• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.991-997
• /
• 2004

In this paper, we propose the architecture of modem receiver to fabricate HomePNA 2.0 chip. HomePNA suffers from inferior channel because of bridge tap, the effect of amateur HAM band and so on. To transfer data over such channel, HomePNA 2.0 uses training sequence to equalize channel and uses FD-QAM optionally as modulation method. So modem receiver demodulate QAM based signal and needs optimum architecture that fully uses these transmission feature. As a result of research, we define 2 mode function of modem receiver depending on TX/RX state. In this paper, particularly, we show the algorithm of equalizer, carrier phase recovery and frame synchromzationblock and propose architecture that improve the performance of channel equalization and is stable in operation. In the end, we estimate the performance of proposed HomePNA2.0 modem receiver over HomePNA TEST LOOP using SPW program.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.361-362
• /
• 2006

This paper presents the robust design of gripper part for a high-speed LCD (Liquid Crystal Display) transfer system. In this paper, the 1st DOE (Design of Experiment) is conducted to find out main-effect factors fur the design of gripper part. Thirty-six experiments are performed using $ANSYS^{(R)}$ and their results are statistically analyzed using $MINITAB^{(R)}$, which shows that the factors, i.e., First-width, Second-width, Rec-width, and thickness of gripper part, are more important than other factors. The main effect plots shows that the maximum deflection and mass of gripper part are minimized by increasing First-width, Second-width, Rec-width and thickness. The 2nd DOE is conducted to obtain RSM (Response Surface Method) equation. The CCD (Central Composite Design) technique with four factors is used. Optimum design is conducted using the RSM equation. Genetic algorithm is used for optimal design. Six sigma robust design is conducted to find out a guideline for control range of design parameter. To obtain six sigma level reliability, the standard deviations of design parameters are shown to be controlled within 5% of average design value.

• Journal of Korean Society on Water Environment
• /
• v.22 no.5
• /
• pp.856-864
• /
• 2006

For estimating the minimum discharge to maintain a river, low flow analysis is required and long term runoff records are needed for the analysis. However, runoff data should be estimated to run a hydrologic model for ungaged river basin. For the reason, parameter estimation is crucial to simulate rainfall-runoff events for those basins using Tank model. In this study, only runoff data recorded for dry season are used for parameter estimation, which is different to other methods based on runoff data recorded for wet and dry seasons. The Harmony Search algorithm is used to determine the optimum parameters for Tank model. The coefficient of determination ($R^2$) is served as the objective function in the Harmony Search. In cases that recorded data are insufficient, the recording interval is changed and Empirical CDF is adopted to analyze the estimated parameters. The suggested method is applied to Yongdam dam, Soyanggang dam, Chungju dam and Seomjingang dam basins. As results, the higher $R^2s$ are obtained when the shorter recording interval, the better recorded data quality, and the more rainfall events recorded along with certain rainfall amount is. Moreover, when the total rainfall is higher than the certain amount, $R^2$ is high. Considering the facts found from this study for the low flow analysis, it is possible to estimate the parameters for Tank model properly with the desired confidence level.

• Journal of Broadcast Engineering
• /
• v.7 no.1
• /
• pp.55-65
• /
• 2002

Wavelet transform has recently emerged as a promising technique for video processing applications due to its flexibility in representing non-stationary video signals. Motion estimation which uses wavelet transform of octave band division method is applied In many places but if motion estimation error happens in the lowest frequency band. motion estimation error is accumulated by next time strep and there has the Problem that time and the data amount that are cost In calculation at each steps are increased. On the other hand. wavelet packet that achieved the best image quality in a given bit rate from a rate-distortion sense is suggested. But, this method has the disadvantage of time costs on designing wavelet packet. In order to solve this problem we solved this problem by introducing Top_down method. But we did not find the optimum solution in a given butt rate. That image variance can represent image complexity is considered in this paper. In this paper. we propose a fast multiresolution motion estimation scheme based on the adaptive wavelet transform for video compression.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.5
• /
• pp.33-41
• /
• 2006

In the modem power distribution systems, there are lots of zero-phase current harmonics in the neutral power line due to much usages of the controlled switching devices, various semiconductor power converting systems, OA(Office Automation) equipments, PC etc. In order to minimize the current harmonics a zero-phase neutral line current eliminating reactor (NHER) is designed and analyzed its performance using the finite element program. For the design of NHER a program is developed using C++ program. To verify the program a case model(380/220[V], 200[A]) is designed and analyzed by the developed program. As the results of the optimal design, the core loss is reduced by 26[%] with eliminating of the current harmonics. Especially the ninth harmonics is much reduced as compared with the others. When the design of NHER is adapted to the load of the power system, the eliminating effect and efficiency of the device will be much better

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.21 no.4
• /
• pp.373-379
• /
• 2019

Smart-farm has been spreading across Korea to improve the labor efficiency and productivity of greenhouse crops. Although notable improvements have been made in the monitoring technologies and environmental-controlling systems in greenhouses, only a few simple decision-support systems are available for predicting the optimum environmental conditions for crop growth. In this study, a tomato growth model (GreenTom), which was developed by Seoul National University in 1997, was calibrated and validated to examine if the model can be used as a decision-supporting system. The original GreenTom model was not able to simulate artificial defoliation, which resulted in overestimation of the leaf area index in the late growth. Thus, an algorithm for simulating the artificial defoliation was developed and added to the original model. The node development, leaf growth, stem growth, fruit growth, and leaf area index were generally well simulated by the modified model indicating that the model could be used effectively in the decision-making of smart greenhouse.

• Journal of the Korean Magnetics Society
• /
• v.20 no.2
• /
• pp.61-67
• /
• 2010

As a high energy permanent magnet is commonly applied to motors so that small motors have high power capacities, it is also necessary to reduce a cogging torque which causes a noise and vibration in permanent magnet motors. The patterns of cogging torque in permanent magnet motors depend on the magnetic field distributions, so it is possible to reduce a cogging torque by designing a core shapes optimally. But it is known that an optimum design algorithm for reduction of cogging torques is too complicated and the process to get an optimized core shape is time consuming task. In this paper, new simplified core shapes are suggested to reduce a design parameters so that the core shapes to reduce a cogging torques could be obtained with simple computations. The result shows that the cogging torques of permanent magnet motors with this simplified core shapes could be reduced effectively without any loss of average torques.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.6
• /
• pp.29-37
• /
• 2016

This paper proposes a shape optimization of the metal boss for a composite motor case using finite element analysis. For the structural safety and the weight reduction of the composite motor case, under the internal pressure, the fiber stress in the dome area and the tightening bolt stress are constrained and the boss weight is set to objective function, respectively. The response surface models are constructed for the performance characteristics by using response surface method. The significance of the design variables about the performance characteristics is evaluated through the ANOVA(analysis of variance) and the goodness of fit test for the constructed model is performed through the regression analysis. The SQP(sequential quadratic programming) algorithm is used for the optimization and the proposed method is verified by performing structural analysis for the optimum shape.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.1
• /
• pp.100-114
• /
• 2015

This paper deploys optimization techniques to obtain the optimum hull form of KSUEZMAX at the conditions of full-load draft and design speed. The processes have been carried out using a RaPID-HOP program. The bow and the stern hull-forms are optimized separately without altering neither, and the resulting versions of the two are then combined. Objective functions are the minimum values of wave-making and viscous pressure resistance coefficients for the bow and stern. Parametric modification functions for the bow hull-form variation are SAC shape, section shape (U-V type, DLWL type), bulb shape (bulb height and size); and those for the stern are SAC and section shape (U-V type, DLWL type). WAVIS version 1.3 code is used for the potential and the viscous-flow solver. Prior to the optimization, a parametric study has been conducted to observe the effects of design parameters on the objective functions. SQP has been applied for the optimization algorithm. The model tests have been conducted at a towing tank to evaluate the resistance performance of the optimized hull-form. It has been noted that the optimized hull-form brings 2.4% and 6.8% reduction in total and residual resistance coefficients compared to those of the original hull-form. The propulsive efficiency increases by 2.0% and the delivered power is reduced 3.7%, whereas the propeller rotating speed increases slightly by 0.41 rpm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.7B
• /
• pp.538-549
• /
• 2008

Recently IEEE 802.22 WG has considered Cognitive Radio (CR) technology to overcome shortage of communication channels. For using CR technology, accurate and rapid sensing method selection is extremely important. According to the channel sensing method, it is of the utmost importance because it can affect the incumbent system protection. So, optimum selection of channel sensing method is very important. IEEE 802.22 gives the solution, name of fine sensing, but the solution can not adapt to various networks. So in this paper we propose Policy-based Channel Sensing Architecture and Algorithms for Cognitive Radio Networks. The proposed channel sensing architecture and algorithms can reduce both primary system detection time and quiet time in our simulation. Among the proposed sensing algorithm, channel division round robin sensing reduce average detection time up to 70% compare to fine sensing method in IEEE 802.22.