• Composites Research
• /
• 제29권1호
• /
• pp.7-15
• /
• 2016

고분자 재료로 된 자동차부품들은 주로 사출성형으로 제작되며, 이 과정에서 뒤틀림, 침전 흔적, 용입선, 수축, 잔류응력 등의 결함이 발생한다. 본 연구를 통해서 이들 결함을 제거할 수 있는 차량용 폴리카보네이트 버튼의 사출성형 공정변수를 실험계획법을 이용하여 최적화 하였다. 공정변수로는 충전압력, 금형온도, 용융온도, 충전시간을 고려했으며 FEM, 다구치법, ANOVA를 사용하여 해석하고 최적화 하였다. 최적화 결과, 충전압력은 140 MPa, 금형온도는 $105^{\circ}C$, 용융온도는 $292.5^{\circ}C$, 충전시간은 1초, 등의 공정변수 값을 얻었으며, 10.2의 S/N 비를 얻었다. 수지의 용융온도가 가장 큰 영향을 미치며, 그 다음으로 금형의 온도였다.

• 소성∙가공
• /
• 제8권3호
• /
• pp.276-283
• /
• 1999

This study focuses on part quality and cycle times under gas-assisted injection molding (GIM) of box shape molded parts. The position of the gas channel was established near to parting line at the end of last locations to fill. Applied hot runner and valve gates, the gas was introduced directly into the mold cavity via gas pin. As GIM was applied, the conclusion reached as follows. I) The quality of appearance was improved by reducing sink marks and scratches of texture. ii) The reliability was improved by preventing warpages and reinforcing rigidity through optimum gas channel layout. iii) It is enable to use small size of injection molding machine step by step as GIM was accomplished low pressure and reduced clamp forces against CIM. iv) The productivity were improved by reducing cycle times.

• 한국금형공학회:학술대회논문집
• /
• 한국금형공학회 2008년도 하계 학술대회
• /
• pp.175-181
• /
• 2008

The technologies of mold design, manufacturing, injection molding process and computer aided engineering(CAE) are developed rapidly with the growth of plastic product market. Injection molding process optimum design can not be easily determined. This study was determined factors and levels which carried out to analyze an influence of narrow pitch BGA socket warpage and performed investigating the main effect and interaction effect between factors using design of experiment. The result of this paper is injection time and packing pressure are affect on narrow pitch BGA socket warpage at injection molding.

• 한국산학기술학회논문지
• /
• 제12권9호
• /
• pp.4223-4238
• /
• 2011

최근 환경에 대한 관심이 증대되면서 지반보강 재료의 친환경성이 강조되며, 이에 따라 각종 지반주입 재료가 개발되고 있으나 건설현장에서는 대부분 물유리계 재료가 활용되고 있다. 또한 최근 선진국에서는 물유리계 지반 주입재의 단점인 내구성 문제를 해결하기 위하여 여러 가지 공법을 개발하고 있는 실정이다. 본 연구에서는 기존 그라우트 재료의 문제점을 향상시키기 위하여 친환경적인 무기계 가소성그라우팅 재료에 대한 실내 시험을 통해 그라우팅 재료의 공학적 특성을 파악하고자 하였다. 실내시험에서는 그라우팅 재료의 사용량에 따른 점성, 가소성, 압축강도 및 환경영향평가에 대한 검토를 수행하여 최적 배합에 대한 범위를 설정하고, 설정된 배합의 현장적용을 통해 기존의 그라우팅 재료보다 경제적, 공학적으로 우수한 그라우트 재료에 대하여 평가하고자 한다.

• 한국수소및신에너지학회논문집
• /
• 제31권3호
• /
• pp.307-313
• /
• 2020

The 3.9 liter diesel engine with a mechanical fuel injection system was converted to di-methyl ether (DME) engine and performance optimized. In order to switch to the DME engine, the plunger of the high pressure fuel pump was replaced and the diameter of the injector nozzle was increased. Through this, the disadvantage of DME having low calorific value per volume can be compensated. To optimize the performance, the number of injector nozzle holes, injector opening pressure, and fuel injection timing were changed. As a result, the optimum number of injector nozzle holes was 5, the injector opening pressure was from 15 MPa to 18 MPa, and the injection timing was 15 crank angle degree before top dead center (CAD BTDC). The power was at the same level as the base diesel engine and nitrogen oxides (NOx) emissions could be reduced.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.271-278
• /
• 1987

본 논문에서는 공기밸브형 진동연소기에 관한 이해를 더 증진시키기 위해서 기본적인 공기밸브형 진동연소기를 제작해서 압력진동 및 발생되는 소음특성, 작동주 파수, 그리고 연소특성에 관해 실험적 고찰을 행했다.

• Journal of Biosystems Engineering
• /
• 제35권3호
• /
• pp.163-168
• /
• 2010

With income growth and "well-being" trends, sales of corn has been increased recently. Corns are processed at processing facilities on the main production site. Corn processing steps include removing bract, steaming, vacuum packing, and storing. To replace manual corn bract removing, some bract removing machines were imported and used. However, the machines were abandoned shortly, because of high damaging ratio of corns. In this research, factors of successful bract removing was studied with rotating rollers and air-injection nozzles to develop corn bract removing system. The test device was composed of a cylindrical roller, an air spray nozzle, a regulator, and a motor. Designing factors were roller type, diameter of air spraying nozzle, spraying angle, and spraying pressure. The measured factors were bract removing rate and damaging rate. It was found that optimum cylindrical roller surface shape was cylindrical roller and linear grove roller. This roller shape produced lowest damaging rate. Test results of the efficacy of preprocessing showed that the air spraying after preprocessing produced highest performance. The rotational speed and inclination of the roller didn't affect the bract removing performance. Optimum injection angle of the air jet nozzle was $70^{\circ}$. To increase bract removing rate and to reduce corn damage, required injection pressure and injection nozzle diameter were decided to less than 0.4 MPa and 2.5 mm, respectively. More than 3 times of nozzle passing produced good bract removing performance and there were no significant difference between the number of passing times.

• 한국식품과학회지
• /
• 제29권5호
• /
• pp.947-954
• /
• 1997

옥수수가루에 건조유제품을 첨가하여 탄산가스의 주입에 의해 반죽의 온도 $100^{\circ}C$ 이하에서 팽화시킨 몇 가지 제품의 물리적 성질과 기계적 에너지 투입량을 분석하였다. 첨가된 유제품은 전지분유, 유청단백질 농축물, 탈지분유, 카제인 나트륨이며, 첨가량은 옥수수가루의 무게비로 10%와 20%를 각각 첨가시켰다. 압출성형기 바렐로 주입되는 가스압력을 0.7 MPa과 1.4 MPa로 조절하여 옥수수가루를 팽화시켰다. 시스템변수인 비기계적 에너지 투입량은 지방의 함량이 높은 전지분유의 첨가량이 증가할수록 감소하였다. 또한 카제인 나트륨의 첨가에 의한 비기계적 에너지의 투입량의 감소도 적었다. 압출성형물의 밀도는 주입압력 0.7 MPa까지는 점차적으로 감소하다가 그 이상의 압력에서는 증가하였다. 가스주입압력 0.7 MPa에서 유제품의 함량이 0, 10, 20%로 증가할수록 밀도는 증가하는 경향을 보였으며, 카제인 나트륨을 첨가했을 때 밀도가 증가하는 정도가 가장 낮았다. 가스주입압력이 0.7 MPa까지 팽화율은 증가하다가 그 이상의 주입압력에서는 감소했지만, 비길이는 계속 증가하는 경향을 나타내었다. 수분흡착지수는 유제품의 첨가에 의해 감소하는 경향을 나타내었고, 반면에 수분용해지수는 증가하는 경향을 보였다. 본 압출성형시스템을 이용한 유제품을 첨가한 옥수수가루 압출성형물 제조시 최적 가스주입압력은 0.7 MPa이였으며, 전지분유의 첨가는 제한인자가 되었으나, 카제인 나트륨의 첨가에 의하여 유제품의 첨가량을 높일 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.350-353
• /
• 2001

Due to the widen demand of plastic part in automobiles, more accurate numerical simulation works are needed to find optimum molding process like filling fiber orientation pressure control. Therefore, C-mold software was applied for the simulation of injection molding process and cooling process in this research. The purpose of this study is developing a ball seat which made by injection process with PA66 resin and it is applied to the automobile suspension system. It must secure low friction, wear resistance and dimensional accuracy. Specially this study aims to get the quality stabilization of injection molded bass-seat parts.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.131.2-135
• /
• 1999

This study focuses on part quality and cycle times under gas-assisted injection molding(GIM) of housing molded parts. The position of the gas channel was estabished near to parting line at the end of last locations to fill. Applied hot runner and valve gates the gas was introduced directly into the mold cavity via gas pin. As GIM was applied the introduced directly into the mold cavity via gas pin. As GIM was applied the conclusion reached as follows. I) The quality of appearance was improved by reducing sink marks and scratches of texture ii) The realibility was improved by preventing warpages and reinforcing rigidity through optimum gas channel layout iii)It is enable to use small size of injection molding machine step by step as GIM was accomplished low pressure and reduced clamp forces against CIM iv)The productivity were improved by reducing cycle times.