• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.4
• /
• pp.506-516
• /
• 2007

In this paper, a study on low-velocity impact response of four different sandwich panels for the hybrid bodyshell and floor structure application of the Korean low floor bus vehicle was done. Square samples of 100mm sides were subjected low-velocity impact loading using an instrumented testing machine at six energy levels. Impact parameters like maximum force, time to maximum force, deflection at maximum force and absorbed energy were evaluated and compared for four different types of sandwich panels. The impact damage size and depth of the permanent indentation were measured by 3-Dimensional Scanner. Failure modes were studied by sectioning the specimens and observed under optical microscope. The impact test results show that sandwich panel with composite laminate facesheet could not observe damage mode of a permanent visible indentation after impact and has a good impact damage resistance in comparison with sandwich panel with metal aluminum facesheet.

• Journal of Sensor Science and Technology
• /
• v.5 no.6
• /
• pp.15-24
• /
• 1996

In this study, as a part of the basic study for the application of optical fiber sensors to smart composite structures, the integrity of optical fiber sensors embedded within the composite structures was examined and then the laser signal transmitted through optical fiber sensors during the deformation of host structures was investigated. Firstly, it was found that bending test could be substituted for tensile test by comparing cumulative failure distribution based on weakest link theory and introducing the correction factor. Weibull parameters were obtained through the experiments and the correction factor was found to be applied to cumulative failure distribution derived from bending test. The integrity of embedded optical fiber sensors due to the thermal effect was evaluated by the comparison of the mean tensile strengths of cured and uncured optical fibers. Secondly, relationships between stress-strain curve obtained in tensile test of composite laminate and the intensity of laser signal transmitted through embedded optical fibers were examined and the possibility of the effective damage detection using optical fiber sensors was studied.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.10
• /
• pp.1551-1558
• /
• 2001

Recently, a number of underground pipelines have been drastically increased. The integrity of these buried pipelines, especially gas transmitting pipelines, is of importance due to an explosive characteristic of natural gas. The third party damage is known as one of the most critical factor which causes fatal accidents. For this reason, a number of systems detecting third party damage are under development. The major concern in the development of third party damage detection system is to transmit vibration signals out of accelerometer to signal conditioner and data acquisition system without any interference caused by noise. The objective of this paper is to develope a fiber optic accelerometer applicable to third party damage detection system. A fiber optic accelerometer was developed by use of combining principles of one degree of freedom vibration model and an extrinsic Fabry-Perot interferometer. The developed fiber optic accelerometer was designed to perform with a sensitivity of 0.06mVg, a frequency range of less than 6kHz and an amplitude range of -200g to 200g. The developed, accelerometer was compared with a piezoelectric accelerometer and calibrated. In order to verify the developed accelerometer, the field experiment was performed. From the field experiment, vibration signals and the location of impact were successfully detected. The developed accelerometer is expected to be used for the third party damage detection system which requires long distance transmission of signals.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.290.1-290.1
• /
• 2016

Grapehen, a single atomic layer of graphite, has been in the spotlight and researched in vaious fields, because its fine mechanical, electrical properties, flexibility and transparence. Synthesis methods for large-area graphene such as chemical vaper deposition (CVD) and mechanical, chemical exfoliation have been reported. In particular, chemical exfoliation method receive attention due to low cost process. Chemical exfoliation method require reduction of graphene oxide in the process of exfoliation such as chemical reduction by strong reductant, thermal reduction on high temperature, and optical reduction via ultraviolet light exposure. Among these reduction methods, optical reduction is free from damage by strong reductant and high temperature. However, optical reduction is economically infeasible because the high cost of short-wavelength ultraviolet light sorce. In this paper, we make graphene-oxide and lanthanoid ion mixture aqueous solution which has highly optical absorbency in selective wevelength region. Sequentially, we synthesize reduced graphene oxide (RGO) using the solution and visible laser beam. Concretely, graphene oxide is made by modified hummer's method and mix with 1 ml each ultraviolet ray absorbent Gd3+ ion, Green laser absorbent Tb3+ ion, Red laser absorbent Eu3+ ion. After that, we revivify graphene oxide by laser exposure of 300 ~ 800 nm layser 1mW/cm2 +. We demonstrate reproducibility and repeatability of RGO through FT-IR, UV-VIS, Low temperature PL, SEM, XPS and electrical measurement.

• Journal of the Optical Society of Korea
• /
• v.17 no.1
• /
• pp.103-108
• /
• 2013

The operation of a Doppler wind LIDAR in a mobile environment is very sensitive to shocks and vibrations, which can cause critical failures such as misalignment of the optical path and damage to optical components. To be able to stabilize the LIDAR and to perform wind field measurements in motion, a shock absorption and vibration isolation system was designed and implemented. The performance of the vehicle-mounted Doppler wind LIDAR was tested in motion, first in a circular test route with a diameter of about 30 m and later in regular expressway traffic. The vibration isolation efficiency of the system was found to be higher than 82% in the main vibration area and shock dynamic deflection was smaller than maximal deflection of the isolator. The stability of the laser locking frequency in the same mobile environment before and after the vibration isolation system installation was also found to be greatly improved. The reliability of the vibration isolation system was confirmed by good results of the analysis of the LIDAR data, in particular the plane position indicator of the line of sight velocity and the wind profile.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.1
• /
• pp.25-29
• /
• 2014

In this study, an optical PCB was proposed which can overcome the limitations of the conventional PCB, and a new structure with pluggable lens was considered for a high-efficient passive alignment. The structure was a lens-added optical waveguide for the improvement of misalignment between the lens and the waveguide in the alignment. Also, as it had a barrier-type structure to prevent the surface damage of the lens by desorption, the high-efficient passive alignment can be realized. The structure was designed by optimizing the simulation and the fabrication process of the pluggable lens structure was conducted using the repetitive photolithography and the thermal reflow. The optical waveguide with the lens-integrated pluggable interconnection was fabricated by the imprint process using the polydimethylsiloxane(PDMS) replica mold. Therefore, we confirmed the possibility of pluggable lens-added optical waveguide structure fabrication for high-efficient passive alignment.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.2
• /
• pp.47-53
• /
• 2012

Recently, by the increasing of data transmission rates, PCB is required high-speed data transmission rates and thin packaging. So optical PCB which is the combination of electrical layer and optical layer can be one of the solution to overcome the limitations of conventional electrical PCB. The most important factor in the implementation of optical PCB is optical interconnection. So the research on high-efficiency and passive alignment has been active. In this paper, we suggest built-in lens pluggable waveguide and we simulate its coupling efficiency and structural stability. Optical simulation results show that the proposed structure has higher efficiency than no lens structure about 1.86 times in transmitter and about 1.42 times in receiver. In structure simulation, inner lens has no damage in desorption process. Therefore, we shown that the proposed structure has a high coupling efficiency and structural stability.

• Composites Research
• /
• v.16 no.4
• /
• pp.44-50
• /
• 2003

The damage zone around a crack tip occurring before the fracture is a significant domain. which affects the toughening mechanism of materials. In this study. the growth process of damage zone in the vicinity of crack tip for rubber-modified epoxy resin is investigated using an acoustic emission(AE) analysis. The weight fractions of rubber(CTBN 1300$\times$B) in rubber-modified epoxy resin are 5 wt% and 15 wt%. The fracture toughness($K_{IC}$) and the fracture energy($G_{IC}$) were measured using 3 point bending single-edge notched specimens. The damage zone and rubber particles distributed around the crack tip were observed by a polarized optical microscope and an atomic force microscope(AFM). The damage zone around crack tip of rubber-modified epoxy resin was formed at 13 % loading and developed until 57 % loading of the fracture load. The crack initiated at 57 % loading grew repeatedly in the stick-slip propagation behavior. Based on time-frequency analysis, it was confirmed that AE signals with frequency bands of 0.15~0.20 MHz and 0.20~0.30 MHz were generated from cavitation and stable/unstable cracking inside the damage zone.

• Journal of Korean Medicine for Obesity Research
• /
• v.17 no.2
• /
• pp.77-86
• /
• 2017

Objectives: This study examined the effects of salvianolic acid B (SAB) on exhaustive exercise-induced cardiac muscle damage to rats. Methods: The study was carried out with 12-week-old young adult male Sprague-Dawley rats. Thirty-six rats were divided into 3 groups; normal (n=12), exhaustive exercise group (ExS, n=12) and exhaustive exercise with SAB (ExS+SAB, n=12). Five days before exhaustive exercise, SAB were medicated for 5 days in ExS+SAB group. Rats in ExS and ExS+SAB group were forced to swim for 150 minutes and then they were sacrificed, while rats in normal group were sacrificed at rest. After that, blood was collected and cardiac muscle tissue damage indices were analyzed. Results: Serum aspartate transaminase activity and lactate dehydrogenase activity were significantly lower in ExS+SAB group than in ExS group. Serum creatine phosphokinase activity of ExS+SAB was significantly lower than ExS group. However, the content of serum creatinine had no difference between ExS and ExS+SAB group. In the H&E stained left ventricle myocardium, ExS group showed signs of myocardial damage such as sporadic fragmentation of myocardial fibers, interstitial edema, cytoplasmic eosinophilia and neutrophils infiltration. However, ExS+SAB group alleviated the severity of the signs of myocardial damage. In the myocardial dihydroethidium staining, optical density was remarkably decreased in ExS+SAB group compared to ExS group. Furthermore, the up-regulation of Bax/Bcl-2 ratio was observed in ExS+SAB group compared with ExS group. Conclusions: The above results suggest that SAB may protect cardiac muscle damage via antioxidant activity and prevention of apoptosis.

• Journal of Power System Engineering
• /
• v.21 no.3
• /
• pp.102-107
• /
• 2017

A tungsten inert gas (TIG) welding method was used for the bonding of stainless steel. TIG welding using inert gas (He or Ar gas) is a method to prevent oxidation and nitriding of materials and to combine non-ferrous metals. This method has the advantage of obtaining a smooth weld surface. In this study, the welding characteristics of 304 stainless steel welded by TIG welding method were analyzed by using nondestructive technique. Ultrasonic and Acoustic Emission (AE) was applied to evaluate the micro-damage of TIG welded 304 stainless steel. The velocity and damping coefficient of ultrasonic wave showed a slight difference in HAZ, which is the welding part of stainless steel. The AE parameters of average frequency, rise time and event were analyzed for the dynamic behavior of stainless steel during loading. Optimal AE parameters for evaluating the degree of damage to the specimen have been derived. Fractograph and metal structures of 304 stainless steel using SEM and optical microscope were discussed.