• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.641-645
• /
• 2002

In case of aluminum-cased battery, The ratio of height and base of square is generally above the ten times, square-shaped and problem of non-axis symmetry. It is typical model to set up the analysis method of finite element. The reliable analysis of finite element method is suggested, which is used to investigate the possibility that multi-stage deep drawing and ironing used currently is replaced by backward impact extrusion favorable in the respect of cost production and productivity. The influence of parameter was analyzed and compared, which was considered to analyze the process of large deformation plasticity such as extrusion. Die and billet was made as the same shape of finite element model. The results of experiment show good forming without the rupture and wrinkles with the optimum velocity 100mm/sec obtained by analysis.

• 소성∙가공
• /
• 제17권2호
• /
• pp.124-129
• /
• 2008

Net shape forging technologies give many effects into the costs and qualities for the finished products. So, the studies to reduce the additional machining amount are very important in forging industry. Specially, there are two main topics in cold forging industry, such as, tool life and precision forging. In this study, new forging technique was proposed to eliminate the machining process for fixing up the length and improve the lead accuracy of gear. The luck-up hub is manufactured through many processes, such as upsetting, piercing and direct extrusion. The gear is formed in direct extrusion process; however, lead accuracy of the gear is over allowance limit. Therefore, the additional sizing process must be added. In this study, process design for closed-die forging of a lock-up hub used for a component of automobile transmission was made using three-dimensional finite element simulations, and the strain distributions and velocity distributions are investigated through the post processor. The rigid-plastic finite-element method for back pressure forging has been used in order to reduce development time and die cost. Using the FEM simulation, we found the optimum value of back pressure. The prototypes of lock-up hub parts were forged into the net-shape. In the experiment, lead precision of tooth are measured by the CCMM(Contact Coordinate Measuring Machine). The dimensional accuracy of forged part was improved up to the 40% when back press was applied.

• 소성∙가공
• /
• 제15권4호
• /
• pp.295-303
• /
• 2006

Optimization is carried out to determine process parameters which reduce the amount of springback and improve shape accuracy of a deep drawn product in sheet metal forming process. The study uses the amount of stress deviation along the thickness direction in the deep drawn product as an indicator of springback instead of springback simulation. The scheme incorporates with an explicit elasto-plastic finite element method for calculation of the final shape and the stress deviation The optimization method adopts the response surface method in order to seek for the optimum condition of process parameters such as the blank holding force and the draw-bead force. The present scheme is applied to design of the variable blank holding force in an U-draw bending process and the application is further extend ε d to the design of draw-bead force in a front side member formed with advanced high strength steel (AHSS) sheets of DP60. Results show that design of process parameter is well performed to decrease the stress deviation through the thickness and to reduce the amount of springback. The present analysis provides a guideline in a design stage for controlling the springback based on the finite element simulation of the complicated parts.

• 한국정밀공학회지
• /
• 제28권2호
• /
• pp.219-225
• /
• 2011

Silicone resin is recently used as encapsulant for high-power LED module due to its excellent thermal and optical properties. In the present investigation, finite element analysis of cure process was attempted to examine residual stress evolution behavior during silicone resin cure process which is composed of chemical curing and post-cooling. To model chemical curing of silicone, a cure kinetics equation was evaluated based on the measurement by differential scanning calorimeter. The evolutions of elastic modulus and chemical shrinkage during cure process were assumed as a function of the degree of cure to examine their effect on residual stress evolution. Finite element predictions showed how residual stress in cured silicone resin can be affected by elastic modulus and chemical shrinkage behavior. Finite element analysis is supposed to be utilized to select appropriate silicone resin or to design optimum cure process which brings about a minimum residual stress in encapsulant silicone resin.

• 수산해양기술연구
• /
• 제30권1호
• /
• pp.53-63
• /
• 1994

1) 강소성 유한 요소법 프로그램 RDHPSC는 2단헤딩 가공에 있어서의 신뢰 할 수 있는 해석수단이다. 2) RDHPSC에 의한 2단헤딩의 해석은 2단헤딩가공에서의 최적 가공 조건의 결정에 유용한 정보를 제공할 수 있다. 3) 2단헤딩 가공중의 금속흐름을 수치해석에서의 격자 변형에 의해 관찰될 수 있다. 4) 2단헤딩 가공중의 표면 결함의 발생가능성은 수치해석 결과에서 원수방향응력과 계수 D를 관찰함으로서 탐색되어질 수 있다. 5) 2단헤딩가공중에 있어서의 내부결함 발생가능성은 수치해석의 격차 변형을 통하여 알 수 있다. 6) 마무리 가공금형 수명에 대한 최적가공조건은 수치해석에서의 접촉압력을 조사하여 얻을 수 있다.(이 논문의 결론부분임)

• 산업식품공학
• /
• 제13권4호
• /
• pp.269-274
• /
• 2009

습식분쇄의 최적조건을 얻고자 부형제 종류, 농도, 습식 분쇄시 rotor speed, bead size, feed rate, 분쇄회수를 달리하여 분쇄한 결과, 부형제로는 gum arabic을 사용하여 5%의 농도로 첨가할 때 가장 좋은 분쇄효과를 나타내었다. Rotor speed를 달리하여 습식분쇄한 결과, rotor speed가 증가할수록 좋은 결과를 나타내어 4,000 rpm에서 가장 우수한 것으로 나타났다. 원료와 직접 부딪혀 분쇄를 하게 되는 bead는 0.4 mm의 크기를 사용하였을 때 가장 작은 사이즈로 분쇄되는 것으로 나타났다. 분쇄가 이루어지는 chamber내에 원료를 공급하는 비율에 따른 결과에서는 40 L/h 의 속도로 공급했을 때 가장 작은 입도분포를 보였다. 분쇄회수에 따른 영향은 횟수에 따라서는 8회 이상으로 분쇄하였을때 0.6 $\mu$m이하의 입도분포가 90% 이상으로 나타나 10회를 분쇄하였을때 가장 좋은 효과를 나타내었다. 연속운전과 비연속운전의 비교에서는 연속운전이 더 효율적이었으며 부형제 종류에 따른 영향은 gum arabic을 첨가하여 분쇄하였을때 가장 우수한 결과를 나타내었다. 따라서 적절한 농도와 종류의 부형제 사용과 rotor speed, bead size, feed rate, 용매와의 혼합비의 최적공정을 수립한 습식 분쇄기술로 초미세액상칼슘의 제조가 가능하였고, 습식분쇄기술을 식품가공기술로 활용할 수 있는 가능성을 확보하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.245-249
• /
• 2009

According to the increase of intelligent vehicles many automotive electric components are installed. The wire harness which connects those also increases. The crimping process for compressing the copper wire bundle into the terminal is a key process to assure the good quality of wire harness. For the case of inadequate forming condition many shape failures such as less-filling, over-filling are happen in the crimping process. Even though the quality of crimping shape is satisfactory the quality check for electrical resistance of wire harness is sometime not satisfied the qualification due to large variation of electrical resistance of wire harness under climate test. This large variation is thought to be related with the malfunction automotive electric system and caused by the internal stress of wire, which occurred during the crimping process. In this paper we develop the 3D-FEM simulation scheme and design methodology of optimum terminal shape. Also the effect of terminal shape on the residual stress is discussed.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권2호
• /
• pp.49-56
• /
• 2003

As semi-solid forging (SSF) is compared with conventional casting such as gravity die-casting and squeeze casting, the product without inner defects can be obtained from semi-solid forming and globular microstructure as well. Generally, SSF consists of reheating, forging, and ejecting processes. In the reheating process, the materials are heated up to the temperature between the solidus and liquidus line at which the materials exists in the form of liquid-solid mixture. The process variables such as reheating time, reheating temperature, reheating holding time, and induction heating power has large effect on the quality of the reheated billets. It is difficult to consider all the variables at the same time for predicting the quality. In this paper, Taguchi method, regression analysis and neural network were applied to analyze the relationship between processing conditions and solid fraction. A356 alloy was used for the present study, and the learning data were extracted from the reheating experiments. Results by neural network were in good agreement with those by experiment. Polynominal regression analysis was formulated using the test data from neural network. Optimum processing condition was calculated to minimize the grain size and solid fraction standard deviation or to maximize the specimen temperature average. Discussion is given about reheating process of row material and results are presented with regard to accurate process variables fur proper solid fraction, specimen temperature and grain size.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.401-402
• /
• 2006

All-surface, all-tooth machining and roll forming of cast iron have been used to manufacture the crankshaft position sensor wheel (CPSW). However, these methods pose many problems such as difficult processing, high material cost, and low tooth precision. Thus, we developed a sintered CPSW with an improved detection ability in order to resolve the problems related with the previous methods of manufacturing CPSW by simplifying the process flow and improving tooth precision. The sintering process is introduced in this study. We conducted an experiment to compare the sintered and roll formed products and analyzed the results to evaluate the reliability of the sintering process. Furthermore, we compared and analyzed stress and displacement in the sintered and roll formed products through the "Finite Element Method(FEM)". According to the experimental and FEM results, the sintered product showed satisfactory mechanical properties. It was less expensive to process and lighter and showed better quality than the roll formed product. The results of this study could be applied to design an optimum CPSW using the sintering process.

• 미래기술융합논문지
• /
• 제2권2호
• /
• pp.9-14
• /
• 2023

이 연구는 1050MPa급 경량 연성 주철 주관류 컨트롤 암을 개발하기 위한 첫 해의 결과를 보여줍니다. 첫째, 최적 설계 구조를 위한 레이아웃 설계 및 구성 요소 개발, 그리고 컨트롤 암 강성과 최적 구조 디자인 및 강건성 설계를 통해 예상 응력을 제어하는 중점 영역의 강건성을 달성합니다. 둘째, 높은 강성과 고성능 경량 구조를 반영하는 컨트롤 암을 개발합니다. 중공을 통해 소비자가 요구하는 설계와 강성을 충족시키기 위해 개발된 컨트롤 암은 코어 제작 공정을 개발합니다. 셋째, 최적의 합금 조성과 열처리 방법을 통해 철 합금 (Cu, Ni, Mo)의 양과 Austempered 열처리 및 조화 상태를 도출합니다. 넷째, 저강도, 고강성 구성 요소 개발을 위해 최적의 성형기술 개발을 통해 최적의 주조 기술 개발로 이어지는 구성 요소 개발을 위한 높은 강도의 주조 형성 기술을 개발하기 위한 시도를 합니다.