• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.3 s.180
• /
• pp.61-68
• /
• 2006

This paper is to investigate the influence of the endface quality on the loss characteristics of a plastic optical fiber(POF) connector and the stability of new designed sleeve for in-car network service. Using the parameters of the surface roughness and applied load, insertion loss of connector is measured. Endface condition for optimizing the connection is presented by the surface roughness satisfying loss criteria and the stress for minimizing the loss, $R_{rms}=8nm$ and 19 MPa, respectively. By vibration test and dynamic loss measurement, we show the stability of the new designed sleeve.

• Korean Journal of Optics and Photonics
• /
• v.6 no.4
• /
• pp.373-378
• /
• 1995

Bending losses of bent optical waveguides are calculated by virtue of the finite difference-beam p propagation method in the cylindrical coordinate system. In order to minimize the radiating losses of bent optical waveguides, we apply the trench structure to the bent waveguides and perform the a analysis to keep track of: 1) the influence of curvature radius on the bending loss without the trench, 2) the influence of curvature radius and refractive index difference on the bending loss with the trench, 3) the influence of the trench width on the bending loss.

• Journal of the Optical Society of Korea
• /
• v.9 no.1
• /
• pp.1-5
• /
• 2005

Using tightly focused femtosecond laser pulses, we produce an optical waveguide and optical devices in transparent materials. This technique has the potential to generate not only channel waveguides, but also three-dimensional optical devices. In this paper, an optical splitter and U-grooves, which are used for fiber alignment, are simultaneously fabricated in a fused silica glass using near-IR femtosecond laser pulses. The fiber aligned optical splitter has a low insertion loss, less than 4㏈, including an intrinsic splitting loss of 3㏈ and excess loss due to the passive alignment of a single-mode fiber. Finally, we demonstrate the utility of the femtosecond laser writing technique by fabricating gratings at the surface and inside the silica glass.

• Journal of the Optical Society of Korea
• /
• v.13 no.2
• /
• pp.256-260
• /
• 2009

The optical performance of the reflective polarizer was investigated over three kinds of direct-lit backlights and/or different configurations of the optical sheets. The optical gain factor achieved by using the reflective polarizer increased as the diffuse nature of the optical sheet was enhanced, because of the more efficient polarization conversion. In addition, the gain factor decreased substantially in flat-lamp backlights compared to tubular-lamp backlights, which was ascribed to the high loss factor during the polarization recycling process due to the complex structure and large area of flat lamps. All these results suggested that reducing the loss factor of the backlight is very important for efficient polarization conversion and thus high optical gain of the reflective polarizer.

• Transactions of Materials Processing
• /
• v.13 no.3
• /
• pp.211-215
• /
• 2004

Recently, one of remarkable tends in the development of optical communication industry is the miniaturization and integration of products. The alignment system of micro optical module is a key apparatus for the miniaturization of optical module and the development of optical communication parts with high functionality. In this research, we have developed a system capable of automatic alignment of a $30\mu\textrm{m}$-thick film filter and a lensed fiber in order to improve the speed and losses in the optical fiber-to-filter alignment of optical modules. Using the developed automatic alignment system and silicon optical bench, we have measured optical loss and characteristics of the assembled optical add/drop module before packaging $1{\times}1$ OADM optical module. Whole size of add/drop module was less than $5mm{\times}5mm{\times}1mm$. The measured maximum insertion loss was 0.294㏈ that is below 0.3㏈ which is a standard loss of optical module.

• Current Optics and Photonics
• /
• v.1 no.5
• /
• pp.468-473
• /
• 2017

We determined the feasibility of a fishing camera system using an optical fiber as the fishing line by testing a power-over-fiber (POF) module and multimode optical fiber. Operation of the remote camera module (RCM) without the battery was preferred because the removal of the charging or battery replacement section enabled a waterproof single-body type design. The average efficiency of the photovoltaic power converter (PPC) in the tested POF module was 32.6% at 820 nm, and thus, a high-power laser of at least 1.27 W was required for operating the developed RCM with an electrical dissipation of 413 mW. Because the optical fiber was wound on a fishing reel, composite loss composed of bending and tensile loss occurred. To mitigate the composite loss, we employed a simple holder that showed an improvement in the composite loss of 0.38 dB to 0.8 dB, which was considerably better than the losses without the holder.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.12
• /
• pp.1900-1905
• /
• 1990

In this study, the thermal neutron effects on optical fiber are examined theoretically. Also, the induced loss by thermal neutron irradiation in optical fibers is measured at the optical wavelengths of 0.85 and 1.3\ulcorner, respectively, and the results are analyzed. Thermal neutrons cause nuclear reaction with fiber compositions. So secondary ionizing radiations of high energy are generated. Color centers formed by these secondary ionizing rasiations increase transmission loss of optical fiber by absorbing propagating light in fiber core. As a result of experiment, owing to Ge, P, and B doping effects, the induced loss in multimode fibers has been 5 tmes larger than that in single mode fibers at 1.3 \ulcorner wavelengh. In case of multimode fibers, the loss at 0.8 \ulcorner wavelength region more suceptible for radiations has been twice higher than at 1.3\ulcorner.

• Journal of the Optical Society of Korea
• /
• v.13 no.3
• /
• pp.349-353
• /
• 2009

We propose a simple in-line variable optical attenuator (VOA) based on the bending effect of tapered single mode fibers. The influence of the taper structure and the reflective index of the external medium surrounding the taper region on the bending loss of the tapered fiber have been investigated experimentally. An attenuation range exceeding 35 dB and a very low excess loss of < 0.2 dB at 1550 nm were achieved. The measured polarization dependent loss of the present VOA at the attenuation level of 10 dB, 20 dB, and 30 dB were 0.1 dB, 0.2 dB, and 0.5 dB, respectively.

• Journal of information and communication convergence engineering
• /
• v.7 no.3
• /
• pp.377-382
• /
• 2009

In this paper, theoretical analysis for metropolitan optical networks is performed. First, analytical optical SNR is derived assuming each node consists of an EDFA, an optical filter, an optical switch, and a VOA, and then the relationship between OSNR and BER is studied. In a metropolitan optical network, an optical signal can be dropped to deliver data, and we also studied the effect of drop loss on system performance. When the drop loss is relatively small, the receiver structure of the node can be treated as a preamplifier receiver which is widely used in long-haul systems. In that case, ASE noise from EDFAs is the dominant noise source in the receiver. However, system performance is relatively insensitive to OSNR when the drop loss is significant because of the noise sources in the receiver (thermal and shot noise).

• ETRI Journal
• /
• v.27 no.4
• /
• pp.446-448
• /
• 2005

Using tightly focused femtosecond laser pulses, we produce an optical waveguide and devices in transparent materials. This technique has the potential to generate not only channel waveguides, but also three-dimensional optical devices. In this paper, an optical splitter and U-grooves, which are used for fiber alignment, are simultaneously fabricated in a fused silica glass using near-IR femtosecond laser pulses. The fiber- aligned optical splitter has a low insertion loss, less than 4 dB, including an intrinsic splitting loss of 3 dB and excess loss due to the passive alignment of a single-mode fiber. Finally, we present an output field pattern, demonstrating that the splitting ratio of the optical splitter becomes approximately 1:1.