• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.3
• /
• pp.15-21
• /
• 2012

The optimum dewaxing ratio in dewaxing treatment by the heat and pressure method was investigated by considering aging stability of dewaxed Hanji. Commercial Hanji was coated with beeswax and thermally aged at $150^{\circ}C$ for 24 hours. Then it was dewaxed using the laboratory sheet press equipped with hot plates on both top and bottom sides. Dewaxing ratio was controlled by pressing temperature and time. Four type of dewaxed Hanji samples with different dewaxing ratio were prepared and thermally aged at $150^{\circ}C$. Then the aging stability of dewaxed Hanji samples was evaluated in terms of optical and strength properties. It was found that the aging stability of dewaxed Hanji was superior with higher dewaxing ratio. The result concluded that, in the aspect of aging stability, the coated beeswax in beeswax-treated Hanji shall be completely removed if the coated wax would be dewaxed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.6
• /
• pp.272-277
• /
• 2010

The glass-ceramics containing bottom ash (B/A) which was a by-produced from an electrical power plant was fabricated and its crystalline phase, microstructure and mechanical properties were analyzed. At first, the glass was fabricated by adding modifier oxide $Li_2O$ to lower the melting temperature of coal bottom ash. The glass obtained was heat-treated by using a 2-stage process to crystallize, that is to say, to increase the degree of crystallization in the glass-ceramics, the first heat treatment for nucleation was performed followed by the secondary one for the growth of nucleates. The main crystalline phase formed in the glass-ceramics was ${\beta}$-spodumene and the secondary phase was $L_2SiO_3$. It was recognized that the degree of crystallization of glass-ceramics was increased with a holding time of the secondary heat treatment stage. In the case of the specimens hold up to 3 hour, the crystallization was not completed and the microstructures and morphologies of crystalline phase were not uniform. In the specimens of holding time over 9 hours, the cracks were generated inside of it, so its compressive strength would decrease due them. In conclusion, it was able to obtain the optimum condition to fabriate the glass-ceramics having the properties of high crystallization degree, uniform microstructures and morphologies and the high mechanical strength.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.2
• /
• pp.105-110
• /
• 2000

The $\alpha$-$Fa_{2}O_{3}/SnO_{2}$ thin film gas sensor was fabricated by APCVD and heat treated. The gas sensitivity to flammable gases ($CH_4$, $H_2$, LPG) was measured. This device was to heat treatment at $400^{\circ}C$, $450^{\circ}C$, $500^{\circ}C$, $550^{\circ}C$, $600^{\circ}C$ for 2 h to enhance the gas sensitivity. The heat treated device at $500^{\circ}C$ for 2 h had the best properties and especially it shows high sensitivity to H2 gas. The sensitivity to gases was studied in the temperature range from lOoC to $300^{\circ}C$ in order to find the optimum detection temperature. In the range of detection from 500 ppm to 10,000 ppm at $175^{\circ}C$ the fabricated device showed that the gas sensitivity to $H_2$ was from 62%~76% and to $CH_4$ was from 16 %~58% and to LPG was from 8%~37 %. The sensitivity difference between heat treated device and as fabricated one was about 10 8 The long-term stability to LPG at 1,000 ppm was converged to sensitivity of 30 %.

• Food Engineering Progress
• /
• v.15 no.4
• /
• pp.398-403
• /
• 2011

A dielectric barrier discharge plasma (DBDP) treatment system was fabricated and the optimum operating conditions for the plasma generation were determined in order to explore the potential of cold plasma as a non-thermal proessing technology. The microbial inactivation performance of the system was also evaluated against Staphyloocus aureus. The system consisted of power supply, transformer, electrode assembly and sample treatment plate. The input power was 220 V single phase AC and amplified to 10.0-50.0 kV on a transformer. A pulsed sine wave of frequency 10.0-50.0 kHz was introduced to the electrode embedded in ceramic as a dielectric barrier material in order to generate plasma at atmospheric pressure. Higher currents and consequently greater power were required for the plasma generation as the frequencies increased. A homogeneous and stable plasma was generated at currents of 1.0-2.0, and frequencies of 32.0-35.3 kHz. The optimum electrode-gaps for the plasma generation were 1.85 mm without loaded samples. More power was consumed as the electrode-gaps increased. The practically optimum electrode- gap was, however, 2.65 mm when samples were treated on slide-glasses for microbial inactivation. The maximum temperature increase after 10 min treatment was less than 20$^{\circ}C$, indicating no microbial inactivation effect by heat and thereby insuring a non-thermal method. The DBDP inactivation effect against Staphyloocus aureus increased linearly with treatment time up to 5 min, but plateaued afterward. More than 5 log reduction was achieved by 10 min treatment at 1.25 A.

• Korean Journal of Materials Research
• /
• v.12 no.11
• /
• pp.870-874
• /
• 2002

$Mg_2$$SiO_4$: Dy, Tb pellets were made by using a sintering process, including pressing and heat treatment. In the present study, the optimum parameters of the sintering for the $Mg_2$$SiO_4$: Dy, Tb pellets obtained such as the pressing pressure, the sintering temperature and the sintering time were in terms of thermoluminescence. Experimental results showed that the main peak of the glow curve for $Mg_2$$SiO_4$: Dy, Tb thermoluminescence dosimeter was clearly correlated with the energy of the UV and with the grain size. The intensity of the TL glow curve increased and its main peak position shifted to lower temperature with increasing UV irradiation time.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1268-1269
• /
• 2008

$CuInS_2$ thin films were fabricated by sulpurization of Cu/In Stacked elemental layer deposited onto glass substrates by vacuum annealing at various temperatures. And structural and electrical properties were measured in order to certify optimum conditions for growth of the ternary compound semiconductor $CuInS_2$ thin films by composition ratio. Physical properties of the thin film were investigated at various fabrication conditions; substrate temperature, annealing temperature and annealing time by XRD, FE-SEM and hall measurement system. $CuInS_2$ thin film was well made at the heat treatment 200[$^{\circ}C$] of SLG/Cu/In/S stacked elemental layer.

• Journal of Magnetics
• /
• v.22 no.2
• /
• pp.169-174
• /
• 2017

In this work, lithium ferrite ($Li_{0.5}Fe_{2.5}O_4$) nanoparticles were prepared via mechanochemical processing and subsequent heat treatment at a relatively low ($600^{\circ}C$) calcining temperature. The raw materials used were high purity $Fe_2O_3$ and $Li_2CO_3$ that were milled for between 2 and 20 h. The milled powders were then calcined at temperatures of 500 and $600^{\circ}C$ for 5 h in air. XRD results show that optimum conditions to obtain single phase lithium ferrite nanoparticles with a mean crystallite size of about 23 nm, using Scherrer's formula, are 10 h milling and calcination at $600^{\circ}C$. Saturation magnetization and coercivity of the single phase Li ferrite nanoparticles are 44.6 emu/g and 100 Oe respectively, which are both smaller than those of the bulk Li ferrite. The Curie temperature of the single sample was determined by a Faraday balance, which is $578^{\circ}C$ and smaller than that of bulk Li ferrite.

• Journal of Microbiology and Biotechnology
• /
• v.8 no.5
• /
• pp.449-454
• /
• 1998

A thennostable chitosanase was purified from Bacillus sp. KFB-C108, by fractionation of 30 to 70% saturation with ammonium sulfate, DEAE-Toyopearl chromatography, Butyl-Toyopearl chromatography, and TSK-Gel HW-55F gel filtration. The purified enzyme showed a single band on sodium dodecyl sulfate polyacrylamide gel electrophoresis, and the molecular weight was estimated to be 48 kDa. The enzyme degraded soluble chitosan and colloidal chitosan, but did not degrade glycol chitosan, chitin, and the other compounds investigated. There was no effect on the chitosanase activity by treatment with chelating agents, alkylating agents, and various metals investigated, and only cobalt ions inhibited the activity. Optimum temperature and pH were $55^{\circ}C$ and 6.5, respectively. The enzyme was stable after heat treatment at $80^{\circ}C$ for 10 min or $70^{\circ}C$ for 30 min and fairly stable in several organic solvents as well. Chitosan was hydrolyzed to $(GlcN)_4$as a major product by incubation with the enzyme.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.740-747
• /
• 1999

Grain refinement is the only strengthening mechanism that improves both strength and toughness. Controlled rolling and accelerated cooling techniques have been known to be effective method to improve the mechanical properties by controlling the recrystallization and/or grain coarsening during processing. Repeat phase transformation $(\gamma/\alpha)$ by repeat heat treating is another way of grain refinement. In this study, a combined effect of controlled rolling and repeat heat treating was investigated. To study the effects of Mo addition and process parameters, Mo alloyed low carbon steels were prepared and thermomechanical controlled processes were simulated in the Gleeble system. The Mo addition resulted in an increasement of the grain coarsening temperature and suppress austenite recrystallization. The optimum condition for the refinement of austenite was obtained when the controlled rolling was performed twice with the same heat treatment condition, and reduction ratio of second pass was higher than that of first pass.

• Resources Recycling
• /
• v.29 no.1
• /
• pp.70-80
• /
• 2020

This study investigates the effect of flux type and mixing ratio on efficiency in aluminum can scrap recycling using induction furnace. The removal of surface coating layer of aluminum can scrap was possible through heat treatment at about 500 ℃ for about 30 min. The temperature for the melting process was set to be slightly above the melting temperature of the aluminium can scrap. The molten metal treatment was performed with different types of flux and mixing ratio. As a result, The optimum efficiency of Al recovery ratio was revealed when the process was performed with at least 3 wt.% of the flux (Salt and MgCl₂ mixture of ratio 70:30) at 750 ℃. The mechanical property of the recovered Al alloy showed that the tensile strength is about 249 MPa and elongation is about 14 %. This result was found to be similar to the mechanical property of the virgin Al 5083 alloy.