coating low surface energy materials such as fluoropolymer or by increasing surface roughness. In contrast, to enhance the hydrophillicity of solid surfaces, high surface energy and smoothness are required. Silica (SiO2) is environmentally safe, harmless to human body and excellently inert to most chemicals. Also its chemical composition is made up of the most abundant elements on the earth's crest, which means that SiO2 is inherently economical in synthesis. Moreover, modification in chemistry of SiO2 into various inorganic-organic hybrid materials and synthesis of films are easily undertaken with the sol-gel process. The contact angle of water on a flat silica surface on which the Young's equation operates shows ~50o. This is a slightly hydrophilic surface. Many attempts have been made to enhance hydrophilicity of silica surfaces. In recent years, superhydrophilic and antireflective coatings of silica were fabricated from silica nanoparticles and polyelectrolytes via a layer-by-layer assembly and postcalcination treatment. This coating layer has a high transmittance value of 97.1% and a short water spread time to flat of <0.5 s, indicating that both antireflective and superhydrophilic functions were realized on the silica surfaces. In this study, we assessed hydrophillicity and hydrophobicity of silica coating layers that were synthesized using the sol-gel process. Systematic changes of processing parameters greatly influence their surface properties.

• Analytical Science and Technology
• /
• v.11 no.3
• /
• pp.222-228
• /
• 1998

Five kinds of packed column and two kinds of capillary column were used to get optimum condition for ethanol analysis by using fifteen different volatile, low molecular weight organic substances. Only two columns, Gaskuropack 54 and DB-1, showed good separation efficiency. In the adding salt-effect experiment 0.6N - perchloric acid, 1M - meta-phosphoric acid and saturated NaCl solution were used for alcohol concentration measurement of biological fluids and tissue specimens. Among adding salt experiment, adding saturated NaCl solution showed the most stable value of alcohol concentration. This fact might be due to the increased vaporization of alcohol in the saturated NaCl solution. In the time-course of blood alcohol concentration, the alcohol level was lineary decreased to the diameter of vessel containing specimens. This result was interpreted in view of ethanol level, weight, water content, and hematocrit value. The ethanol distribution levels were measured from samples of blood and tissue obtained from 25 postmortems cases investigated by NISI. This study showed that the distribution level was decreased in order of brain, blood, kidney, spleen, liver, and lung.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.4
• /
• pp.272-278
• /
• 2001

To investigate of C and N metabolisms in response to phosphorus-deficient stress during regrowth of Italian ryegrass (Lolium multiflorum L.), C and N metabolites were analyzed at 0, 6, 12 and 24 days after defoliation. P-sufficient (control, +P) and P-absent (-P) nutrient solutions were applied from 7 days before defoliation, and continued for one cycle of 24 day-regrowth period. During 24 days of regrowth, dry matter of regrowing shoots and remaining tissues were not significantly different between +P and -P treatment. In remaining stubble, 70% to 91 % decline of the initial level (at day 0) in all C compounds occurred during the first 6 days of regrowth. Initial amounts of nitrate and amino acids in roots were significantly higher in the +P medium. Nitrate contents in stubble in the +P medium significantly decreased for the first 12 days and then rapidly recovered, while that of the -P medium continuously decreased until day 24. Amino acids in stubble in the P medium were continuously increased during the whole regrowth period. Soluble proteins in stubble in the +P medium also largely fell down (46.0% of the initial) for only the first 6 days, however the decline in the -P medium continued until day 12. In regrowing shoots, the accumulation of C compounds was significantly higher, while that of N compounds except amino acids was largely lower in the -P medium. These results showed a stimulation of carbohydrate synthesis and a compensatory utilization of organic reserves occurred to support regrowth under P-deficient condition.

• Atmosphere
• /
• v.28 no.2
• /
• pp.211-222
• /
• 2018

Cloud droplet activation process is well described by $K{\ddot{o}}hler$ theory and several parameterizations based on $K{\ddot{o}}hler$ theory are used in a wide range of models to represent this process. Here, we test the two different method of calculating the solute effect in the $K{\ddot{o}}hler$ equation, i.e., osmotic coefficient method (OSM) and ${\kappa}-K{\ddot{o}}hler$ method (KK). To do that, each method is implemented in the cloud droplet activation parameterization module of WRF-CHEM (Weather Research and Forecasting model coupled with Chemistry) model. It is assumed that aerosols are composed of five major components (i.e., sulfate, organic matter, black carbon, mineral dust, and sea salt). Both methods calculate similar representative hygroscopicity parameter values of 0.2~0.3 over the land, and 0.6~0.7 over the ocean, which are close to estimated values in previous studies. Simulated precipitation, and meteorological variables (i.e., specific heat and temperature) show good agreement with reanalysis. Spatial patterns of precipitation and liquid water path from model results and satellite data show similarity in general, but on regional scale spatial patterns and intensity show some discrepancy. However, meteorological variables, precipitation, and liquid water path do not show significant differences between OSM and KK simulations. So we suggest that the relatively simple KK method can be a good alternative to the OSM method that requires various information of density, molecular weight and dissociation number of each individual species in calculating the solute effect.