• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.3
• /
• pp.518-523
• /
• 1998

The fracture toughness and hardness of 62 %$SiO_2-19%ZrO_2-9%Na_2O-10%B_2O_3$(wt%) glass ceramics system were investigated. As a result of DTA study to find crystallization temperature, an exothermic peak near $820^{\circ}C$ was observed. The optimum nucleation temperature and the optimum crystal growth temperature were determined by XRD and SEM analysis, and were approximately $650^{\circ}C$, $840^{\circ}C$ respectively. The fracture toughness of this zirconia glass ceramics was determined by Vickers Indentation Method. The hardness value was not changed with increasing of the heat treatment temperature, but fracture toughness value was increased up to $1.8 MPa{\cdot}m^{1/2}$ at $840^{\circ}C$, with increasing of heat treatment temperature.

• Journal of Biosystems Engineering
• /
• v.20 no.3
• /
• pp.250-261
• /
• 1995

This study has been performed to develop an agricultural waste incinerator to combust the rice hull originated from RPC with the typical disposal treatment capacity of 30kg/h and to test performance of the developed incinerator. Experimental results are summarized as following. 1. The optimum feed rate of rice hull of the incinerator is 30kg/h with air ratio of 1.5. 2. The contents of $SO_2$ in flue gas is maximum 18ppm(when rice hull feed rate was 20kg/h and air ratio of 1.5), minimum 7ppm(when rice hull feed rate was 30kg/h and air ratio of 1.5) and average 11ppm. So there is no environmental pollution problem for the incinerating treatment of rice hull of the RPC. 3. The temperature of water of heat exchanger are $53^{circ} C$ and $62^{circ} C$ with water flow rate $3{ell}/min$ and $1.5{ell}/min$ at the optimum combustion condition, respectively. 4. According to theoretical energy calculation, the energy from rice hull combustion may be amounted as much as 80%~190% of energy supplied by kerosene required by RPC.

• Journal of Korea Foundry Society
• /
• v.11 no.4
• /
• pp.331-337
• /
• 1991

Various test specimens were prepared by austempering low alloyed Mo-Ni-Cu ductile iron blocks of high graphite nodule count at 270, 320 or $370^{\circ}C$ for 0.5, 1, 3 or 9hrs. Tensile test, CVN impact test and plane-strain fracture toughness test(compact tension specimen of 50mm W) were done for each heat treatment condition at room temperature. X-ray diffractometer and optical microscope were used to investigate the change of microstructure and relationships between microstructure and test results. The highest retained austenite volume percent at each austempering temperature was corresponded to the highest mechanical property. The highest elongation value of 17%, U.T.S. value of 1,600 MPa or $K_{IC}$ value of 90MPa${\surd}$m were reached at each optimum condition. The best heat treatment condition for fracture toughness were 3hrs' holding time combined with the austempering temperature of 270 and $320^{\circ}C$, and 1hr's of $370^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.29 no.5
• /
• pp.396-402
• /
• 1992

Carbon solid was prepared from dormant mesophase pitch (DMPP) without using a binder and its properties were characterized. DMPP powder was stabilized with air or nitric acid in pretreatment stage so that it might not soften in later heat ttreatment stage. Optimum sintering properties were obtained from carbon powder with 2.36∼2.38 of C/H atomic ratio and 1.27∼1.40 of C/O atomic ration in air stabilization. In nitric acid stabilization, optimum sintering properties were obtained when 20∼40 vol.% of nitric acid solution was used. Compressive strength increased up to 1200$^{\circ}C$ of heat treatment temperature, and the highest compressive strength and bulk density of carbon solid from DMPP were 3000 kgf/㎤, respectively. The optical properties of carbon solid obtained was fine mosaic structure. Carbon solid after graphitization showed the properties of hard carbon due to stabilization and its shore hardness was 120.

• Journal of Powder Materials
• /
• v.25 no.4
• /
• pp.340-345
• /
• 2018

Additive manufacturing by electron beam melting is an affordable process for fabricating near net shaped parts of titanium and its alloys. 3D additive-manufactured parts have various kinds of voids, lack of fusion, etc., and they may affect crack initiation and propagation. Post process is necessary to eliminate or minimize these defects. Hot isostatic pressing (HIP) is the main method, which is expensive. The objective of this paper is to achieve an optimum and simple post heat treatment process without the HIP process. Various post heat treatments are conducted for the 3D-printed Ti-6Al-4V specimen below and above the beta transus temperature ($996^{\circ}C$). The as-fabricated EBM Ti-6Al-4V alloy has an ${\alpha}^{\prime}$-martensite structure and transforms into the ${\alpha}+{\beta}$ duplex phase during the post heat treatment. The fatigue strength of the as-fabricated specimen is 400 MPa. The post heat treatment at $1000^{\circ}C/30min/AC$ increases the fatigue strength to 420 MPa. By post heat treatment, the interior pore size and the pore volume fraction are reduced and this can increase the fatigue limit.

• Korean Journal of Materials Research
• /
• v.11 no.11
• /
• pp.965-971
• /
• 2001

The objective of this study is to investigate the characteristics - microstructure, hardness, adhesive strength and friction coefficient - of the coatings with aging - treatment after optimizing internal- plasma spraying parameters for Al-30wt%Si powder as a basic research to manufacture the cylinder block bore for Al engine composed of Al-30wt%Si alloy on Al alloy, The optimum internal-plasma spraying parameters of Al-30wt%Si alloy are summarized as follows: voltage: 37.5V, current: 160A, working distance: 25mm, gun traverse speed: 4.5mm/s, rotating speed: 518m/min. The primary Si particles grew aggressively with increasing heat-treating temperature. The hardness of the as-sprayed coating was about Hv=275 but this value was abruptly decreased with increasing heat-treating temperature. And average friction coefficient of the coating was below 0.08 after heat treatment for 48h at $175^{\circ}C$.

• Korean Journal of Food Science and Technology
• /
• v.46 no.5
• /
• pp.588-592
• /
• 2014

Under optimized condition mild pressure in combination with specific temperature for heat treatment transform the 6-gingerol into 6-shogaol. The purpose of this study was to optimize the conditions used for heat treatment under pressure for increasing 6-shogaol content in ginger (Zingiber officinale Roscoe). A central composite experimental design was used to evaluate the effects of application temperature ($70-130^{\circ}C$) and temperature-holding time (95-265 min) on the transformation of 6-shogaol. The experimental values were shown to be in significantly good agreement with the predicted values (adjusted determination coefficient, $R^2{_{Adj}}=0.9857$). 6-Shogaol content increased as the application temperature and temperature-holding time increased. By analyzing the response surface plots, the optimum conditions of heat treatment (temperature and time) for increasing 6-shogaol content were found to be $127^{\circ}C$ and 109 min, respectively. Under these optimal conditions, the predicted 6-shogaol content was 3.98 mg/g dried ginger. The adequacy of the model equation for predicting the optimum response values was effectively verified by the validation data.

• Journal of the Korean Society for Heat Treatment
• /
• v.12 no.2
• /
• pp.108-116
• /
• 1999

Gray cast iron with a high damping capacity has been used for controlling the vibration and noise in various mechanical structures. Nevertheless, its usage has been often restricted due to its poor tensile strength. Therefore, it is necessary to improve tensile strength at the expense of a loss in damping capacity. This study is aimed at finding the best combination of tensile strength and damping capacity by varying austempering time and temperature range from $320^{\circ}C$ to $380^{\circ}C$ after austenization at $900^{\circ}C$ for 1hr. The effect of austempering condition on hardness and the volume fraction of retained austenite is investigated as well. The results obtained are summarized as follows : (1) With an increase in austempering temperature, both tensile strength and hardness decrease while damping capacity improves. (2) Austempering at $350^{\circ}C$, resulting in a mixture of upper and lower bainite with partially retained austenite, exhibits the optimum combination of tensile strength and damping capacity.

• Journal of the Korean Ceramic Society
• /
• v.28 no.5
• /
• pp.406-414
• /
• 1991

The composition of base glass was selected as MgO 8, Al2O3 24, SiO2 68 in weight percent. TiO2 and ZrO2 were added to the base glass to investigate their effects as nucleating agents. In the case of ZrO2 addition, the optimum temperature for nucleation, which was related to the precipitation of tetragonal ZrO2, was 80$0^{\circ}C$. The optimum growth condition for the crystal was 87$0^{\circ}C$ for 8 hrs, and the major crystal phases precipitated in the samples were $\beta$-quartz ss. and mullite. The light transmissivity turned out to be around 80 per cent. On the other hand, when the TiO2 was added, it was difficult to determine the nucleating temperature, because the samples turned easily into translucency during the heat treatment. Therefore, it was almost impossible to retain transparency in the samples. The light transmissivity was below 30 per cent.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.388-391
• /
• 1999

Well oriented Bi2212 superconductor thick films were formed successfully on a copper substrate by liquid reaction between a Cu-free precursor and Cu tape method in which Cu-free BSCO powder mixture was' printed on copper plate and heat-treated. And we examined the effect of heat-treatment atmosphere for the superconducting properties and microstructure of Bi2212. The composition of Cu-free BSCO powder mixture was Bi$_2O_3$ : SrCO$_3$ : CaCO$_3$ = 1.2~2 : 1 : 1 and the heat-treatment for the superconducting formation reaction was performed in air, oxygen, nitrogen and low oxygen pressure. At heat-treatment temperature, the printing layer partially melt by reacting with CuO of the oxidizing copper plate, and the nonsuperconducting phases present in the melt are typically Bi-free phases and Cu-free phases. Among the nonsuperconducting phases, it is known that the (Sr,Ca)CuO$_3$ phase restrain the formation of the Bi2212 superconducting phase. Because a kind of the nonsuperconducting phases is controled by the oxygen partial pressure, the optimum condition in which the remnants of the second phases don't leave in the fully processed conductor was determined by XRD and the critical tempera to re (Tc) analysis.