• 비파괴검사학회지
• /
• 제34권2호
• /
• pp.165-170
• /
• 2014

수평횡파(SH-wave)는 배관과 같은 박판 구조물에서 판파 모드로 전파하고 분산성이 단순하여 구조물의 건전성 평가에 유용하다. 전자기초음파탐촉자(EMAT)는 비접촉식으로 자석과 코일 배열을 조절하여 수평횡파를 발생하기 용이하다. 따라서 수평횡파 전자기초음파탐촉자(SH-EMAT)를 이용한 자동화 검사 시스템은 박판 구조물 건전성 감시에 매우 유용하다. 하지만 발전설비 또는 자동화 장비 등에서는 전자기노이즈가 상당히 많이 발생하고 EMAT 수신 센서는 전자기노이즈에 취약한 면이 있다. 광섬유 센서는 빛을 이용하여 전자기노이즈 환경에서 매우 유용하게 활용될 수 있다. 본 연구에서는 이러한 환경적 제약을 고려하여 광섬유 패브리-페롯 간섭계(FFPI)를 SH-EMAT으로 발생되는 초음파의 수신용 센서로 제안하였다. 평판시험편에서 SH-EMAT의 신호를 FFPI 센서를 이용하여 수신하고 이 신호에 대한 분석을 하였다. 제안된 FFPI 센서가 EMAT으로 가진된 SH wave의 신호를 명료하게 수신할 수 있음을 확인하였다.

• 한국광학회지
• /
• 제29권6호
• /
• pp.241-246
• /
• 2018

본 논문에서는 광섬유 브래그 격자(FBG)를 이용한 광온도센서를 제작하였으며 광원은 출력 파장의 온도 의존성을 가지는 저가형 VCSEL이 사용되며 FBG에서 반사되는 빛의 파장을 분석하는 interrogator는 VCSEL에서 변화되는 출력 파장을 VCSEL의 내부 온도로 확인하는 방법을 적용하여 저가격의 광온도센서를 구현하였다. VCSEL의 내부온도를 $52.2^{\circ}C$에서 $14^{\circ}C$까지 조절하면서 출력 파장을 1519.90 nm에서 1524.25 nm까지 총 4.35 nm 파장을 변화시켰으며 온도 조절에 따른 파장 변화 반복도 오차는 ${\pm}0.003nm$이며 온도 측정 오차는 ${\pm}0.18^{\circ}C$로 측정되었다. 광온도센서를 사용하여 $22.3{\sim}194.2^{\circ}C$의 온도를 측정한 결과 인가한 온도 ${\Delta}T$에 따른 광원 내부 온도 변화 값은 $0.146^{\circ}C/{\Delta}T$이고 인가한 온도 ${\Delta}T$에 따른 온도 프로브 반사 파장 변화 값(${\Delta}{\lambda}_{\beta}T/{\Delta}T$)은 $16.64pm/^{\circ}C$로 측정되었으며 센서의 측정 오차는 ${\pm}1^{\circ}C$로 나타났다. VCSEL의 출력 파장은 온도에 의존성을 가지고 있어 좁은 범위의 출력 파장을 변화시키기 위한 광원으로 사용하기에 매우 적합하다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1748-1750
• /
• 2004

This paper deals with the detection method of the Quench phenomenon for superconducting magnet using the Acoustic Emission (AE) sensor. AE sensor is the elements, which is used to change the Acoustic signal to the voltage value. This signal may be used to detect whether the superconducting magnet has been at the Quench state or not. Recently, the development of the Quench detection technique, which is the using voltage and current signals, fiber-optic sensor, and so on, for the superconducting applications is widely studying. This method for the Quench detection of the superconducting magnet is also studying at some kinds of institute in Japan and the united state. Because of the large-scale superconducting magnet like International Thermonuclear Experimental Reactor(ITER) is charged a lot of energy, when the Quench phenomenon is being at the superconducting magnet it is happen to the problem of the protection for the applications. In this paper, we concluded that the Quench detection was possible when the mechanical stress by means of the local heat is generated at the part of inside superconducting magnets.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1391-1393
• /
• 1995

An electron gun system for the Pohang Light Source has been installed and operated successfully. The basic design parameters are acceleration voltage of 80 kV, maximum peak emission current of 5 A, minimum pulse width of 1 ns, and maximum repetition rate of 100 Hz. The gun has a triode structure and is composed of a cathode, a focusing electrode(Wehnelt), and an anode. To sustain a $5{\times}10^{-9}$Torr vacuum, a $230{\ell}/s$ Ion pump has been adopted. We adopted a control and monitoring system based on the fiber-optic technology. In this article, we present the structure and operation principle of the system with special interest on the nanosecond pulser, remote control and monitoring system.

• 대한전자공학회논문지SD
• /
• 제44권11호
• /
• pp.36-42
• /
• 2007

레이저 다이오드를 사용하여 전기신호를 광신호로 변환해 주는 버스트 모드 광송신기용 온도보상 방식에 대하여 연구하였다. 기존 실시간 아날로그 방식의 온도보상 방법에 비해, 본 연구에서는 마이크로프로세서를 사용하여 디지털 방식으로 신호를 샘플링 처리함으로써 고속 버스트 모드 광신호를 효과적으로 처리할 수 있도록 하였다. 온도보상을 위한 디지털 자동전력조절방식은 아날로그 방식에 비해 보다 정확하고 효율적이다. 따라서 이 방식은 앞으로 개발된 Gb/s 이상의 고속 버스트 광신호처리에 유용하게 사용될 수 있을 것으로 본다.

• Smart Structures and Systems
• /
• 제18권6호
• /
• pp.1203-1215
• /
• 2016

When strain sensing cables are under long-term stress and cyclic loading, creep may occur in the jacket material and each layer of the cable structure may slide relative to other layers, causing fatigue in the cables. This study proposes a device for testing the fatigue characteristics of three types of cables operating under different conditions to establish a decay model for observing the patterns of strain decay. The fatigue characteristics of cables encased in polyurethane (PU), GFRP-reinforced, and wire rope-reinforced jackets were compared. The findings are outlined as follows. The cable strain decayed exponentially, and the decay process involved quick decay, slow decay, and stabilization stages. Moreover, the strain decay increased with the initial strain and tensile frequency. The shorter the unstrained period was, the more similar the initial strain levels of the strain decay curves were to the stabilized strain levels of the first cyclic elongation. As the unstrained period increased, the initial strain levels of the strain decay curves approached those of the first cyclic elongation. The tested sensing cables differed in the amount and rate of strain decay. The wire rope-reinforced cable exhibited the smallest amount and rate of decay, whereas the GFRP-reinforced cable demonstrated the largest.

• 대한기계학회논문집B
• /
• 제20권8호
• /
• pp.2601-2610
• /
• 1996

Surface protrusions have been attached on a cylinder surface to reduce the flow-induced structural vibration by controlling the wake flow. Wind tunnel tests on the near wake of a circular cylinder with surface protrusions were carried out to investigate the flow characteristics of the controlled wake. Three experimental models were used in this experiment; one plain cylinder of diameter D and two cylinders wrapped helically by three small wires of diameter d=0.075D with pitches of 5D and 10D, respectively. Free stream velocity was ranged to have Reynolds number from 5000 to 50,000. Streamwise and vertical velocity components of the wake were measured by a hot-wire anemometry. The spanwise velocity component measured by a one-component fiber optic LDV revealed that time-averaged wake field has a nearly two-dimensional structure. It was found that the surface protrusions elongate the vortex formation region, which decrease the vortex shedding frequency. The suppression of vortices caused by the surface protrusions increases the velocity deficit in the center of wake region.

• 전기학회논문지
• /
• 제57권3호
• /
• pp.403-408
• /
• 2008

The gyroscope is the sensor for detecting the rotation in inertial reference frame and constitute the navigation system together an accelerometer. As the inertial reference equipment for attitude determination and control in the satellite, the mechanical gyroscope has been used but it bring the disturbance for mass unbalance so the disturbance give a bad influence to the observation satellite mission because the mechanical gyroscope has the rotation parts. During the launch. The mechanical gyroscope is weak in vibration, shock and has the defect of narrow operating temperature range so it need the special design in integration. Recently the low orbit observation satellite for seeking the high pointing accuracy of image camera payload accept the FOG(Fiber Optic Gyro) or RLG(Ring Laser Gyro) for the attitude determination and control. The Ring Laser Gyro makes use of the Sanac effect within a resonant ring cavity of a He-Ne laser and has more accuracy than the other gyros. It need the 1000V DC to create the He-Ne plasma in discharge tube. In this paper, the design process of the High Voltage Power Supply for RLG(Ring Laser Gyroscope) is described. The specification for High Voltage Power Supply (HVPS) is proposed. Also, The analysis of flyback converter topology is explained. The Design for the HVPS is composed of the inverter circuit, feedback control circuit, high frequency switching transformer design and voltage doubler circuit.

• 대한치과보철학회지
• /
• 제29권3호
• /
• pp.171-179
• /
• 1991

The purpose of this study was to investigate the color stability of 3 porcelain repair composite resins Twenty specimens of each composite resin were made and ten specimens were polished at 10 minutes after polymerization, and the others were polished at 48 hours after polymerization. For 60 days, the color characteristics were measured by fiber-optic colorimeter (Model Tc-6FX, Tokyo Denshoku Co.). The obtained results were as follows: 1. The changes of $a^*$ value and $b^*$ value in composite resin polished at 10min. after polymerization were greater than those of composite resins polished at 48 hrs. after polymerization. 2. The $a^*$ values of all composite resins were increased and the $b^*$ values were decreased. 3. The $L^*$ values were decreased in composite resin manufactured by K & B Co., which were polished at 10min. after polymerization, but increased in composite resin manufactured by K & M Co., polished at 48 hrs. after polymerization.

• 대한치과보철학회지
• /
• 제29권3호
• /
• pp.111-119
• /
• 1991

This study was performed to investigate the effect of gold electrodepositoin on porcelain color of palladium-silver alloy. The specimens were made by firing porcelain on the metal plates cast respectively in Au-Pt alloy, and Pd-Ag alloy. In the case of Pd-Ag alloy specimens, porcelain were fired under three different conditions of the metal plate: 1) without gold coating, 2) firing opaque beforehand on one side, gold coating on the other side, 3) gold coating on both sides of the metal plate. Color change was measured with fiber-optic colorimeter(Model TC-6FX, Tokyo Denshoku Co., Japan). The obtained results were as follows: 1. In the group of firing opaque beforehand on one side and gold coating on the other side, there was no significant differences in their color in comparison to the color of the control group of the Au-Pt alloys. 2. In the group of gold coating on both sides on metal plate, there were no significant differences except their value to the group of firing poaque beforehand on one side and gold coating on the other side.