• 한국미생물·생명공학회지
• /
• 제19권4호
• /
• pp.377-382
• /
• 1991

우지를 lipase에 의해 지방산과 글리세린으로 분해하는 반응을 액상 및 고상에서 수행하였다. 올리브유를 기질고 lipase OF 360(일본 메이토사 제품)의 특성을 조사한 결과 최적 pH는 6, 최적 온도는 $37^{\circ}C$이었다. 우지를 기질로 액상 효소반응을 수행한 결과는 물사용량 80 wt/wt, 온도 $37^{\circ}C$, 효소사용량 200unit/g tallow 조건에서 93의 가수분해율을 얻을 수 있었다.

• 한국의류산업학회지
• /
• 제14권3호
• /
• pp.472-477
• /
• 2012

The conditions of wet spinning were considered in order to prepare the fine denier of acrylic fiber. Polyacrylonitrile copolymer was synthesized by the copolymerization of acrylonitrile (AN) and methyl acrylate (MA) initiated by an aqueous sulfite-chlorate redox system. Acrylic fiber was manufactured through wet-spinning in a dimethyl formamide (DMF) system. The conditions of wet-spinning were investigated by i-value, spinning speed, diameter of spinneret, draw ratio, water content of spinning dope and morphology of protofiber. The physical properties of fibers were investigated by Instron. In this experiment, the minimum i-value decreased with the decreasing spinneret diameter, an increased spinning speed, and an increased coagulation bath (CBC) concentration. The maximum draw ratio increased with an increased CBC. The optimum CBC and water content of the spinning dope were 60%-65% and 3.5%, respectively. The tenacity at the breaking point increased with a decreased fineness of fiber. The elongation at breaking point was almost the same value as a function of the fineness of fiber.

• 한국식품영양과학회지
• /
• 제32권3호
• /
• pp.388-392
• /
• 2003

콩분말을 질소원으로 첨가하여 타피오카의 무증자 알콜발효에 미치는 영향을 조사하였다. 생콩분말 첨가가 볶음콩분말 첨가 보다 알콜함량이 전반적으로 높게 나타났으며, 콩분말 농도별 첨가에 따른 영향은 생콩분말 첨가의 경우 2%까지는 증가하다가 3% 이후로 감소하는 경향을 나타내었으며, 볶음콩 분말의 경우 첨가농도에 따른 알콜함량은 큰 차이를 나타내지 않았다. pH와 총산은 생콩분말 ,볶음콩분말의 첨가, 가수량과 효소제 첨가에 따른 영향을 거의 받지 않는 것으로 나타났다. 생콩분말 2%(w/w), 가수량 250%(v/w), 효소제 0.5%(w/w)를 사용하여 3$0^{\circ}C$, 96시간 발효하였을 때 알콜 함량이 가장 높은 것으로 나타나 콩분말을 이용하여 타피오카의 무증자 알콜발효 조건을 설정 할 수 있었다. 콩분말 첨가는 타피오카의 무증자 알콜발효에서 알콜수율을 증가시켰다.

• 한국식품조리과학회지
• /
• 제7권1호
• /
• pp.27-34
• /
• 1991

This study attempted to set up reasonable extraction time of Omija that was put in water for the various components to soak out. Changes of free sugars, organic acids, reducing sugar, total acid and tannin in Omija with various extraction times were investigated (together with the analysis of each components in Omija fruit). 1. High Performance Liquid Chromatography showed fructose, glucose, and sucrose to be the major free sugars of the Omija fruit. Free sugars and reducing sugar value in Omija beverage increased gradually in according with the extraction time, and marked 75.6% per total free sugars and 82.1% per total reducing sugar at 12 hours. 2. Gas Chromatography showed lactic acid, oxalic acid, fumaric acid, levulinic acid, succinic acid, malic acid, citric acid and pyroglutamic acid to be the major organic acids of the Omija fruit. Organic acids and total acids value in Omija beverage increased gradually on proportion to extraction time, and marked 97.0% per total organic acids at 9 hours and 79.0% per total acids at 12 hours. 3. Tannin content in Omija beverage was increased when extraction time was longer but it showed a low percentage as compared with the reducing sugar and total acid. Tannin content marked 48.8% per total tannin at 12 hours. 4. Sensory evaluation revealed that !1 hours of extraction produced the best quality products based in taste, flavor, color and over-all acceptability, considering the data, it seems possible to conclude that the optimum of time for extraction of Omija to water is 9 hours.

• 한국농공학회지
• /
• 제25권4호
• /
• pp.69-79
• /
• 1983

The objective of this study is to analyze the present situation of compaction equipment used in the earth fill dam construction, and the compaction effects of varions types of equipment on core and pervious zones of the fill dam. The results obtained are summarized as follows; 1. Banking materials mostly used for the core zone were soils classified as CL, SC and ML, while those classified as SM, ML and SC were predominant for the pervious zone. 2. Equipments used practically in the real fields were considerably different from those specified in the designs. 3. It was found that the relationship between optimum water content and maximum dry density for both core and pervious materials showed to be linear, ranging from 10% to 25% water content. That is, ${\gamma}$dmax (core) = 2.2555-0.0284 Wopt ${\gamma}$dmax(pervious) =2.239-0.028 Wopt 4. The generalized compaction guides for all kinds of equipment and soil types consi- dered in this study may be recommended as N=8-10 T=2Ocm, N=10-12 T=3Ocm for core zone(98%) and N=6-8 T=2Ocm, N=8-10 T=3Ocm for pervious zone (95%). 5. The coefficient of permeability in the field tests showed abont 10 times as high as the laboratory test value. This large deviation, however, was due to the horizontal permeation and considered not to be significant in the light of the satisfactory compaction ratio in the field compac- tion.

• Nuclear Engineering and Technology
• /
• 제45권1호
• /
• pp.61-66
• /
• 2013

Among the radioactive wastes generated from the nuclear power plant, a radioactive nuclide such as $^{129}I$ is classified as a difficult-to-measure (DTM) nuclide, owing to its low specific activity. Therefore, the establishment of an analytical procedure, including a chemical separation for $^{129}I$ as a representative DTM, becomes essential. In this report, the adsorption and recovery rate were measured by adding $^{125}I$ as a radio-isotopic tracer ($t_{1/2}$ = 60.14 d) to the simulation sample, in order to measure the activity concentration of $^{129}I$ in a pressurized-water reactor primary coolant. The optimum condition for the maximum recovery yield of iodine on the anion exchange resins (AG1 x2, 50-100 mesh, $Cl^-$ form) was found to be at pH 7. In this report, the effect of the boron content in a pressurized-water reactor primary coolant on the separation process of $^{129}I$ was examined, as was the effect of $^3H$ on the measurement of the activity of iodine. As a result, no influence of the boron content and of the simultaneous $^3H$ presence was found with activity concentrations of $^3H$ lower than 50 Bq/mL, and with a boron concentration of less than 2,000 ${\mu}g/mL$.

• 대한환경공학회지
• /
• 제36권10호
• /
• pp.679-684
• /
• 2014

가축전염병 확산을 방지하기 위하여 조성된 긴급매몰지의 경우 침출수 누출이 확인되면 원형저장조로 이설된 경우가 있는데, 저장조 내 낮은 함수율과 혼합문제로 인해 분해가 거의 이루어지지 않고 있는 실정이다. 본 연구에서는 사체의 안정화를 촉진할 수 있도록 원형저장조를 생물반응조(Bioreactor)로 구조를 변경하였다. 침출수를 재순환하고 미생물을 공급하여 안정화에 필요한 미생물활동을 증가시켰다. 원형저장조 내부 유기물의 변형을 고려한 침하량 모형을 사용하여 예측한 침하량 최종치는 생물저장조 구조 변경 후 5년간 약 30%이었다.

• 상하수도학회지
• /
• 제13권1호
• /
• pp.43-50
• /
• 1999

In spite of low energy requirement, and operation and construction cost, biofilters with soil beds have not been operated efficiently. Because of excess moisture in winter and rainy periods, saturated pores in the bed prevent passage and sorption of odorous compounds. Sometimes this results in septic conditions that release previously sorbed and oxidized sulfur. Therefore, an economical and effective alternative needs to be developed. The objectives of this study were to confirm applicability of the granular scrap tires with compost for treating odorous gas as well as to obtain optimum design parameters for proposed system. In lab-scaled test, multiple stage reactors had lower headloss than a single stage reactor and less headloss was occurred for the gas with higher moisture content. For practical purpose, pilot-scaled reactor was operated to remove odor from septic tank, manure and animal wastewater treatment plant and composting machine. According to the results of pilot scaled test, $H_2S$ can be always removed completely and ammonia/amine can be removed excellently when proper moisture content is provided. The results from lab and pilot test showed that granular scrap tire could be replaced with soil as supporting material for biofilter showed excellent drainage because of its ability to reject moisture.

• 한국식품영양학회지
• /
• 제6권4호
• /
• pp.294-300
• /
• 1993

This study was carried out to investigate the influences of cultural conditions of koji on the production of saccharogenic amylase during rice-koji making by Aspergillus awamori var. kawachii which is now widely used as koji-mold in brewing Tikju and Yakju in Korea. The optimum cultural temperature for the production of saccharogenic amylase by this mold was 36$^{\circ}C$, and at this temperature it needed 40 hours of cultivation for maximum production of this enzyme. It was favorable for high production of both organic acid and saccharogenic amylase to shift the cultural temperature form initial 36$^{\circ}C$ to 32$^{\circ}C$ after 20~25 hours of cultivation. The production of saccharogenic amylase was low when the water content of steamed rice was below 35%, but its production was high at 40~60% of water content. When the quantity of conidial inoculation was too small, the production of saccharogenic amylase was low in initial phase, but it was retrived after 40 hours of cultivation. When koji-thickness was over 3cm, the production of saccharogenic amylase was markedly restricted. The saccharogenic amylase of this koji was stable at pH 2~7, and showed high activity at pH 2~5.

• 한국재료학회지
• /
• 제28권12호
• /
• pp.685-690
• /
• 2018

In this study, a multifunctional ophthalmic lens material with an electromagnetic shielding effect, high oxygen permeability, and high water content is tested, and its applicability is evaluated. Metal oxide nanoparticles are applied to the ophthalmic lens material for vision correction to shield harmful electromagnetic waves; the pyridine group is used to improve the antibacterial effect; and silicone substituted with urethane and acrylate is employed to increase the oxygen permeability and water content. In addition, multifunctional tinted ophthalmic lens materials are studied using lens materials with an excellent antibacterial effect (2,6-difluoropyridine, 2-fluoro-4-pyridinecarboxylic acid) and functional (UV protection, high wettability) lens materials (2,4-dihydroxy benzophenone, 2-hydroxy-4-(methacryloyloxy)benzophenone). To solve problems such as air bubbles generated during the polymerization process for the manufacturing and turbidity of the lens surface, polymerization conditions in which the defect rate is minimized are determined. The results show that the polymerization temperature and time are most appropriate when they are $110^{\circ}C$ and 40 minutes, respectively. The optimum injection amount of the polymerization solution is 350 ms. The turbid phenomenon that appears in lens processing is improved by 10 to 95 % according to the test time and conditions.