• 소성∙가공
• /
• 제24권1호
• /
• pp.28-36
• /
• 2015

After a short review of the iterative optimal blank method, a new method of measuring the shape error for stamped parts with 3D contour lines, which is an essential component of the optimal blank design, is proposed. When the contour line of the target shape does not exist in a plane, but exists in 3D space, especially when the shape of the target contour line is very complicated as in the real automotive parts, then the measurement of the shape error is critical. In the current study, a method of shape error measurement based on the minimum distance is suggested as an evolution of the radius vector method. With the proposed method, the optimal blank shapes of real automotive parts were found and compared to the results of the radius vector method. From the current investigation the new method is found to resolve the issues with the radius vector method.

• 한국정밀공학회지
• /
• 제16권10호
• /
• pp.101-108
• /
• 1999

Most of researches for deep drawing process have been performed on the formability of axisymmetric blank, but there is an insufficient study on the formability of non-axisymmetric blank. In addition, the conventional blank shape has been determined by the trial-and-error method using industrial experience and post processing test. Therefore only approximated shape of the blank can be presented. In this study, the optimal blank shape and concrete drafting method in deep drawing process with biaxisymmetric elliptical shape is proposed. Through the deep drawing experiment, it is found that the optimal blank shape gives the most uniform thickness of the products in the first process

• 소성∙가공
• /
• 제13권1호
• /
• pp.90-101
• /
• 2004

An inverse mosaic method has been proposed to generate an initial blank shape from the final product shape. Differently from the geometric mapping method, the method can handle triangular patches. However, the generated blank shape is strongly dependent on the order of determination of nodes. In order to compensate the dependency error smoothing technique has been also developed. Although the accuracy has been improved greatly compared with the geometrical mapping method, the method has limitation, due to the no incorporation of plasticity theory. Even though the accuracy of the radius vector method is already proved. the method requires initial guess to start the method. In order to compromise the limitation of the present method and the radius vector method, the method has been connected to the radius vector method. The efficiency of the present optimal blank design method has been verified with some chosen examples.

• 한국기계가공학회지
• /
• 제7권4호
• /
• pp.31-36
• /
• 2008

Sheet metal forming has some merits that are less loss of materials in process, less time-consuming and it makes mass product possible. The product produced by sheet metal forming process has high strength compared to the weight and better surface characteristics. Therefore, sheet metal forming process is a lot used in automobiles, aircrafts, electronics and appliances. This paper made the process design for forming Bracket Front Back Frame Lower, determined the blank shape and size using PAM-STAMP, commercial software and evaluated formability. It has been proved that the optimal blank through the result forming analysis has advantage in terms of formability and spring back compared to the rectangular blank.

• 소성∙가공
• /
• 제3권3호
• /
• pp.335-346
• /
• 1994

The effect of sheet steel properties and lubrication on the optimal range of blank holding force (BHF) was investigated by means of the model die stamping of various sheet steels. The optimal range of blank holding force was expressed as the range between the lower BHF at flange wrinkling and the upper BHF at local necking. It showed that mechanical properties, thickness of sheet steel and lubrication condition were important factors affecting the optimal range of BHF in sheet steels. Especially, lubrication played an important role in the case of coasted sheet steels.

• 한국정밀공학회지
• /
• 제32권11호
• /
• pp.945-952
• /
• 2015

In drawing sheet metal, the blank holding force is applied to prevent wrinkling of the product and to add a tensile stress to the material for the plastic deformation. Applying an inappropriate blank holding force can cause wrinkling or fracture. Therefore, it is important to determine the appropriate blank holding force. Recent developments of the servo cushion open up the possibility to reduce the possibility of fracture and wrinkling by controlling the blank holding force along the stroke. In this study, a method is presented to find the optimal variable blank holding force curve, which uses statistical analysis with consideration of the nonlinear deformation path. The optimal blank holding force curve was numerically and experimentally applied to door inner parts. Consequently, it was shown that the application of the variable blank holding force curve to door inner parts could effectively reduce the possibility of fracture and wrinkling.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.85-88
• /
• 2001

Deep drawing process, one of sheet metal forming methods, is used widely. Circular or square shape blanks are currently studied mainly. Especially, circular blank for coating case of chip condenser remains bridges when it is made out of aluminum coil. The bridge reduces Material-withdrawal-rate of aluminum coil to $60\%$. This paper proposes a no-bridge blank instead of circular blank. To get the different values of two cases, comparison circular blank with no-bridge blank is accomplished in the point of thickness strain in the vicinity of flange. In order to find optimal condition in new proposed blank, several process variables - those are blank holder shape, die shape radii, punch shape radii and blank holding force - are changed.

• 소성∙가공
• /
• 제29권5호
• /
• pp.272-281
• /
• 2020

As the thickness of mobile communication devices is getting thinner, the size of the internal parts is also getting smaller. Among them, the battery case requires a high-level deep drawing technique because it has a rectangular shape with a large aspect ratio. In this study, the initial blank shape was optimized to minimize earing in a multi-stage deep drawing process using an artificial neural network(ANN). There has been no reported case of applying artificial neural network technology to the initial blank optimal design for a square case with large aspect ratio. The training data for ANN were obtained though simulation, and the model reliability was verified by performing comparative study with regression model using random sample test and goodness-of-fit test. Finally, the optimal design of the initial blank shape was performed through the verified ANN model.

• 대한기계학회논문집A
• /
• 제21권7호
• /
• pp.1141-1148
• /
• 1997

In the stamping industry the blank shape to be stamped into a designed shape has been conventionally determined from the try out process by the press engineers. The work needs a lot of time and thus leads a loss of productivity. In this study boundary element method for 2-dimensional potential problem was used to design optimum blank shapes for irregular press forming. Here we assumed that the blank is controlled by blank holder only and material flow at blank holder was under potential flow. The developed PC code for designing the optimum blank shape shows that the blank shapes for optimal drawing can be calculated within a few minute in pentium PC and the calculated shapes agree well with the experiments. However the application of this method is constrained only to the pressed product with flat bottom.

• 한국기계가공학회지
• /
• 제15권5호
• /
• pp.93-99
• /
• 2016

The trimming process is required for satisfying the dimensions of a final product in the hot stamping process. In general, the mechanical trimming or laser trimming process is applied after hot stamping. However, these processes have several disadvantages such as short tool life and low productivity. Therefore, in this study, the optimal trimless blank shape for the hot stamping process of a sill side was designed to remove the trimming process after hot stamping. In order to design the trimless blank, numerical analysis was performed. Firstly, CFD analysis was carried out to predict the cooling temperature and holding time of the hot stamping process. Then, the optimal trimless blank shape was determined through FE analysis. The effectiveness of the designed trimless blank shape was verified through a hot stamping experiment at an actual industrial site.