• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.46.2-46.2
• /
• 2010

For use of superstrate thin-film solar cells, surface texture of the transparent conductive oxide (TCO) has been used to enhance short-circuit currents by increasing light trapping into the cell. ZnO:Al films were deposited by using DC magnetron sputtering on glass substrates with ceramic (ZnO:$Al_2O_3$) target. The as-deposited TCO before texturing exhibited high transparencies (T > 85% for visible light including all reflection losses) and excellent electrical properties ($r=3-6{\times}10^{-4}{\Omega}.cm$). The optical and electrical properties of the TCO are influenced by the texturing conditions such as not only etchant dilutions but also etching time. We obtained the haze value of 14-16 resulting in increase in light trapping and short-circuit currents also.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.86-88
• /
• 2004

As the rapid incensement of the number of internet users has occurred recently, many multimedia application services have been emerging. To improve quality of service, traffic can be suggested to be classified with priority in EPON(Ethernet Passive Optical Network), which is supporting the multimedia application services. In this paper, multimedia application services treat bandwidth classifying device in serving both delay sensitive traffic for real-time audio, video and voice data such as VoIP(Voice over Internet Protocol), and nonreal-time traffic such as BE(Best Effort). With looking through existing mechanisms, new mechanism to improve the quality will be suggested. The delay performances and packet losses of traffic achieved by supporting bandwidth allocation of upstream traffic in suggested mechanism will be analyzed with simulation.

• Journal of Photoscience
• /
• 제12권2호
• /
• pp.95-100
• /
• 2005

We have synthesized an azobenzene-containing polymer (PEA) and a stilbene-containing polymer (PAS) with second-order nonlinear properties. The second harmonic coefficient ($d_{33}$) of the poled polymer films was 84 and 36 pm/V for of PEA and PAS, respectively. The poled state of these polymers was stable at least up to 30 h at room temperature. $T_g$ of these polymers appeared in the range from 120 to $160^{\circ}C$ and onset of initial weight losses in the range from 260 to $270^{\circ}C$. Silicon moieties in the main chain enhanced the solubility of PEA and PAS in common organic solvents such as chloroform, N-methylpyrrolidinone (NMP), N, N-dimethylformamide (DMF), etc.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.844-847
• /
• 2001

In this work, transient characteristics of the Non-Punch Through(NPT) Insulated Gate Bipolar Transistor(IGBT) has been studied. we has analyzed with lifetimes excess minority carrier injected into N-dirft, base region of IGBT's BJT part and accumulated charge of on-state which affected swiching characteristic. In this paper, excess minority carrier and charge distribution in active base region is expressed analytically. This analysis proposed optical trade-off between lifetimes and accumulated charge for decreasing switching losses because charge result in switching loss when device was tuned off.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.557-560
• /
• 2003

Magnetorheological finishing(MRF) is a newly developed and recently commercialized for finishing optical components. The magnetorheological fluid consists of a water based suspension of carbonyl iron, nonmagnetic polishing abrasives, and small amounts of stabilizer. This magnetorheological fluid is pumped from conditioner on the rotating wheel and suctioned back to the conditioner, where it cooled to setpoint temperature and evaporative losses are replaced. This method could produce some problems in suction. So newly designed MRF tools is proposed in which MR fluid is not circulated and conditioned by the slurry. The new polishing mechanism is experimented. Measured surface roughness supports the validity of this mechanism.

• 대한전자공학회논문지
• /
• 제24권3호
• /
• pp.510-516
• /
• 1987

An analysis and numerical computations relating to the coupling of optical modes between two neighboring waveguides are discussed. The waveguides are fabricated with Lithium Niobate as guide 1 and Vanadium Oxide as guide 2. In a wave guide system that incorporates two lossless guides, a complete transfer of power from one guide to another can occur when the waveguides are (1) identical or (2) the modes in each guide have identical phase constants. Here we discuss the coupling effects when the guides are dissimilar with respect to both geometry and losses. In thers results, we show that power transfer can occur between the two guides, one lossy and the other lossless, provided the phase matched condition is satisfied. When properly coupled, the power attenuation varies according to the amount of coupling.

• 한국광학회지
• /
• 제13권6호
• /
• pp.473-478
• /
• 2002

원형으로 굽은 평판 광도파로를 직선 광도파로로 등각사상화 시켰다. 단조 증가하는 굴절률 분포를 갖는 바깥쪽 클래드영역의 누설모드를 표현하기 위해 진행파형 수정된 Airy함수가 처음으로 소개되었다. 모의 전산을 통해 유도된 방법에 의한 굽음손실 및 field해 분포를 계산하고, WKB에 의한 결과와 비교하였다. 모의 전산결과 기존의 WKB 방법에 비해 회기점에서 수렴하는 해를 구할 수 있었으며, 더 정확한 굽음 손실을 계산할 수 있었다.

• Macromolecular Research
• /
• 제12권5호
• /
• pp.437-442
• /
• 2004

We have fabricated a polymeric waveguide by using a hot embossing technique and have investigated its propagation loss. The replication of waveguide channels through the use of a hot embossing technique is of interest as a single-step process that could deliver surface roughnesses far smaller than the wavelength. We have evaluated experimentally that the sidewall roughness has a dominant effect on insertion losses of the multimode polymeric waveguide. The propagation loss of the waveguide decreased dramatically upon decreasing the sidewall roughness of the channel. We have confirmed that the preparation of waveguides having nanometer-scale sidewall roughness and 0.1 dB/cm propagation loss is possible when using the hot embossing technique.

• 한국광학회지
• /
• 제18권3호
• /
• pp.226-231
• /
• 2007

본 논문에서는 이중 금속선으로 이루어진 다양한 곡선형 도파로를 고려하고 이 구조들에서 전파하는 모드의 특성을 수치해석적으로 분석하였다. 이중 금속선들 간의 간격과 내부 유전체의 굴절률 변화에 따라 곡선형 도파로의 최적 반경과 최소손실의 경향을 조사하였으며, 그 결과 이중 금속선 구조가 단일 금속선 구조보다 전파특성이 좋은 최적 구조가 존재함을 확인하였다.

• KIEAE Journal
• /
• 제2권3호
• /
• pp.33-38
• /
• 2002

The intermediate range of temperatures($100{\sim}300^{\circ}C$) which can be achieved with CPCs(Compound Parabolic Concentrators) without tracking device provides both economic and thermal advantages for solar collector design. The present paper summarizes critical design considerations for CPC with cylindrical absorber and its optical performance using ray tracing program. Concentration ratios vary as acceptance half angle, ratio of reflector height to aperture width and ratio of reflector area to aperture area. This effects showed that the concentration ratio was increased as acceptance angle but optimum ratio of reflector height to aperture width existed at critical value. As a result of ray tracing, solar ray losses was maximized at acceptance half angle and this problem was solved by increasing absorber tube diameter. The concentrating flux distribution on the absorber surface was uniform but peak flux existed.