• 한국정보전자통신기술학회논문지
• /
• 제7권1호
• /
• pp.20-25
• /
• 2014

차세대 친환경 조명인 LED소자는 온도가 올라갈수록 LED의 발광효율이 떨어지고 $80^{\circ}C$이상 올라갈수록 수명이 감소하고 스펙트럼선의 파장이 본래의 파장보다 장파장 쪽으로 이동하는 Red Shift현상 및 $T_j$ 상승에 따라 광 출력이 감소되는 큰 문제점이 대두되고 있어 열을 최소화 할 수 있는 방열설계 연구가 진행 중이다. COB Type LED의 경우 보드에 LED 칩을 직접 결합시켜 열 저항을 낮췄지만 주거용 13.5W의 경우 방열판을 통해 발열 문제를 해결해야한다. 본 논문에서는 주거용 13.5W COB LED 다운라이트에 맞게 Heat Sink를 설계하고, 그 설계한 Heat Sink와 13.5W COB를 패키징하여 Solidworks flow simulation을 통해 최적의 Fin두께를 선정하여 접촉식 온도계를 사용한 열적 특성을 분석 하고 평가 하였다.

• 한국정보통신학회논문지
• /
• 제14권7호
• /
• pp.1680-1686
• /
• 2010

가우스 광분포를 가지는 248nm 파장의 KrF 엑시머 레이저 빔과 1.072um 주기를 가지는 위상마스크를 이용하여 최저 투과율 파장이 1549.9nm 인 광섬유 브래그 격자(Fiber Bragg Grating)를 제작하였다. 레이저 빔과 마스크 그리고 광섬유의 최적 정렬 과정을 조사하기 위해 평행 정렬 오차와 각 정렬 오차가 조사되었고 또한 엑시머 레이저의 투과 에너지와 발진 주파수의 변화에 따른 영향도 조사되었다. 실험 결과 얻어진 최적 정렬 조건 하에서 제작된 광섬유 격자의 광 투과 스펙트럼 형성 과정을 측정하여 특성이 분석되었고 이 같이 사용된 제작 조건의 안정성을 확인하기 위해 재현성 실험이 수행되었다.

• 한국안광학회지
• /
• 제3권1호
• /
• pp.27-31
• /
• 1998

펄스형 방전플라즈마 발생장치인 플라스마 포커스장치에서 발생하는 가시광선영역의 빛을 시간분해분석법과 시간적분분석법으로 분광분석하였다. 플라스마포커스장치는 전극이 동축형으로 사용되었고, 시간 용해분석법은 고정된 파장의 광펄스를 오실로스코프로 분석하였으며, 시간 적분법을 일정한 범위의 파장대를 필림에 현상하여 densitometer로 분석하였다. 가시광선발생은 방전전압과 기체압력을 변수로 측정하여 방전전압은 17 kV이고 기체압력은 아르곤기체일 경우 0.5 torr가 최적조건이었다.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.251-262
• /
• 1995

The goal of this study is to provide fundamental information on the design of a new diesel injector system. The cylindrical disk spray was made by an impinging disk insited below the exit of air-assist atomizor. The disintegration processes on a twin-fluid atomization by air-assist atomizor were investigated. Liquid jet was disintegrated at the condition that wavelength was equal and longer than the circumference of the liquid jet, .lambda. .geq. .pi.do. However, the wavelength and the diameter of the liquid jet were decreased according to the increasing of air velocity. The relative density distribution of droplets and pattern of spray by impinging disk were investigated with a C-CCD. Optimum design conditions for cylindrical disk spray were also achieved. The pattern of cylindrical spray can classified according to the size of the disk and the distance from the nozzle tip to the disk. When the space of the disk and the nozzle tip was narrow and the diameter of the disk was larger than that of the air orifice of the nozzle exit, the good distribution of spray could be achieved. When the air flowrate was constant, the spray width was decreased according to the increasing of the liquid flowrate. When the liquid flowrate was constant, the spray width was decreased according to the increasing of the air flowrate.

• 한국항해항만학회지
• /
• 제32권9호
• /
• pp.723-727
• /
• 2008

Sensing performances of evanescent field absorption (EFA) hetero-core fiber sensor has been presented based on EFA by changing the length and the core diameter of the single mode fiber. Experimental results have demonstrated a good feature in their relationship between the length and the core diameter of the single mode fiber. The sensor consists of 2 fiber optics which have the same cladding diameter of $125{\mu}m$ However one fiber optic used is single mode and has varying core diameter ranging from 3.3 to $5.6{\mu}m$. The other fiber is multimode type and has a thicker fixed core diameter of $62.5{\mu}m$. The 2 fiber optics are thermally spliced together. Experiments conducted to measure the resonance wavelength were carried out over a range of refractive index, to find the optimum sensing length Experiments show that core diameter of the single mode fiber and sensing length offects the linearity and sensitivity.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1360-1363
• /
• 2006

A borate compound was adopted as new host material for $EU^{3+}$ activator. The $Eu^{3+}-doped\;YCa_3(GaO)_3(BO_3)_4$ (YCGB) phosphors were successfully synthesized. Also, their photoluminescence properties under the excitation of UV ray were measured. In the XRD patterns of the synthesized powders, most peaks were well-matched to a gaudefroyite phase. The emission of $Eu^{3+}$ in YCGB consists of a strong peak centered at 622 nm, which is attributed to $^5D_O-^7F_2$ transition of $Eu^{3+}$ and several weak peaks at near the wavelength. Optimum $Eu^{3+}$ concentration of the red phosphor under the excitation with the wavelength of 395 nm was about 75 mol%. This indicates that the red phosphor has a relatively higher critical concentration than that of the other $Eu^{3+}-doped$ phosphors. The dominant interaction character of $Eu^{3+}$ might be dipole-dipole interaction.

• Transactions on Electrical and Electronic Materials
• /
• 제4권2호
• /
• pp.35-39
• /
• 2003

This paper is contents on the orthorhombic crystalline calcined by the solid phase method with LiMnO$_2$ thin film structured as the result which an average pore diameter of power was 132.3${\AA}$ in porosity analysis. Voltage ranges are able to get the properties of charge and discharge for experimental results of LiMnO$_2$ thin film were 2.2V 4.3V. The current density and scan speed were 0. 1㎃/$\textrm{cm}^2$ and 0.2㎷/sec respectively. Properties of the charge and discharge are obtained by optimum experiment condition parameters. Li dense ratio of the LiMnO$_2$ thin film that discharged capacities were 87㎃h/g have been 96.9［ppm］ at 670.784［nm］ wavelength. The dense ratio of Mn analyzed to 837［ppm］ at 257.610［nm］ wavelength. It can be estimated the quality of the LiMnO$_2$ thin film as that the wrong LiMnO$_2$ thin film pulled up from cell of electrolyte and became dry it at 800$^{\circ}C$. The results of SEM and XRD were the same as that of original researchers.

• 대한화학회지
• /
• 제7권1호
• /
• pp.29-33
• /
• 1963

A new method determining the micro amount of cupferron spectrophotometrically was investigated and was considered on the various factors which affect on the method. The method was as follows; ferric alum solution was added in a suitably acidified solution of cupferron. After the precipitates of Fe(Ⅲ)-cupferrate were formed, they were extracted with chloroform and the absorbancy of the organic phase was measured by spectrophotometer, Beckmann Model B (1cm quartz cell). The stable maximum wavelength was 325 $m{\mu}$ at 3.0 to 5.6 of the optimum pH and it obeyed on Boer's law in the range of 5.76 ${\gamma}/ml$ to 74.80 ${\gamma}/ml$ of cupferron. The maximum wavelength was independent on pH, concentration of cupferron and of ferric alum. The absorbancy at 325 $m{\mu}$ was not affected by $SO_4^{--}$ and Ac, but was varied by $Cl^-$ and $NO_3^-$. Sulfuric acid and acetate buffer are preferred to the acid and buffer solution adjusting the pH. At higher acidity, however, the absorbancy was somewhat lowered because of the decomposition of cupferron, and at too high concentration of ferric alum, it was also decreased because of the difficulty in the extraction. By this method, it was able to determine cupferron quantitatively in the percent error of 1.18.

• 펄프종이기술
• /
• 제43권2호
• /
• pp.9-15
• /
• 2011

Fluorescent whitening agent (FWA) is a widely used chemical in paper industry, but a systematic and scientific method on FWA analysis has not been established. We performed the basic researches on the fluorescence analysis of FWA. The fluorescence of FWA was investigated using a spectrofluorometer and a spectrophotometer. When FWA solution was analyzed using the spectrofluorometer, we found that the peak wavelength of the fluorescence emission was about 440 nm and that of the fluorescence excitation was about 370 nm irrespective of FWA types. Papers dyed with an internal FWA were prepared in a laboratory and the reflectance and the fluorescence index were measured using the spectrophotometer. It was confirmed that the optimum peak wavelength of the reflectance was 440 nm and the fluorescence index calculated from the CIE whiteness with and without UV light under a light source D65 was the best indicator to measure the fluorescence of FWAs exiting in papers.

• 정보저장시스템학회논문집
• /
• 제1권2호
• /
• pp.182-187
• /
• 2005

A large area micro mirror is an optical element that functions as changing an optical path by reflection in integrated optical system. We fabricated the large area silicon mirror by anisotropic etching using MEMS for implementation of integrated optical pickup. In this work, we report the optimum conditions to better fabricate and design, greatly improve mirror surface quality. To obtain mirror surface of $45^{\circ},\;9.74^{\circ}$ off-axis silicon wafer from (100) plane was used in etching condition of $80^{\circ}C$ with 40wt.% KOH solution. After wet etching, polishing process by MR fluid was applied to mirror surface for reduction of roughness. In the next step, after polymer coating on the polished Si wafer, the Si mirror was fabricated by UV curing using a trapezoid bar-type way structure. Finally, we obtained peak to valley roughness about 50 nm in large area of $mm^2$ and it is applicable to optical pickup using blu-ray wavelength as well as infrared wavelength.