• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.6
• /
• pp.585-589
• /
• 1999

In order to grow $Bi_4Ge_3O_{12}$ crystals by the Czochralski method equipped with the auto-diameter control system, we used the resistance heater of our own design. We measure the temperature gradients under-arious thermal configurations. The relation between the critical rotation rate corresponding to the flat interface and the temperature gadient was investigated, and the importance of the axial temperature gradient was pointed out. The results from this work were compared with those obtained by other authors when RF heating was used. The optimal conditions for the crystal growth were determined as follows; under $O_2$ atmosphere with the pulling rate fixed at 2 mm/hr, rotation rate changed from 30 to 23 rpm as the crystal growth proceeded, radial and axial temperature gradients were 50 and $40^{\circ}C$/cm near melts respectively, and the composition was chemically stoichiometric.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.66 no.4
• /
• pp.242-246
• /
• 2017

In this study, it was investigated about optical simulation in high brightness and high uniformity general lighting using glass light guide plate. And we adopt edge-light emission type light plate. Edge-light type lighting has been used LCD application, especially note PC or smart phone backlight unit. Because it had the good properties such as slim shape and light weight. We thought this type was suitable for general lighting application such as wall attached type or ceiling mount type. But many of edge-light type lighting had problems. It called slanted output light rays. That was main key parameter how could control the direction of output light rays. We investigated the solution of this problems, using ray tracing method, we recognized the major fact of the solution relied on the geometric structure of diffusing dot shape. We set the conditions of aspect ratio in diffusing dot shape such as 0.5 to 1. And, at first, we designed diffusing dots shape based on the results of optical simulation and made specimen. as above condition, and acquired good result in confirming dots shape such as the value of the output rays's peak angle was around 75 degrees. And good light distribution characteristics were measured by slated spectro-radiometer. It was shown that the effective ways of designing light distribution characteristics using optical simulation such as ray tracing linear method for making general lighting using glass light guide plate.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.373-376
• /
• 2018

Traditional paprika smart farm systems are often harmful to paprika growth because they are set to follow the values of several sensors to the reference value, so the system is often unable to make optimal judgement. Using decision tree techniques, the expert system for the paprika smart farm is designed to create a control system with a decision-making structure similar to that of farmers using data generated by factors that depend on their surroundings. With the current smart farm control system, it is essential for farmers to intervene in the surrounding environment because it is designed to follow sensor values to the reference values set by the farmer. To solve this problem even slightly, it is going to obtain environmental data and design controllers that apply decision tree method. The expert system is established for complex control by selecting the most influential environmental factors before controlling the paprika smart farm equipment, including criteria for selecting decisions by farmers. The study predicts that each environmental element will be a standard when creating smart farms for professionals because of the interrelationships of data, and more surrounding environmental factors affecting growth.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.12
• /
• pp.1678-1687
• /
• 2013

This paper describes a prototype of 3-phase 3.3kV/220V 6kVA modular semiconductor transformer developed in the lab for feasibility study. The developed prototype is composed of three single-phase units coupled in Y-connection. Each single-phase unit with a rating of 1.9kV/127V 2kVA consists of a high-voltage high-frequency resonant AC-DC converter, a low-voltage hybrid-switching DC-DC converter, and a low-voltage hybrid-switching DC-AC converter. Also each single-phase unit has two DSP controllers to control converter operation and to acquire monitoring data. Monitoring system was developed based on LabView by using CAN communication link between the DSP controller and PC. Through various experimental analyses it was verified that the prototype operates with proper performance under normal and sag condition. The system efficiency can be improved by adopting optimal design and replacing the IGBT switch with the SiC MOSFET switch. The developed prototype confirms a possibility to build a commercial high-voltage high-power semiconductor transformer by increasing the number of series-connected converter modules in high-voltage side and improving the performance of switching element.

• The KIPS Transactions:PartC
• /
• v.11C no.7 s.96
• /
• pp.905-916
• /
• 2004

Self-organizing hierarchical ad hoc network (SOHAN) is a new ad-hoc network architecture designed to improve the scalability properties of conventional 'flat' ad hoc networks. This network architecture consists of three tiers of ad-hoc nodes, i.e.. access points, forwarding nodes and mobile nodes. This paper presents a topology discovery and routing protocol for the self-organization of SOHAN. We propose a cross-layer path metric based on link quality and MAC delay which plays a key role in producing an optimal cluster-based hierarchical topology with high throughput capacity. The topology discovery protocol provides the basis for routing which takes place in layer 2.5 using MAC addresses. The routing protocol is based on AODV with appropriate modifications to take advantage of the hierarchical topology and interact with the discovery protocol. Simulation results are presented which show the improved performance as well as scalability properties of SOHAN in terms of through-put capacity, end-to-end delay, packet delivery ratio and control overhead.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.38-45
• /
• 2004

This paper studies the effects of intake port configuration on the swirl that is key parameter in the flow field of direct injection diesel engines. In-cylinder flow characteristics is known to have significant effects on fuel air mixing, combustion and emissions. To investigate the swirl flow generated by various intake ports, steady state flow tests were conducted to evaluate the swirl. Helical port geometry, SCV shape and bypass were selected as the design parameters to increase the swirl flow and parametric study was performed to choose the optimal port shape that would generate a high swirl ratio efficiently. The results revealed that a key factor in generating a high swirl ratio was to suitably control the direction of the intake air flow passing through the valve seat. For these purposes, we changed the distance of helical and tangential port as well as installed bypass near the valve seat and the effects of intake port geometry on in-cylinder flow field were visualized by a laser sheet visualization method. From the experimental results, we found that the swirl ratio and mass flow rate had a trade off relation. In addition, the result indicates that the bypass is a effective method to increase the swirl ratio without sacrificing mass flow rate.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.2
• /
• pp.279-290
• /
• 2022

A superconducting fault current limiter(SFCL) is a power device that exploits superconducting transition to control currents and enhances the flexibility, stability and reliability of the power system within a few milliseconds. With a high phase transition speed, high critical current densities and little AC loss, high-temperature superconducting (HTS) wires are suitable for a resistive-type SFCL. However, HTS wires due to the lack of optimization research are rather inefficient to directly apply to a fault current limiter in terms of the design and capacity, for the existing method relied the characteristics. Therefore, in order to develop a suitable wire for an SFCL, it is necessary to enhance critical current uniformity, select optimal stabilizer materials and conducted research on the development of uniform stabilizer layering technology. The high temperature superconducting wires manufactured by this study get an average critical current of 804 A/12mm-width at the length of 710m; therefore, conducted research was able to secure economic performance by improving efficiency, reducing costs, and reducing size.

• Clean Technology
• /
• v.28 no.3
• /
• pp.227-231
• /
• 2022

The demand for high-voltage power devices is rising in various industries, but especially in the transportation industry due to autonomous driving and electric vehicles. IGBT module parts of 3.3 kV or more are used in the power propulsion control device of electric vehicles, and the procurement of these parts for new construction and maintenance is increasing every year. In addition, research to optimize high-voltage IGBT parts is urgently required to overcome their very high technology entry barrier. For the development of high-voltage IGBT devices over 3.3 kV, the resistivity range setting of the wafer and the optimal conditions for major unit processes are important variables. Among the manufacturing processes to secure the optimal junction depth, the optimization of the diffusion process, which is one step of the unit process, was examined. In the diffusion process, the type of gas injected, the injection time, and the injection temperature are the main variables. In this study, the range of wafer resistance (Ω cm) was set for the development of high voltage IGBT devices through unit process simulation. Additionally, the well drive in (WDR) condition optimization of the diffusion process according to temperature was studied. The junction depth was 7.4 to7.5 ㎛ for a ring pattern width of 23.5 to25.87 ㎛, which can be optimized for supporting 3.3 kV high voltage power devices.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.8A
• /
• pp.1160-1168
• /
• 2000

This paper presents a real-time integrated traffic management (RITM) scheme that can effectively manage variable bit rate (VBR) and available bit rate (ABR) traffics having unpredictable characteristics in asynchronous transfer mode (ATM) networks. An unique feature of this scheme is that it has a special ATM cell control block which makes it possible to monitor bursty traffics in real-time so that the delay incurred to measure cell arrival rate is minimized. Additionally, the proposed scheme intends to dynamically reassign the leftover network resources to VBR/ABR connections without any deterioration in quality of service (QoS) of the existing connections. The RITM scheme has been verified to reliably monitor incoming traffics and to efficiently manage network resources by computer simulations. The capability of managing the incoming ATM traffics in real-time helps determine an optimal acceptable number of user connections for a given network condition. We can use this value as a threshold to protect the network from being congested and to find out a cost-effective buffer design method.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.151-160
• /
• 1994

Recently, terrestrial photogrammetry has been applied effectively to data acquisition in GIS and to monitoring precise machinery for simulation test. Because 3-D coordinates of many object points can be quickly measured with constant accuracy and easy modeling by this method. In this study, the composition concerned with multi-camera system which simultaneously analyzes structure from multi-station using various cameras was developed. The errors of results were analyzed to investigate the accuracy of the system, error of unknown points and control points, convergent and strip adjustment for optimal network design also. As results of this study, the efficiency of multi-camera system developed here was proved through application to monitoring the entire area of the precise model ship. We could also acquire 3-dimensional coordinates with good accuracy by arranging pass points. Therefore, possibility of measurement of instantaneous deformation as well as precision analysis of structures can be suggested.